EN 61029-2-4:2003/A1:2003
(Amendment)Safety of transportable motor-operated electric tools - Part 2-4: Particular requirements for bench grinders
Safety of transportable motor-operated electric tools - Part 2-4: Particular requirements for bench grinders
Superseded by EN 61029-2-4:2011
Sicherheit transportabler motorbetriebener Elektrowerkzeuge - Teil 2-4: Besondere Anforderungen für Tischschleifmaschinen
Sécurité des machines-outils électriques semi-fixes - Partie 2-4: Règles particulières pour les tourets à meuler
Varnost premičnih električnih orodij - 2-4. del: Posebne zahteve za namizne brusilnike (IEC 61029-2-4:1993/A1:2001; spremenjen)
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 61029-2-
4:2003/A1:2004
STANDARD
marec 2004
Varnost premičnih električnih orodij - 2-4. del: Posebne zahteve za namizne
brusilnike (IEC 61029-2-4:1993/A1:2001; spremenjen)
Safety of transportable motor-operated electric tools - Part 2-4: Particular
requirements for bench grinders
ICS 25.080.50 Referenčna številka
SIST EN 61029-2-4:2003/A1:2004(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 61029-2-4/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM September 2003
ICS 25.140.20; 25.080.50
English version
Safety of transportable motor-operated electric tools
Part 2-4: Particular requirements for bench grinders
(IEC 61029-2-4:1993/A1:2001, modified)
Sécurité des machines-outils Sicherheit transportabler
électriques semi-fixes motorbetriebener Elektrowerkzeuge
Partie 2-4: Règles particulières Teil 2-4: Besondere Anforderungen
pour les tourets à meuler für Tischschleifmaschinen
(CEI 61029-2-4:1993/A1:2001, modifiée) (IEC 61029-2-4:1993/A1:2001, modifiziert)
This amendment A1 modifies the European Standard EN 61029-2-4:2003; it was approved by CENELEC
on 2003-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this amendment the status of a national standard without any
alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61029-2-4:2003/A1:2003 E
---------------------- Page: 2 ----------------------
EN 61029-2-4:2003/A1:2003 – 2 –
Foreword
The text of amendment 1:2001 to the International Standard IEC 61029-2-4:1993, prepared by
SC 61F, Safety of hand-held motor-operated electric tools, of IEC TC 61, Safety of household
and similar electrical appliances, together with the common modifications prepared by the
Technical Committee CENELEC TC 61F, Safety of hand-held and transportable motor-operated
electric tools, was submitted to the Unique Acceptance Procedure and was approved by
CENELEC as amendment A1 to EN 61029-2-4:2003 on 2003-03-01.
The following dates were fixed:
- latest date by which the amendment has to be
implemented at national level by publication of an
identical national standard or by endorsement (dop) 2004-04-01
- latest date by which the national standards conflicting
with the amendment have to be withdrawn (dow) 2006-03-01
In this document, the common modifications to the International Standard are indicated by a
vertical line in the left margin of the text.
____________
---------------------- Page: 3 ----------------------
– 3 – EN 61029-2-4:2003/A1:2003
1 Scope
1.1 Addition:
Replace the first paragraph by the following:
This International Standard applies to transportable bench grinders (Figure 101) and combined
bench grinders (Figure 107) with a wheel diameter and brush diameter not exceeding 200 mm
and a peripheral speed not exceeding 50 m/s, as defined in 2.101 and 2.114.
Add to the second paragraph:
The requirements for brushes are given in EN 1083.
Add Figure 107 as follows:
1 - straight-sided grinding wheel 7 - nozzle for dust
2 - brush 8 - on/off device
3 - flange 9 - handle
4 - work rest 10 - spark arrestor
5 - transparent screen 11 - cup shaft guard
6 - guard for straight-sided wheel 12 - marking plate
Figure 107 – Combined bench grinder
NOTE The drawings are given as a guide only.
2 Definitions
Replace definitions 2.103, 2.104 and 2.112 as follows:
2.103
tool spindle
motor spindle of the bench grinder or of the combined bench grinder which supports the brush
and/or grinding wheels and transports the rotation to them
---------------------- Page: 4 ----------------------
EN 61029-2-4:2003/A1:2003 – 4 –
2.104
nozzle for dust co
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.