iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 61803:1999

(Main)

Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters

Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters

Applies to all line-commutated high-voltage direct current (HVDC) converter stations used for power exchange in utility systems. Presumes the use of 12-pulse thyristor converters but can also be used for 6-pulse thyristor converters. Presents procedures for determining the total losses of an HVDC converter station. Cover all parts, except synchronous compensators or static var compensators and address no-load operation and operating losses together with their methods of calculation which use, wherever possible, measured parameters.

Bestimmung der Leistungsverluste in Hochspannungsgleichstrom- (HGÜ-)Stromrichterstationen mit netzgeführten Stromrichtern

Détermination des pertes en puissance dans les postes de conversion en courant continu à haute tension (CCHT) munis de convertisseurs commutés par le réseau

S'applique à tous les postes de conversion en courant continu à haute tnesion (CCHT), commutés par le réseau, et utilisés pour l'échange de puissance dans des systèmes de distribution d'énergie. Présuppose l'utilisation de convertisseurs à thyristors à 12 impulsions mais peut également s'appliquer à des convertisseurs à thyristors à 6 impulsions. Décrit un ensemble de procédures types permettant de déterminer l'ensemble des pertes d'un poste de conversion à CCHT. Les procédures recouvrent toutes les pièces, à l'exception des compensateurs synchrones ou des compensateurs var statiques et considèrent les pertes en fonctionnement à vide et les pertes en fonctionnement ainsi que leurs méthodes de calcul utilisant, dans la mesure du possible, des paramètres mesurés.

Determination of power losses in high-voltage direct current (HVDC) converter stations (IEC 61803:1999)

Velja za vse vodovno komutirane visokonapetostne enosmerne (HVDC) pretvornike, ki se uporabljajo za izmenjavo električne energije v javnih sistemih. Ta standard predvideva uporabo 12-pulznih tiristorksih pretvornikov, vendar se lahko uporablja tudi za 6-pulzne tiristorske pretvornike ob ustrezni previdnosti.

General Information

Status
Withdrawn
Publication Date
31-Mar-1999
Withdrawal Date
31-Mar-2002
ICS
29.200 - Rectifiers. Convertors. Stabilized power supply
Technical Committee
CLC/TC 22X - Power electronics
Drafting Committee
IEC/SC 22F - IEC_SC_22F
Parallel Committee
IEC/SC 22F - IEC_SC_22F
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
23-Nov-2023
Completion Date
23-Nov-2023
Ref Project
SIST EN 61803:2001 - Determination of power losses in high-voltage direct current (HVDC) converter stations

Relations

Replaced By
EN IEC 61803:2020 - Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters
Effective Date
20-Nov-2018
Amended By
EN 61803:1999/A1:2010 - Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters
Effective Date
29-Jan-2023
Amended By
EN 61803:1999/A2:2016 - Determination of power losses in high-voltage direct current (HVDC) converter stations with line commutated converters
Effective Date
07-Jun-2022

Buy Standard

EN 61803:2001EN 61803:2001
PreviousNext
Standard
EN 61803:2001
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61803:2001
01-junij-2001
Determination of power losses in high-voltage direct current (HVDC) converter
stations (IEC 61803:1999)
Determination of power losses in high-voltage direct current (HVDC) converter stations
Bestimmung der Leistungsverluste in Hochspannungsgleichstrom- (HGÜ-)
Stromrichterstationen
Détermination des pertes en puissance dans les postes de conversion en courant
continu à haute tension (CCHT)
Ta slovenski standard je istoveten z: EN 61803:1999
ICS:
29.200 8VPHUQLNL3UHWYRUQLNL Rectifiers. Convertors.
6WDELOL]LUDQRHOHNWULþQR Stabilized power supply
QDSDMDQMH
SIST EN 61803:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61803:2001

