IEC/SC 61F - IEC_SC_61F --> TC 116

This clause of Part 1 is replaced by the following. This European Standard specifies safety requirements and their verification for the design and construction of electric powered walk-behind and hand-held lawn trimmers and lawn edge trimmers, with cutting element(s) of non metallic filament line or freely pivoting non-metallic cutter(s), with a kinetic energy of not more than 10 J each, used by a standing operator for cutting grass, their rated voltage being not more than 250 V for a.c. or 75 V d.c.. NOTE 101 The method of calculating the kinetic energy for the purposes of this standard is given in 22.103. In this European Standard, hand-held and walk-behind lawn trimmers and lawn edge trimmers are referred to collectively as machine(s). This European Standard does not apply to - scissor type or lawn trimmers and lawn edge trimmers with cutting means other than those described above; - lawn trimmers and lawn edge trimmers with collecting devices; - self-propelled lawn trimmers or lawn edge trimmers; EMC and environmental aspects, except noise, have not been considered in this European Standard. This European Standard does not apply to chargers as covered by EN 60335-2-29. This European Standard does not apply to batteries as covered by EN 62133. This European Standard deals with all the significant hazards presented by hand-held and walk-behind lawn trimmers and lawn edge trimmers when they are used as intended and under conditions of misuse which are reasonably foreseeable.

This clause of Part 1 is replaced by the following. This European Standard specifies safety requirements and their verification for the design and construction of electric powered hand-held scissors type grass shears with a maximum cutting width of 200 mm designed primarily for cutting grass, their rated voltage being not more than 250 V for a.c. or 75 V d.c. In this European Standard the term “machine” means “electric powered scissors type grass shear”. This European Standard does not apply to hedge trimmers as covered by EN 60745–2–15. Requirements for chargers are covered by EN 60335-2-29:2004. Requirements for batteries are covered by EN 62133:2003. EMC and environmental aspects except for noise have not been considered in this European Standard. This European Standard deals with all the significant hazards presented by hand-held scissors type grass shears when they are used as intended and under conditions of misuse which are reasonably foreseeable.

This European Standard specifies safety requirements and their verification for the design and construction of hand fed, shredders/chippers with integral electric motor, not exceeding 250 V single phase, with or without vacuum assisted collection which are designed to reduce organic material to smaller pieces and are used in a stationary position by an operator standing on the ground. This standard applies to shredders/chippers with feed intake openings or segments, in this standard referred to as feed safety openings that in total will fit into a square of 250 mm x 250 mm. NOTE For the requirements for the measurement of the square of 250 mm x 250 mm are given in clause 20.101.1 of this standard. In this European Standard shredders and chippers are referred to collectively as machine(s). This European Standard does not cover requirements for – machines powered by combustion engines; NOTE 1 Combustion engine driven machines are covered by EN 13683. – machines driven by an external power source or by battery power; – machines with powered discharge intended to broadcast material or load vehicles; – machines with mechanically powered feed intake or attachments; – wood chippers for agricultural, lawn and park and forestry use; NOTE 2 Wood chippers are covered by EN 13525. – machines powered from a 3 phase supply. This European Standard deals with all significant hazards presented by shredders/chippers when they are used as intended and under conditions of misuse which are reasonably foreseeable. EMC and environmental aspects, except noise, have not been considered in this European Standard. This European Standard is not applicable to machines which are manufactured before the date of publication of this document by CENELEC.

Applies to transportable planers and thicknessers with a maximum planing width of 260 mm.

IEC 60745-2-22:2011 applies to cut-off machines fitted with one bonded reinforced wheel of Type 41 or Type 42, orone or more diamond cut-off wheels with the peripheral gaps, if any, not exceeding 10 mm and with a rated speed not exceeding a peripheral speed of the wheel of 100 m/s at rated capacity and a rated wheel capacity range of 55 mm to 410 mm. These machines are intended to cut materials such as metals, concrete, masonry, glass and tile. This standard does not apply to grinders, sanders, or polishers, even if they can be converted to a cut-off machine, which are covered by IEC 60745-2-3, circular saws which are covered by IEC 60745-2-5.

IEC 61029-2-12:2010 applies to machines for creating external threads that either rotate the work piece or the cutting head.

Work initiated by IEC/SC 61F transferred to IEC/TC 116 * Ratified as A1 to EN 60745-2-13:2009 (which supersedes EN 60745-2-13:2007) with regular dates (confirmed on 2010-08-11)

Deals with the safety of pedestrian controlled mains-operated electrical cylinder or rotary lawnmowers designed primarily for use around the home or for similar purposes, their rated voltage being not more than 250 V single phase. It does not apply to lawn trimmers, lawn edge trimmers, lawn edgers, flail mowers, sickle-bar mowers, or agricultural mowers.

IEC 60745-2-17:2010 Deals with the safety of routers and trimmers which the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 440 V for three-phase a.c. tools. Supplements or modifies the corresponding clauses of IEC 60745-1. This third edition cancels and replaces the second edition published in 2003, of which it constitutes a technical revision. Main changes include: Clause 8: Marking and instructions, addition of some router specific safety warnings, clarifications in Annex K, the addition of Annex M: Safety of working stands for operation with hand-held motor-operated electric tools, and editorial modifications to match with the fourth edition of IEC 60745-1.

Amandma A1:2010 je dodatek k standardu SIST EN 60745-2-15:2009
This clause of Part 1 is applicable, except as follows: : This standard applies to hedge trimmers which are designed for use by one operator for trimming hedges and bushes, utilizing one or more linear reciprocating cutter blades. This standard is not applicable to hedge trimmers with a rotating blade.

