IEC 63093-7:2018
(Main)Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 7: EER-cores
Ferrite cores - Guidelines on dimensions and the limits of surface irregularities - Part 7: EER-cores
IEC 63093-7:2018 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of EER-cores made of ferrite, the essential dimensions of coil formers to be used with them as well the effective parameter values to be used in calculations involving them, and gives guidelines on allowable limits of surface irregularities applicable to EER-cores.
This document is a specification useful in the negotiations between ferrite core manufacturers and customers about surface irregularities.
The use of “derived” standards which give more detailed specifications of component parts while still permitting compliance with this document is discussed in Annex A.
This first edition cancels and replaces the first edition of IEC 62317-7 published in 2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 62317-7:
a) IEC 63093-7 integrates IEC 62317-7 and IEC 60424-3;
b) IEC 60424-3:2015, Table 2, has been included in Annex C as Table C.1.
Noyaux ferrites – Lignes directrices relatives aux dimensions et aux limites des irrégularités de surface – Partie 7: Noyaux EER
L'IEC 63093-7:2018 spécifie les dimensions qui jouent un rôle majeur dans l'interchangeabilité mécanique d'une gamme préférentielle de noyaux EER constitués de ferrites et les dimensions essentielles des supports de bobine à utiliser avec ces noyaux, ainsi que les valeurs des paramètres effectifs à utiliser dans les calculs qui les impliquent. Elle donne également les lignes directrices relatives aux limites admissibles des irrégularités de surface applicables aux noyaux EER.
Le présent document est une spécification utile aux négociations entre les fabricants de noyaux ferrites et leurs clients concernant les irrégularités de surface.
Cette première édition annule et remplace la première édition de l'IEC 62317-7 parue en 2005. Cette édition constitue une révision technique.
Cette édition inclut les modifications techniques majeures suivantes par rapport à l'IEC 62317-7:
a) l'IEC 63093-7 intègre l'IEC 62317-7 et l'IEC 60424-3;
b) le Tableau 2 de l'IEC 60424-3:2015 a été inclus dans l'Annexe C en tant que Tableau C.1.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 63093-7 ®
Edition 1.0 2018-03
INTERNATIONAL
STANDARD
Ferrite cores – Guidelines on dimensions and the limits of surface
irregularities –
Part 7: EER-cores
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
IEC Catalogue - webstore.iec.ch/catalogue Electropedia - www.electropedia.org
The stand-alone application for consulting the entire The world's leading online dictionary of electronic and
bibliographical information on IEC International Standards, electrical terms containing 21 000 terms and definitions in
Technical Specifications, Technical Reports and other English and French, with equivalent terms in 16 additional
documents. Available for PC, Mac OS, Android Tablets and languages. Also known as the International Electrotechnical
iPad. Vocabulary (IEV) online.
IEC publications search - webstore.iec.ch/advsearchform IEC Glossary - std.iec.ch/glossary
The advanced search enables to find IEC publications by a 67 000 electrotechnical terminology entries in English and
variety of criteria (reference number, text, technical French extracted from the Terms and Definitions clause of
committee,…). It also gives information on projects, replaced IEC publications issued since 2002. Some entries have been
and withdrawn publications. collected from earlier publications of IEC TC 37, 77, 86 and
CISPR.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Customer Service Centre - webstore.iec.ch/csc
details all new publications released. Available online and If you wish to give us your feedback on this publication or
also once a month by email. need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 63093-7 ®
Edition 1.0 2018-03
INTERNATIONAL
STANDARD
Ferrite cores – Guidelines on dimensions and the limits of surface
irregularities –
Part 7: EER-cores
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.100.10 ISBN 978-2-8322-5485-1
– 2 – IEC 63093-7:2018 © IEC 2018
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Primary dimensions . 6
4.1 General . 6
4.2 Dimensions of EER-cores . 7
4.2.1 Principal dimensions . 7
4.2.2 Effective parameter and A values . 8
min
4.3 Dimensional limits for coil formers. 8
5 Limits of surface irregularities . 9
5.1 General . 9
5.2 Chips and ragged edges . 10
5.2.1 General. 10
5.2.2 Chips and ragged edges on the mating surfaces (see Figure 4) . 10
5.2.3 Chips and ragged edges on the other surfaces (see Figure 4) . 10
5.3 Cracks . 12
5.4 Flash . 12
5.5 Pull-outs . 12
5.6 Crystallites . 13
5.7 Pores . 14
Annex A (normative) Derived standards . 15
Annex B (normative) Example of dimensions for gauges to check the dimensions of
EER-cores meeting this primary standard . 16
B.1 General . 16
B.2 Procedure and requirements . 16
Annex C (informative) Examples of allowable areas of chips . 17
Bibliography . 18
Figure 1 – Dimensions of EER-cores . 7
Figure 2 – Essential dimensions of coil formers . 8
Figure 3 – Examples of surface irregularities . 9
Figure 4 – Chip locations for EER-cores . 10
Figure 5 – Cracks and pull-out locations for EER-cores . 12
Figure 6 – Crystallite location for EER-cores . 13
Figure 7 – Pore location for EER-cores . 14
Figure B.1 – Gauge dimensions . 16
Table 1 – Dimensions of EER-cores . 7
Table 2 – Effective parameter values of EER-cores . 8
Table 3 – Dimensional limits for coil formers . 9
Table 4 – Area and length reference for visual inspection . 11
Table 5 – Limits for cracks . 13
Table B.1 – Gauge dimensions . 16
Table C.1 – Allowable areas of chips for EER-cores . 17
– 4 – IEC 63093-7:2018 © IEC 2018
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FERRITE CORES – GUIDELINES ON DIMENSIONS AND
THE LIMITS OF SURFACE IRREGULARITIES –
Part 7: EER-cores
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 63093-7 has been prepared by IEC technical committee 51:
Magnetic components, ferrite and magnetic powder materials.
