EN IEC 61535:2024
(Main)Installation couplers intended for permanent connection in fixed installations
Installation couplers intended for permanent connection in fixed installations
IEC 61535:2023 is available as IEC 61535:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61535:2023 applies to two-wire, up to five-wire installation couplers, with or without earthing contact, if provided, with a rated voltage up to and including 500 V AC or 500 V DC and a rated connecting capacity up to and including 10 mm2 and a rated current not exceeding 32 A for permanent connection in electrical installations. Installation couplers with additional contacts for voltages other than mains voltages are outside the scope of this document. This third edition cancels and replaces the second edition published in 2019. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) inclusion of a definition for "live part" based on IEC 61140; b) additional optional cross medial documentation, e.g. marking with QR-Code; c) corrections on the consistent use of the expressions "earth", "earthing contact", "earthing circuit" and "protective earth(ing)" throughout the document; d) addition of missing compliance provisions to 13.3; e) update of Figure D.1 of Annex D; f) inclusion of new Annex F for cold climate requirements.
Installationssteckverbinder für dauernde Verbindung in festen Installationen
Coupleurs d'installation pour connexions permanentes dans les installations fixes
IEC 61535:2023 est disponible sous forme de IEC 61535:2023 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.L'IEC 61535:2023 s'applique aux coupleurs d'installation qui comportent deux à cinq conducteurs, avec ou sans contact de terre (le cas échéant), de tension continue ou alternative assignée jusqu'à 500 V inclus et de capacité assignée de connexion jusqu'à 10 mm2 inclus, avec un courant assigné qui ne dépasse pas 32 A, pour connexion permanente dans les installations électriques. Les coupleurs d'installation avec des contacts supplémentaires pour des tensions autres que la tension d'alimentation du réseau ne relèvent pas du domaine d'application du présent document. Cette troisième édition annule et remplace la deuxième édition parue en 2019. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) inclusion d'une définition issue de l'IEC 61140 pour "partie active"; b) documentation facultative supplémentaire disponible sur plusieurs supports, par exemple marquage avec QR code; c) corrections relatives à l'utilisation cohérente des expressions "terre", "contact de terre", "circuit de terre" et "(mise à la) terre de protection" dans l'ensemble du document; d) ajout de dispositions de conformité manquantes au 13.3; e) mise à jour de la Figure D.1 de l'Annexe D; f) ajout d'une nouvelle Annexe F pour les exigences relatives aux climats froids.
Inštalacijske spojke za trajni spoj v fiksnih napeljavah (inštalacijah)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2024
Inštalacijske spojke za trajni spoj v fiksnih napeljavah (inštalacijah)
Installation couplers intended for permanent connection in fixed installations
Installationssteckverbinder für dauernde Verbindung in festen Installationen
Coupleurs d'installation pour connexions permanentes dans les installations fixes
Ta slovenski standard je istoveten z: EN IEC 61535:2024
ICS:
29.120.99 Druga električna dodatna Other electrical accessories
oprema
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61535
NORME EUROPÉENNE
EUROPÄISCHE NORM August 2024
ICS 29.120.99 Supersedes EN IEC 61535:2019
English Version
Installation couplers intended for permanent connection in fixed
installations
(IEC 61535:2023)
Coupleurs d'installation pour connexions permanentes dans Installationssteckverbinder für dauernde Verbindung in
les installations fixes festen Installationen
(IEC 61535:2023) (IEC 61535:2023)
This European Standard was approved by CENELEC on 2024-06-12. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61535:2024 E
European foreword
The text of document 23/1062/FDIS, future edition 3 of IEC 61535, prepared by IEC/TC 23 "Electrical
accessories" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-03-12
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-06-12
document have to be withdrawn
This document supersedes EN IEC 61535:2019 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CENELEC by the
European Commission. The Standing Committee of the EFTA States subsequently approves these
requests for its Member States.
