iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
IEC

IEC 61243-5:1997

(Main)

Live working - Voltage detectors - Part 5: Voltage detecting systems (VDS)

Live working - Voltage detectors - Part 5: Voltage detecting systems (VDS)

Is applicable to voltage detecting systems that are single-pole and are capacitively-coupled to live parts. They are used to detect the presence or absence of operating voltage on a.c. electrical systems for voltages from 1 kV to 52 kV, and for frequencies from 16 2/3 Hz to 60 Hz. This standard is also applicable to phase comparators designed for voltage detecting systems.

Travaux sous tension - Détecteurs de tension - Partie 5: Systèmes détecteurs de tension (VDS)

Est applicable aux systèmes monopolaires détecteurs de tension en couplage capacitif avec des pièces sous tension et utilisés pour détecter la présence ou l'absence de la tension de service sur les réseaux électriques de tension alternative comprise entre 1 kV et 52 kV et à des fréquences comprises entre 16 2/3 Hz et 60 Hz. Cette norme s'applique également aux comparateurs de phase conçus pour s'adapter aux système détecteurs de tension.

General Information

Status
Replaced
Publication Date
04-Jun-1997
ICS
13.260 - Protection against electric shock. Live working
29.240.20 - Power transmission and distribution lines
29.260.99 - Other electrical equipment for working in special conditions
Technical Committee
TC 78 - Live working
Drafting Committee
WG 14 - TC 78/WG 14
Current Stage
DELPUB - Deleted Publication
Completion Date
24-Jun-2021
Ref Project

Relations

Replaced By
IEC 62271-213:2021 - High-voltage switchgear and controlgear - Part 213: Voltage detecting and indicating system
Effective Date
05-Sep-2023
Replaced By
IEC 62271-215:2021 - High-voltage switchgear and controlgear - Part 215: Phase comparator used with VDIS
Effective Date
05-Sep-2023

Buy Standard

IEC 61243-5:1997 - Live working - Voltage detectors - Part 5: Voltage detecting systems (VDS)IEC 61243-5:1997 - Live working - Voltage detectors - Part 5: Voltage detecting systems (VDS)
PreviousNext
Standard
IEC 61243-5:1997 - Live working - Voltage detectors - Part 5: Voltage detecting systems (VDS)
English and French language
111 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NORME
CEI
INTERNATIONALE
IEC
61243-5
INTERNATIONAL
Première édition
STANDARD
First edition
1997-06
Travaux sous tension –
Détecteurs de tension –
Partie 5:
Systèmes détecteurs de tension (VDS)
Live working –
Voltage detectors –
Part 5:
Voltage detecting systems (VDS)
Numéro de référence
Reference number
CEI/IEC 61243-5: 1997