Deals with general safety requirements of transportable motor-operated electric tools. It applies in conjunction with a part 2 for a particular type of tool. Examples of these tools are circular saws, band saws, planers, thicknessers, radial arm saws, spindle moulders, thicknessers-planers, etc.

Deals with the safety of hand-held motor-operated or magnetically driven tools, specific requirements for concrete vibrators. The rated voltage being not more than 250 V for single-phase a.c. or d.c., and 440 V for three-phase a.c. tools.

Deals with the safety of hand-held motor-operated or magnetically driven electric tools, the rated voltage of the tools being not more than 250 V for single-phase a.c. or d.c. tools, and 440 V for three-phase a.c. tools. This standard deals with the common hazards presented by hand-held tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools.

Deals with the safety of hand-held motor-operated or magnetically driven electric tools, the rated voltage of the tools being not more than 250 V for single-phase a.c. or d.c. tools, and 440 V for three-phase a.c. tools. This standard deals with the common hazards presented by hand-held tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools.

Superseded by EN 61029-1:2009

Superseded by EN 61029-1:2009

Deals with general safety requirements of transportable motor-operated electric tools. It applies in conjunction with a part 2 for a particular type of tool. Examples of these tools are circular saws, band saws, planers, thicknessers, radial arm saws, spindle moulders, thicknessers-planers, etc.

Merged with EN 60745-2-13 (pr=16377)

Merged with EN (PR=16376) at ratification (IEC, mod)

Work incorporated in IEC 60745-2-5:200X (61F/643/FDIS) / prEN 60745-2-5:200X (pr=16378) * Standstill maintained

IEC 60745-2-5:2010 deals with the safety of hand-held motor-operated or magnetically driven electric tools, specific requirements for all types of circular saws. The rated voltage being not more than 250 V for single-phase a.c. or d.c., and 440 V for three-phase a.c. tools. This standard does not apply to saws used with abrasive wheels. The principal changes in this edition as compared with the fourth edition are as follows: - clause 17 introduction of endurance tests in practical use for the guards of all types of saws; - clause 19 clarifications and editorial improvements in respect to the guarding; - annex M editorial improvements. This publication is to be read in conjunction with  IEC 60745-1:2006.

Applies to transportable diamond drills with water supply having a drill bit diameter of not more than 250 mm.

This standard applies to cutting-off grinders for cutting metal. The diameter of the plain abrasive cutting-off wheel is less than 406 mm.

Applies to transportable mitre saws intended for cutting non ferrous metals such as aluminium, wood and similar materials with a blade diameter not exceeding 400 mm. Tools comibining the function of mitre saw with the function of circular saw are not covered by this standard.

Applies to combined mitre-bench saws intended for cutting non-ferrous metals such as aluminium, wood or similar materials. The blade diameter does not exceed 350 mm.

This amendment enables EN 60745-2-8 to be read with EN 60745-1:2006 * Superseded by EN 60745-2-8:2009

This amendment enables EN 60745-2-20 to be read with EN 60745-1:2006 * Superseded by EN 60745-2-20:2009

This amendment enables EN 60745-2-1 to be read with EN 60745-1:2006 * Superseded by EN 60745-2-1:2010

This amendment enables EN 60745-2-2 to be read with EN 60745-1:2006 * Superseded by EN 60745-2-2:2010

This amendment enables EN 60745-2-6 to be read with EN 60745-1:2006 * Superseded by EN 60745-2-6:2010

This amendment enables EN 60745-2-4 to be read with EN 60745-1:2006 * Superseded by EN 60745-2-4:2009

This amendment enables EN 60745-2-11 to be read with EN 60745-1:2006 * Superseded by EN 60745-2-11:2010

This amendment enables EN 60745-2-12 to be read with EN 60745-1:2006

Superseded by EN 60745-2-9:2009

Superseded by EN 60745-2-18:2009

FprAA ratified as EN 60745-2-19:2005/A11 * Superseded by EN 60745-2-19:2009

Voted as prAA * Superseded by EN 60745-2-20:2009

Voted as prAA * Superseded by EN 60745-2-18:2009

Voted as prAB * Superseded by EN 60745-2-9:2009

Applies to chain saws for cutting wood and designed for use by one person. This standard does not cover chain saws designed for use in conjunction with a guide-plate and riving knife or in any other way such as with a support or as a stationary or transportable machine. Does not apply to chain saws for tree service as defined in ISO 11681-2, pole cutters and pruners.

Voted as prAB * Superseded by EN 60745-2-11:2010

Deals with the safety of tools which the rated voltage is not more than 250 V for single-phase a.c. or d.c. tools and 440 V for three-phase a.c. tools. Supplements or modifies the corresponding clauses of IEC 60745-1

Superseded by EN 60745-2-14:2009

Superseded by EN 60745-2-14:2009

Superseded by EN 60745-2-17:2010

Superseded by EN 60745-2-8:2009

Deals with the safety of hand-held motor-operated or magnetically driven electric tools, specific requirements for circular saws. The rated voltage being not more than 250 V for single-phase a.c. or d.c., and 440 V for three-phase a.c.tools. This standard does not apply to saws used with abrasive wheels.

Superseded by EN 60745-2-6:2010

Superseded by EN 60745-2-4:2009

Superseded by EN 60745-2-2:2010