Integrated circuits - EMC evaluation of transceivers - Part 3: CAN transceivers

This part of IEC 62228 specifies test and measurement methods for EMC evaluation of CAN transceiver ICs under network condition. It defines test configurations, test conditions, test signals, failure criteria, test procedures, test setups and test boards. It is applicable for CAN standard transceivers, CAN transceivers with partial networking functionality and CAN transceivers with flexible data rate capability and covers - the emission of RF disturbances, - the immunity against RF disturbances, - the immunity against impulses, and - the immunity against electrostatic discharges (ESD).

Integrierte Schaltungen - Bewertung der elektromagnetischen Verträglichkeit von Sende-Empfangsgeräten - Teil 3: CAN-Sende-Empfangsgeräte

Circuits intégrés - Évaluation de la CEM des émetteurs-récepteurs - Partie 3: Émetteurs-récepteurs CAN

La présente partie de l'IEC 62228 spécifie les méthodes d'essai et de mesure pour l'évaluation de la compatibilité électromagnétique (CEM) des circuits intégrés émetteursrécepteurs CAN placés en réseau. Elle définit les configurations d'essai, les conditions d'essai, les signaux d'essai, les critères de défaillance, les modes opératoires d'essai, les dispositions d'essai et les cartes d'essai. Elle est applicable aux émetteurs-récepteurs CAN standard, aux émetteurs-récepteurs CAN avec une fonctionnalité de mise en réseau partielle et aux émetteurs-récepteurs CAN avec une capacité de taux de transfert flexible et couvre - l'émission de perturbations radioélectriques, - l'immunité aux perturbations radioélectriques, - l'immunité aux transitoires électriques, et - l'immunité aux décharges électrostatiques (DES).

Integrirana vezja - Vrednotenje elektromagnetne združljivosti (EMC) oddajnikov-sprejemnikov - 3. del: Oddajniki-sprejemniki CAN (IEC 62228-3:2019)

Ta del standarda IEC 62228 določa preskusne in merilne metode za vrednotenje elektromagnetne združljivosti integriranih vezij oddajnikov-sprejemnikov CAN pri omrežnih pogojih. Opredeljuje konfiguracije preskusov, preskusne pogoje, preskusne signale, merila za neuspešno opravljen preskus, preskusne postopke, nastavitve preskusa in preskusne plošče. Uporablja se za standardne oddajnike-sprejemnike CAN, oddajnike-sprejemnike CAN z delno omrežno funkcijo in oddajnike-sprejemnike CAN s prilagodljivo hitrostjo podatkov ter zajema
• oddajanje radiofrekvenčnih motenj,
• odpornost na radiofrekvenčne motnje,
• odpornost na impulze in
• odpornost na elektrostatične razelektritve (ESD).

General Information

Status
Published
Publication Date
02-May-2019
Withdrawal Date
14-Apr-2022
Current Stage
6060 - Document made available - Publishing
Start Date
03-May-2019
Completion Date
03-May-2019

Relations

Buy Standard

Standard
EN IEC 62228-3:2019
English language
77 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2019
Integrirana vezja - Vrednotenje elektromagnetne združljivosti (EMC) oddajnikov-
sprejemnikov - 3. del: Oddajniki-sprejemniki CAN (IEC 62228-3:2019)
Integrated circuits - EMC evaluation of transceivers - Part 3: CAN transceivers (IEC
62228-3:2019)
Integrierte Schaltungen - Bewertung der elektromagnetischen Verträglichkeit von Sende-
Empfangsgeräten - Teil 3: CAN-Sende-Empfangsgeräte (IEC 62228-3:2019)
Circuits intégrés - Évaluation de la CEM des émetteurs-récepteurs - Partie 3: Émetteurs-
récepteurs CAN (IEC 62228-3:2019)
Ta slovenski standard je istoveten z: EN IEC 62228-3:2019
ICS:
31.200 Integrirana vezja, Integrated circuits.
mikroelektronika Microelectronics
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 62228-3

NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2019
ICS 31.200
English Version
Integrated circuits - EMC evaluation of transceivers - Part 3:
CAN transceivers
(IEC 62228-3:2019)
Circuits intégrés - Évaluation de la CEM des émetteurs- Integrierte Schaltungen - Bewertung der
récepteurs - Partie 3: Émetteurs-récepteurs CAN elektromagnetischen Verträglichkeit von Sende-
(IEC 62228-3:2019) Empfangsgeräten - Teil 3: CAN-Sende-Empfangsgeräte
(IEC 62228-3:2019)
This European Standard was approved by CENELEC on 2019-04-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62228-3:2019 E