For the relationship with EU Legislation, see informative Annex ZZ, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61535:2023 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standard indicated:
IEC 60309 (series) NOTE Approved as EN IEC 60309 (series)
IEC 60320 (series) NOTE Approved as EN 60320 (series)
IEC 60364 (series) NOTE Approved as HD 60364 (series)
IEC 60364-4-41:2005 NOTE Approved as HD 60364-4-41:2017 + A11:2017
IEC 60364-5-52:2009 NOTE Approved as HD 60364-5-52:2011 + A11:2017
IEC 61995 (series) NOTE Approved as EN 61995 (series)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-2-31 2008 Environmental testing – Part 2-31: Tests - Test EN 60068-2-31 2008
Ec: Rough handling shocks, primarily for
equipment-type specimens
IEC 60112 2020 Method for determining the comparative and EN IEC 60112 2020
proof tracking indices of solid insulating
materials under moist conditions
1)
IEC 60529 – Degrees of protection provided by enclosures EN 60529 1991
(IP Code)
+ A1 2000
+ A2 2013
IEC 60664-1 2020 Insulation co-ordination for equipment within EN IEC 60664-1 2020
low-voltage systems – Part 1: Principles,
requirements and tests
1)
IEC 60695-2-11 – Fire hazard testing – Part 2-11: Glowing/hot-wire EN 60695-2-11 2021
based test methods – Glow-wire flammability
test method for end-products
1)
IEC 60998-2-3 – Connecting devices for low-voltage circuits for EN 60998-2-3 2004
household and similar purposes – Part 2-3:
Particular requirements for connecting devices
as separate entities with insulation-piercing
clamping units
IEC 60999-1 1999 Connecting devices - Electrical copper EN 60999-1 2000
conductors - Safety requirements for screw-type
and screwless-type clamping units - Part 1:
General requirements and particular
requirements for clamping units for conductors
from 0,2 mm2 up to 35 mm2 (included)
IEC 61032 1997 Protection of persons and equipment by EN 61032 1998
enclosures – Probes for verification
1)
Undated reference.
Annex ZZ
(informative)
Relationship between this European standard and the safety
objectives of Directive 2014/35/EU [2014 OJ L96] aimed to be
covered
This European standard has been prepared under a Commission’s standardisation request relating to
harmonised standards in the field of the Low Voltage Directive, M/511, to provide one voluntary means
of conforming to safety objectives of Directive 2014/35/EU of the European Parliament and of the
Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the
making available on the market of electrical equipment designed for use within certain voltage limits
[2014 OJ L96].
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZZ.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding safety objectives of
that Directive, and associated EFTA regulations.
Table ZZ.1 — Correspondence between this European standard and Annex I of Directive
2014/35/EU [2014 OJ L96]
Clause(s) / sub-clause(s)
Safety objectives of
Remarks / Notes
Directive 2014/35/EU
of this EN
(1)(a) Clauses 1, 7, 8, Annex D, Annex
E
(1)(b) Clauses 6.2, 6.3, 8.3, 8.4, 9, 11,
12, 19, 22, Annex A, Annex E
(1)(c) Clause 4
(2)(a) Clauses 9, 10, 12, 14, 16, 19.5,
20, 21, 23, Annex A
(2)(b) Clauses 11.2, 12.9, 15, 16, 17,
21.5
(2)(c) Clauses 10.1, 12, 24
(2)(d) Clauses 6, 10, 14, 21, 23, 24
(3)(a) Clauses 9.1, 12, 13, 18, 19.2,
19.3, 19.4, 20, 21.3, 21.4, 22
(3)(b) Clauses 13, 21, 24, 25, Annex F
(3)(c) Clauses 11.2, 12.2, 12.3
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
IEC 61535 ®
Edition 3.0 2023-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Installation couplers intended for permanent connection in fixed installations
Coupleurs d'installation pour connexions permanentes dans les installations
fixes
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.120.99 ISBN 978-2-8322-6700-4
– 2 – IEC 61535:2023 © IEC 2023
CONTENTS
FOREWORD . 6
INTRODUCTION . 8
1 Scope . 9
2 Normative references . 9
3 Terms and definitions . 10
4 General requirements . 12
5 Conditions for tests . 13
5.1 General . 13
5.2 Test conditions . 13
5.3 Tests on non-rewirable installation couplers . 13
5.4 Order of tests . 13
5.5 Specification of tests . 13
5.6 Compliance requirements . 13
5.7 Routine tests for non-rewirable installation couplers . 14
6 Ratings . 14
6.1 Rated voltage . 14
6.2 Rated current . 14
6.3 Rated connecting capacity . 15
6.4 Tests . 15
7 Classification . 15
8 Marking and documentation . 16
8.1 General . 16
8.2 Use of symbols or letters . 16
8.3 Markings . 16
8.4 Documentation . 17
9 Dangerous compatibility . 18
9.1 Unintended or improper connection . 18
9.2 Engagement . 18
9.3 Compatibility of different installation coupler systems . 18
9.4 Compatibility with standard systems . 18
10 Protection against electric shock . 19
10.1 Degree of protection against ingress of solid foreign objects . 19
10.2 Access to live parts . 19
10.3 External parts . 19
11 Terminals, terminations and connectable conductors . 19
11.1 Terminals and terminations . 19
11.1.1 General .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.