This first edition cancels and replaces the first edition of IEC 62317-7 published in 2005. This
edition constitutes a technical revision. This edition includes the following significant technical
changes with respect to IEC 62317-7:
a) IEC 63093-7 integrates IEC 62317-7 and IEC 60424-3;
b) IEC 60424-3:2015, Table 2, has been included in Annex C as Table C.1.
The text of this International Standard is based on the following documents:
FDIS Report on voting
51/1217/FDIS 51/1226/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts in the IEC 63093 series, published under the general title Ferrite cores –
Guidelines on dimensions and the limits of surface irregularities can be found on the IEC
website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
– 6 – IEC 63093-7:2018 © IEC 2018
FERRITE CORES – GUIDELINES ON DIMENSIONS AND
THE LIMITS OF SURFACE IRREGULARITIES –
Part 7: EER-cores
1 Scope
This part of IEC 63093 specifies the dimensions that are of importance for mechanical
interchangeability for a preferred range of EER-cores made of ferrite, the essential
dimensions of coil formers to be used with them as well the effective parameter values to be
used in calculations involving them, and gives guidelines on allowable limits of surface
irregularities applicable to EER-cores.
This document is a specification useful in the negotiations between ferrite core manufacturers
and customers about surface irregularities.
The use of “derived” standards which give more detailed specifications of component parts
while still permitting compliance with this document is di
...
IEC 63093-7 ®
Edition 1.0 2018-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Ferrite cores – Guidelines on dimensions and the limits of surface
irregularities –
Part 7: EER-cores
Noyaux ferrites – Lignes directrices relatives aux dimensions et aux limites
des irrégularités de surface –
Partie 7: Noyaux EER
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et
les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc
If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Recherche de publications IEC - Découvrez notre puissant moteur de recherche et consultez
webstore.iec.ch/advsearchform gratuitement tous les aperçus des publications. Avec un
La recherche avancée permet de trouver des publications IEC abonnement, vous aurez toujours accès à un contenu à jour
en utilisant différents critères (numéro de référence, texte, adapté à vos besoins.
comité d’études, …). Elle donne aussi des informations sur les
projets et les publications remplacées ou retirées. Electropedia - www.electropedia.org
Le premier dictionnaire d'électrotechnologie en ligne au monde,
IEC Just Published - webstore.iec.ch/justpublished
avec plus de 22 300 articles terminologiques en anglais et en
Restez informé sur les nouvelles publications IEC. Just
français, ainsi que les termes équivalents dans 19 langues
Published détaille les nouvelles publications parues.
additionnelles. Egalement appelé Vocabulaire
Disponible en ligne et une fois par mois par email.
Electrotechnique International (IEV) en ligne.
Service Clients - webstore.iec.ch/csc
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
IEC Products & Services Portal - products.iec.ch
IEC 63093-7 ®
Edition 1.0 2018-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Ferrite cores – Guidelines on dimensions and the limits of surface
irregularities –
Part 7: EER-cores
Noyaux ferrites – Lignes directrices relatives aux dimensions et aux limites
des irrégularités de surface –
Partie 7: Noyaux EER
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.100.10 ISBN 978-2-8322-1088-4
– 2 – IEC 63093-7:2018 © IEC 2018
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Primary dimensions . 6
4.1 General . 6
4.2 Dimensions of EER-cores . 7
4.2.1 Principal dimensions . 7
4.2.2 Effective parameter and A values . 8
min
4.3 Dimensional limits for coil formers. 8
5 Limits of surface irregularities . 9
5.1 General . 9
5.2 Chips and ragged edges . 10
5.2.1 General. 10
5.2.2 Chips and ragged edges on the mating surfaces (see Figure 4) . 10
5.2.3 Chips and ragged edges on the other surfaces (see Figure 4) . 10
5.3 Cracks . 12
5.4 Flash . 12
5.5 Pull-outs . 12
5.6 Crystallites . 13
5.7 Pores . 14
Annex A (normative) Derived standards . 15
Annex B (normative) Example of dimensions for gauges to check the dimensions of
EER-cores meeting this primary standard . 16
B.1 General . 16
B.2 Procedure and requirements . 16
Annex C (informative) Examples of allowable areas of chips . 17
Bibliography . 18
Figure 1 – Dimensions of EER-cores . 7
Figure 2 – Essential dimensions of coil formers . 8
Figure 3 – Examples of surface irregularities . 9
Figure 4 – Chip locations for EER-cores . 10
Figure 5 – Cracks and pull-out locations for EER-cores . 12
Figure 6 – Crystallite location for EER-cores . 13
Figure 7 – Pore location for EER-cores . 14
Figure B.1 – Gauge dimensions . 16
Table 1 – Dimensions of EER-cores . 7
Table 2 – Effective parameter values of EER-cores . 8
Table 3 – Dimensional limits for coil formers . 9
Table 4 – Area and length reference for visual inspection . 11
Table 5 – Limits for cracks . 13
Table B.1 – Gauge dimensions . 16
Table C.1 – Allowable areas of chips for EER-cores . 17
– 4 – IEC 63093-7:2018 © IEC 2018
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FERRITE CORES – GUIDELINES ON DIMENSIONS AND
THE LIMITS OF SURFACE IRREGULARITIES –
Part 7: EER-cores
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.