---------------------- Page: 1 ----------------------
Validité de la présente publication Validity of this publication
Le contenu technique des publications de la CEI est The technical content of IEC publications is kept under
constamment revu par la CEI afin qu'il reflète l'état constant review by the IEC, thus ensuring that the
actuel de la technique. content reflects current technology.
Des renseignements relatifs à la date de Information relating to the date of the reconfirmation
reconfirmation de la publication sont disponibles of the publication is available from the IEC Central
auprès du Bureau Central de la CEI. Office.
Les renseignements relatifs à ces révisions, à Information on the revision work, the issue of revised
l'établissement des éditions révisées et aux editions and amendments may be obtained from IEC
amendements peuvent être obtenus auprès des National Committees and from the following IEC
Comités nationaux de la CEI et dans les documents sources:
ci-dessous:
• Bulletin de la CEI • IEC Bulletin
• Annuaire de la CEI • IEC Yearbook
Publié annuellement Published yearly
• Catalogue des publications de la CEI • Catalogue of IEC publications
Publié annuellement et mis à jour régulièrement Published yearly with regular updates
Terminologie Terminology
En ce qui concerne la terminologie générale, le lecteur For general terminology, readers are referred to
se reportera à la CEI 60050: Vocabulaire IEC 60050: International Electrotechnical Vocabulary
Electrotechnique International (VEI), qui se présente (IEV), which is issued in the form of separate chapters
sous forme de chapitres séparés traitant chacun d'un each dealing with a specific field. Full details of the
sujet défini. Des détails complets sur le VEI peuvent IEV will be supplied on request. See also the IEC
être obtenus sur demande. Voir également le Multilingual Dictionary.
dictionnaire multilingue de la CEI.
Les termes et définitions figurant dans la présente The terms and definitions contained in the present
publication ont été soit tirés du VEI, soit publi-cation have either been taken from the IEV or
spécifiquement approuvés aux fins de cette have been specifically approved for the purpose of this
publication. publication.
Symboles graphiques et littéraux Graphical and letter symbols
Pour les symboles graphiques, les symboles littéraux For graphical symbols, and letter symbols and signs
et les signes d'usage général approuvés par la CEI, le approved by the IEC for general use, readers are
lecteur consultera: referred to publications:
– IEC 60027: Letter symbols to be used in electrical
– la CEI 60027: Symboles littéraux à utiliser en
technology;
électrotechnique;
– IEC 60417: Graphical symbols for use on
– la CEI 60417: Symboles graphiques utilisables sur
equipment. Index, survey and compilation of the
le matériel. Index, relevé et compilation des feuilles
individuelles; single sheets;
Symboles graphiques pour schémas; – IEC 60617: Graphical symbols for diagrams;
– la CEI 60617:
and for medical electrical equipment,
et pour les appareils électromédicaux,
– IEC 60878: Graphical symbols for electromedical
– la CEI 60878: Symboles graphiques pour
equipment in medical practice.
équipements électriques en pratique médicale.
Les symboles et signes contenus dans la présente The symbols and signs contained in the present
publication ont été soit tirés de la CEI 60027, de la publication have either been taken from IEC 60027,
IEC 60417, IEC 60617 and/or IEC 60878, or have
CEI 60417, de la CEI 60617 et/ou de la CEI 60878,
been specifically approved for the purpose of this
soit spécifiquement approuvés aux fins de cette
publication.
publication.
Publications de la CEI établies par le IEC publications prepared by the same
même comité d'études technical committee
The attention of readers is drawn to the end pages of
L'attention du lecteur est attirée sur les listes figurant
this publication which list the IEC publications issued
à la fin de cette publication, qui énumèrent les
by the technical committee which has prepared the
publications de la CEI préparées par le comité
present publication.
d'études qui a établi la présente publication.

---------------------- Page: 2 ----------------------
NORME
CEI
INTERNATIONALE
IEC
61243-5
INTERNATIONAL
Première édition
STANDARD
First edition
1997-06
Travaux sous tension –
Détecteurs de tension –
Partie 5:
Systèmes détecteurs de tension (VDS)
Live working –
Voltage detectors –
Part 5:
Voltage detecting systems (VDS)
 IEC 1997 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this pub
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

IEC
IEC 61318:2021(Main)
Live working - Methods for assessment of defects and verification of performance applicable to tools, devices and equipment

IEC 61318:2021 This document defines methods to assess defects and to verify that products after the manufacturer process meet the requirements of the corresponding product standard.
The principles of assessment of defects for live working products are detailed in this document to assist product standard developers in prescribing the best means to achieve suitable quality of every finished tool, device and piece of equipment.
The following elements are not covered by the present document, but are included in each product standard:
– type tests;
– provisions and description for routine, sampling and acceptance tests;
– identification and classification of defects;
– risk analysis.
This document does not cover conformity assessment of commercial shipments or certifications.
This fourth edition cancels and replaces the third edition published in 2007. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) change of the purpose of the document from a prescriptive testing standard to a standard assisting the project team in the conformance to respective product standard.
b) introduction of conformance test, record of process, quality control documentation, adapted to the standard product.
c) change of prescribed sampling procedure to adapted sampling tests to the product standard.
d) suppression of the term “conformity assessment”.
e) Introduction of the term “verification method” replacing “conformity assessment application”.

  • Standard
    33 pages
    English and French language
    sale 15% off
IEC
IEC 61243-1:2021(Main)
Live working - Voltage detectors - Part 1: Capacitive type to be used for voltages exceeding 1 kV AC