---------------------- Page: 2 ----------------------

SIST EN 61803:2001

---------------------- Page: 3 ----------------------

SIST EN 61803:2001

---------------------- Page: 4 ----------------------

SIST EN 61803:2001

---------------------- Page: 5 ----------------------

SIST EN 61803:2001

---------------------- Page: 6 ----------------------

SIST EN 61803:2001

---------------------- Page: 7 ----------------------

SIST EN 61803:2001

---------------------- Page: 8 ----------------------

SIST EN 61803:2001

---------------------- Page: 9 ----------------------

SIST EN 61803:2001

---------------------- Page: 10 ----------------------

SIST EN 61803:2001

---------------------- Page: 11 ----------------------

SIST EN 61803:2001

---------------------- Page: 12 ----------------------

SIST EN 61803:2001

---------------------- Page: 13 ----------------------

SIST EN 61803:2001

---------------------- Page: 14 ----------------------

SIST EN 61803:2001

---------------------- Page: 15 ----------------------

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 61800-5-3:2023(Main)
Adjustable speed electrical power drive systems - Part 5-3: Safety requirements - Functional, electrical and environmental requirements for encoders
SIST EN IEC 61800-5-3:2024

IEC 61800-5-3:2021, which is a product standard, specifies requirements and makes recommendations for the design and development, integration and validation of safety-related encoder (Encoder(SR)) in terms of their functional safety considerations, electrical safety and environmental conditions. It applies to Encoder(SR), being sensors as part of a PDS(SR). This document can also be referred to and used for Encoder(SR) in any other safety-related application, for example safety-related position monitoring. This document is applicable where functional safety of an encoder is claimed and the Encoder(SR) is operating mainly in the high demand or continuous mode. The requirements of IEC 61800-5-2:2016 for PDS(SR) apply to Encoder(SR) as applicable. This document includes additional or different requirements for Encoder(SR). It sets out safety-related considerations of Encoder(SR) in terms of the framework of IEC 61508 (all parts), and introduces requirements for Encoder(SR) as subsystems of a safety-related system. It is intended to facilitate the realisation of the electrical/electronic/programmable electronic (E/E/PE) and mechanical parts of an Encoder(SR) in relation to the safety performance of safety sub-function(s) of an Encoder(SR).

  • Standard
    108 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62477-1:2023(Main)
Safety requirements for power electronic converter systems and equipment - Part 1: General
SIST EN IEC 62477-1:2024

IEC 62477-1:2022 applies to power electronic converter systems (PECS), any specified accessories, and their components for electronic power conversion and electronic power switching, including the means for their control, protection, monitoring and measurement, such as with the main purpose of converting electric power, with rated system voltages not exceeding 1 000 V AC or 1 500 V DC. This document also applies to PECS which intentionally emit or receive radio waves for the purpose of radio communication. This document can also be used as a reference standard for product committees producing product standards for:  
adjustable speed electric power drive systems (PDS);
standalone uninterruptible power systems (UPS);
low voltage stabilized DC power supplies;
bidirectional power converters.  For PECS and their specified accessories for which no product standard exists, this document provides minimum requirements for safety aspects. This document has the status of a group safety publication in accordance with IEC Guide 104 for power electronic converter systems for solar, wind, tidal, wave, fuel cell or similar energy sources. According to IEC Guide 104, one of the responsibilities of technical committees is, wherever applicable, to make use of basic safety publications and/or group safety publications in the preparation of their product standards. Guidance for use of this group safety publication for product committees is given in Annex S. This document  
establishes a common terminology for safety aspects relating to PECS,
establishes minimum requirements for the coordination of safety aspects of interrelated parts within a PECS,
establishes a common basis for minimum safety requirements for the PECS portion of products that contain PECS,
specifies requirements to reduce risks of fire, electric shock, thermal, energy and mechanical hazards, during use and operation and, where specifically stated, during service and maintenance, and
specifies minimum requirements to reduce risks with respect to PECS designed as pluggable and permanently connected equipment, whether it consists of a system of interconnected units or independent units, subject to installing, operating and maintaining the PECS in the manner prescribed by the manufacturer.  This document does not cover  
telecommunications apparatus other than power supplies to such apparatus,
functional safety aspects as covered by, for example, IEC 61508 (all parts), and
electrical equipment and systems for railways applications and electr

  • Standard
    257 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 62040-1:2019/A1:2023(Amendment)
Uninterruptible power systems (UPS) - Part 1: Safety requirements
SIST EN IEC 62040-1:2019/A1:2024

No scope available

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61800-3:2023(Main)
Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods for PDS and machine tools
SIST EN IEC 61800-3:2024