European foreword
The text of document 47A/1050/CDV, future edition 1 of IEC 62228-3, prepared by SC 47A "Integrated
circuits" of IEC/TC 47 "Semiconductor devices" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 62228-3:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-01-15
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-04-15
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 62228-3:2019 was approved by CENELEC as a European
Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61000-4-4 NOTE Harmonized as EN 61000-4-4
CISPR 16-1-1 NOTE Harmonized as EN 55016-1-1

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61967-1 -  Integrated circuits - Measurement of EN IEC 61967-1 -
electromagnetic emissions - Part 1: General
conditions and definitions
IEC 61967-4 -  Integrated circuits - Measurement of EN 61967-4 -
electromagnetic emissions, 150 kHz to 1 GHz -
Part 4: Measurement of conducted emissions, 1
ohm/150 ohm direct coupling method
IEC 62132-1 -  Integrated circuits - Measurement of EN 62132-1 -
electromagnetic immunity - Part 1: General
conditions and definitions
IEC 62132-4 -  Integrated circuits - Measurement of EN 62132-4 -
electromagnetic immunity 150 kHz to 1 GHz - Part
4: Direct RF power injection method
IEC 62215-3 -  Integrated circuits - Measurement of impulse EN 62215-3 -
immunity - Part 3: Non-synchronous transient
injection method
IEC 62228-1 -  Integrated circuits - EMC evaluation of EN IEC 62228-1 -
transceivers - Part 1: General conditions and
definitions
ISO 7637-2 -  Road vehicles - Electrical disturbances from - -
conduction and coupling - Part 2: Electrical
transient conduction along supply lines only
ISO 10605 -  Road vehicles - Test methods for electrical - -
disturbances from electrostatic discharge
ISO 11898-1 -  Road vehicles - Controller area network (CAN) - - -
Part 1: Data link layer and physical signalling
ISO 11898-2 -  Road vehicles - Controller area network (CAN) - - -
Part 2: High-speed medium access unit

IEC 62228-3 ®
Edition 1.0 2019-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Integrated circuits – EMC evaluation of transceivers –

Part 3: CAN transceivers
Circuits intégrés – Évaluation de la CEM des émetteurs-récepteurs –

Partie 3: Émetteurs-récepteurs CAN

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.200 ISBN 978-2-8322-6639-7

– 2 – IEC 62228-3:2019 © IEC 2019
CONTENTS
FOREWORD . 6
1 Scope . 8
2 Normative references . 8
3 Terms, definitions and abbreviated terms . 9
3.1 Terms and definitions . 9
3.2 Abbreviated terms . 10
4 General . 10
5 Test and operating conditions . 11
5.1 Supply and ambient conditions. 11
5.2 Test operation modes . 12
5.3 Test configuration . 12
5.3.1 General test configuration for transceiver network . 12
5.3.2 General test configuration for unpowered ESD test . 13
5.3.3 Transceiver network tests – Coupling ports and networks . 14
5.3.4 ESD tests – Coupling ports and networks . 15
5.4 Test signals . 16
5.4.1 General . 16
5.4.2 Test signals for normal operation mode . 16
5.4.3 Test signal for wake-up from low power mode . 18
5.5 Evaluation criteria . 22
5.5.1 General . 22
5.5.2 Evaluation criteria for functional operation modes . 22
5.5.3 Evaluation criteria in unpowered condition after exposure to
disturbances . 28
5.5.4 Status classes . 29
6 Test and measurement . 29
6.1 Emission of RF disturbances . 29
6.1.1 Test method . 29
6.1.2 Test setup . 29
6.1.3 Test procedure and parameters . 30
6.2 Immunity to RF disturbances . 31
6.2.1 Test method . 31
6.2.2 Test setup . 31
6.2.3 Test procedure and parameters . 32
6.3 Immunity to impulses . 37
6.3.1 Test method . 37
6.3.2 Test setup . 37
6.3.3 Test procedure and parameters . 38
6.4 Electrostatic discharge (ESD) . 41
6.4.1 Test method . 41
6.4.2 Test setup . 41
6.4.3 Test procedure and parameters . 43
7 Test report . 44
Annex A (normative) CAN test circuits . 45
A.1 General . 45
A.2 Test circuit for CAN transceivers for functional tests . 45

IEC 62228-3:2019 © IEC 2019 – 3 –
A.3 Test circuit for CAN transceiver for ESD test . 49
Annex B (normative) Test circuit boards. 51
B.1 Test circuit board for functional tests . 51
B.2 ESD test . 51
Annex C (informative) Examples for test limits for CAN transceiver in automotive
application . 53
C.1 General . 53
C.2 Emission of RF disturbances . 53
C.3 Immunity to RF disturbances . 54
C.4 Immunity to impulses . 57
C.5 Electrostatic discharge (ESD) . 57
Annex D (informative) Characterization of common mode choke for CAN bus
interfaces .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.