IEC 61243-1:2021 is applicable to portable voltage detectors, with or without built-in power sources, to be used on electrical systems for voltages of 1 kV to 800 kV AC, and frequencies of 50 Hz and/or 60 Hz.
This document applies only to voltage detectors of capacitive type used in contact with the bare part to be tested, as a complete device including its insulating element or as a separate device, adaptable to an insulating stick which, as a separate tool, is not covered by this document (see 4.4.2.1 for general design).
Other types of voltage detectors are not covered by this document.
Self ranging voltage detectors (formally "multi range voltage detectors") are not covered by this document.
Some restrictions or formal interdictions on their use are applicable in case of switchgear of IEC 62271 series design, due to insulation coordination, on overhead line systems of electrified railways (see Annex B) and systems without neutral reference. For systems without neutral reference, the insulating level is adapted to the maximum possible voltage to the earth (ground).
Products designed and manufactured according to this document contribute to the safety of users provided they are used by persons trained for the work, in accordance with the hot stick working method and the instructions for use.
Except where otherwise specified, all the voltages defined in this document refer to values of phase-to-phase voltages of three-phase systems. In other systems, the applicable phase-to-phase or phase-to-earth (ground) voltages are used to determine the operating voltage.
This third edition cancels and replaces the second edition published in 2003 and Amend-ment 1:2009. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) The scope is more precise, stating that only bare contact to the part to be tested is reliable for these contact voltage detectors. The rationale is that tests on painted or coated conductors have led to wrong indications, as this non-conductive paint or coat acts as a capacitor with different capacity according to the thickness. This capacity has an effect on the threshold voltage.
b) A contact probe is introduced as a new type of non-conductive contact electrode.
c) A new type "exclusively outdoor type" has been defined and implemented into the requirements and test procedure.
d) A selector for voltage and frequency is allowed if foreseeable misuse is excluded.
e) The marking for voltage detectors with low interference voltage has been made more precise.
f) The indication groups have been made more precise and requirements and tests for the "ready to operate state" and "stand-by state" added.
g) Requirements and tests for electromagnetic compatability have been implemented.
h) An example for good electrical connection for the tests is introduced.

  • Standard
    160 pages
    English and French language
    sale 15% off
IEC
IEC 60900:2018(Main)
Live working - Hand tools for use up to 1 000 V AC and 1 500 V DC

IEC 60900:2018 is available as IEC 60900:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60900:2018 is applicable to insulated, insulating and hybrid hand tools used for working live or close to live parts at nominal voltages up to 1 000 V AC and 1 500 V DC. The products designed and manufactured according to this document contribute to the safety of the users provided they are used by skilled persons, in accordance with safe methods of work and the instructions for use (where appropriate). This document has been prepared in accordance with the requirements of IEC 61477 where applicable. The products covered by this document may have an impact on the environment during some or all stages of its life cycle. These impacts can range from slight to significant, be of short term or long-term duration, and occur at the global, regional or local level. This document does not include requirements and test provisions for the manufacturers of the products, or recommendations to the users of the products for environmental improvement. This fourth edition cancels and replaces the third edition, published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) addition of a third category of tools has been added, namely hybrid hand tools;
b) introduction of a new informative Annex A on examples of insulated, insulating and hybrid hand tools.
Key words: Live Working, Insulated, Insulating, Hand Tools
The contents of the corrigendum of January 2019 and May 2020 have been included in this copy.

  • Standard
    118 pages
    English and French language
    sale 15% off
IEC
IEC TR 61328:2017(Main)
Live working - Guidelines for the installation of transmission and distribution line conductors and earth wires - Stringing equipment and accessory items

IEC TR 61328:2017(E) provides recommendations for the selection and testing where necessary of conductor stringing equipment and accessory items used for the installation of bare and insulated overhead distribution conductors, bare overhead transmission conductors and overhead earth wires. This third edition cancels and replaces the second edition published in 2003 and IEC TR 61911:2003. It incorporates some technical changes to update equipment work methods and procedures, bringing them in line with the state of the art.

  • Technical report
    73 pages
    English language
    sale 15% off
IEC
IEC 61481-1:2014(Main)
Live working - Phase comparators - Part 1: Capacitive type to be used for voltages exceeding 1 kV a.c.

IEC 61481-1:2014 is applicable to portable phase comparators of capacitive type to be used on electrical systems for voltages exceeding 1 kV a.c. and frequencies of 50 Hz and/or 60 Hz. This standard is applicable to single-pole phase comparators of capacitive type operating with a memory system up to 36 kV a.c., and two-pole phase comparators of capacitive type operating with a wireless connection up to 245 kV a.c. This standard is applicable to phase comparators of capacitive type used in contact with the bare conductive parts to be compared as a complete device including its insulating element or as a separate device, adaptable to an insulating stick which, as a separate tool, is not covered by this standard. A device that is designed to provide other functions than phase comparison is a different device and is not covered by this standard. For example a device designed to be also used as a voltage detector is not covered by this standard. This first edition, together with the first edition of IEC 61481-2, cancels and replaces the first edition of IEC 61481 published in 2001, Amendment 1:2002 and Amendment 2:2004. This edition constitutes a technical revision including the following major changes:
- split of the standard in two parts;
- extension of the scope to include two-pole phase comparators operating with a wireless connection up to 245 kV a.c.;
- review of the requirements for indication;
- introduction of a requirement for a new marking "LU" for limited use;
- and revision of existing annexes. The contents of the corrigendum of July 2015 have been included in this copy.