IEC 61800-3:2022 specifies electromagnetic compatibility (EMC) requirements for adjustable speed power drive systems (PDSs) and machine tools (MTs). A PDS is an AC or DC motor drive including an electronic converter. Requirements are stated for AC and DC PDSs and MTs with input and/or output voltages (line-to-line voltage), up to 35 kV AC RMS. This document applies to equipment of all power ratings. As a product EMC standard, this document can be used for the assessment of PDS and MT. It can also be used for the assessment of complete drive modules (CDM) or basic drive modules (BDM). Traction applications and electric vehicles are excluded. Equipment which is defined as group 2 in CISPR 11:2015 is excluded. This document does not give requirements for the electrical machine which converts power between the electrical and mechanical forms within the PDS. Requirements for rotating electrical machines are covered by the IEC 60034 series. In this document, the term "motor" is used to describe the electrical machine, whether rotary or linear, and regardless of the direction of power flow. This document is applicable to BDMs, CDMs, PDSs and MTs with or without radio function. However, this document does not specify any radio transmission and reception requirements. This document defines the minimum requirements for emission and immunity in the frequency range from 0 Hz to 400 GHz. Tests are not required in frequency ranges where no requirements are specified. This fourth edition cancels and replaces the third edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
extension of the scope to machine tools with one or more embedded PDS;
extension of the frequency range for radiated immunity tests to 6 GHz;
general updates in the normative part and the informative annexes.

  • Standard
    133 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61800-5-1:2023(Main)
Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal and energy
SIST EN IEC 61800-5-1:2024

IEC 61800-5-1:2022 specifies requirements for adjustable speed electrical power drive systems (PDS) or their elements, with respect to electrical, thermal, fire, mechanical, energy and other relevant hazards. It does not cover the driven equipment except for interface requirements. It applies to adjustable speed electrical PDS which include the power conversion, basic drive module (BDM)/complete drive module (CDM) control, and a motor or motors. Excluded are traction and electric vehicle BDM/CDM. It applies to low-voltage adjustable speed electrical PDS intended to feed a motor or motors from a BDM/CDM connected to phase-to-phase voltages of up to and including 1,0 kV AC (50 Hz or 60 Hz) and up to and including 1,5 kV DC. It also applies to high-voltage adjustable speed electrical PDS intended to feed a motor or motors from a BDM/CDM connected to phase-to-phase voltages of up to and including 35 kV AC (50 Hz or 60 Hz) and up to and including 52 kV DC. This document also applies to PDS which intentionally emits or receives radio waves for the purpose of radio communication. This edition includes the following significant technical changes with respect to the previous edition: a) harmonization with IEC 62477-1:2022; b) harmonization with UL 61800-5-1 and CSA C22.2 No. 274, including an annex with a list of national deviation which was considered not possible to harmonize within a reasonable timeframe; c) more detailed information about the evaluation of components according to this document and relevant safety component standards; d) updated requirement for mechanical hazards including multiple IP ratings.

  • Standard
    446 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62751-2:2014/A2:2023(Amendment)
Power losses in voltage sourced converter (VSC) valves for high-voltage direct current (HVDC) systems - Part 2: Modular multilevel converters
SIST EN 62751-2:2014/A2:2024
  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62927:2017/A1:2023(Amendment)
Voltage sourced converter (VSC) valves for static synchronous compensator (STATCOM) - Electrical testing
SIST EN 62927:2018/A1:2023
  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60700-3:2023(Main)
Thyristor valves for high voltage direct current (HVDC) power transmission - Part 3: Essential ratings (limiting values) and characteristics
SIST EN IEC 60700-3:2023

This part of IEC 60700 specifies the service conditions, the definitions of essential ratings and characteristics of thyristor valves utilized in line commutated converters with three-phase bridge connections to realize the conversion from AC to DC and vice versa for high voltage direct current (HVDC) power transmission applications. It is applicable for air insulated, liquid cooled and indoor thyristor valves.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 62751-1:2014/A2:2022(Amendment)
Power losses in voltage sourced converter (VSC) valves for high-voltage direct current (HVDC) systems - Part 1: General requirements
SIST EN 62751-1:2014/A2:2022
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 60700-1:2015/A1:2021(Amendment)
Thyristor valves for high voltage direct current (HVDC) power transmission - Part 1: Electrical testing
SIST EN 60700-1:2015/A1:2022

No scope available

  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day