  • Standard
    163 pages
    English and French language
    sale 15% off
IEC
IEC 61481-2:2014(Main)
Live working - Phase comparators - Part 2: Resistive type to be used for voltages from 1kV to 36 kV a.c.

IEC 61481-2:2014 is applicable to portable phase comparators of resistive type to be used on electrical systems for voltages from 1 kV a.c. to 36 kV a.c. and frequencies of 50 Hz and/or 60 Hz. This standard is applicable to phase comparators of resistive type used in contact with the bare conductive parts to be compared as a complete device including its insulating element or as a separate device, adaptable to an insulating stick which, as a separate tool, is not covered by this standard. A device that is designed to provide other functions than phase comparison is a different device and is not covered by this standard. For example a device designed to be also used as a voltage detector is not covered by this standard. This first edition, together with the first edition of IEC 61481-1, cancels and replaces the first edition of IEC 61481 published in 2001, Amendment 1:2002 and Amendment 2:2004. This edition constitutes a technical revision which includes the following major changes:
- split of the standard in two parts;
- review of the requirements for indication;
- elimination of class C (+/- 110°);
- introduction of a requirement for a new marking "LU" for limited use;
- increase of the specified range of voltage fluctuation in a network for clear indication;
- and revision of the existing annexes.

  • Standard
    160 pages
    English and French language
    sale 15% off
IEC
IEC 61243-3:2014(Main)
Live working - Voltage detectors - Part 3: Two-pole low-voltage type

IEC 61243-3:2014 is applicable to hand-held two-pole voltage detectors with their accessories (crocodile clips and detachable leads) to be used in contact with parts of electrical systems for a.c. voltages not exceeding 1 000 V at nominal frequencies between 16 2/3 Hz and up to 500 Hz, and/or for d.c. voltages not exceeding 1 500 V. Contact electrode extensions are not covered by this standard. Voltage detectors covered by this standard are intended to be used under dry and humid conditions, both indoor and outdoor. They are not intended to be used under rain conditions. Voltage detectors covered by this standard are not intended to be used for continuous operation. Voltage detectors covered by this standard are intended to be used up to 2 000 m above sea level. This standard also includes provisions for the following supplementary functions when available:
- phase indication;
- rotating field indication;
- and continuity check. Other supplementary functions are not covered by this standard. Voltage detectors covered by this standard are not considered as measuring devices. Relevant safety requirements for measuring devices are included in IEC 61010 series. This third edition cancels and replaces the second edition published in 2009. It is a technical revision which includes the following significant technical changes with respect to the previous edition:
- requirement and test to manage interference voltages at power frequencies;
- and informative annex on voltage detectors and the presence of interference voltages.
The contents of the corrigendum of January 2015 and May 2015 have been included in this copy.

  • Standard
    152 pages
    English and French language
    sale 15% off
IEC
IEC 60984:2014(Main)
Live working - Electrical insulating sleeves

IEC 60984:2014 is applicable to electrical insulating sleeves for the protection of workers from accidental contact with live electrical conductors, apparatus or circuits. The products designed and manufactured according to this standard contribute to the safety of the users provided they are used by skilled persons, in accordance with safe methods of work and the instructions for use. Unless otherwise stated, in this standard the term "sleeve" is used for "electrical insulating sleeve". This second edition cancels and replaces the first edition, published in 1990 and its Amendment 1 published in 2002. It constitutes a technical revision which includes the following major changes:
- removal of the requirement for an area to mark the date of inspection;
- only the straight mounting method with water electrodes is specified for the dielectric type test;
- the d.c. electric tests are no longer included in the normative part of the document, but a new informative Annex E is added;
- preparation of the elements of evaluation of defects, and general application of IEC 61318:2007;
- in the new normative Annex F, updating of the characteristics of the liquid specified for tests on sleeves of category H, according to the latest edition of ISO 1817;
- introduction of a new normative Annex G on classification of defects;
- introduction of a new informative Annex H on the rationale for the classification of defects;
- and for periodic electrical retesting, recommended voltage limit of the dielectric test methods to 10 kV except in case of the test method with water electrodes and straight mounting.

  • Standard
    89 pages
    English and French language
    sale 15% off
IEC
IEC 60903:2014(Main)
Live working - Electrical insulating gloves

IEC 60903:2014 is applicable to electrical insulating gloves and mitts that provide protection of the worker against electric shock. This standard also covers electrical insulating gloves with additional integrated mechanical protection referred to in this document as "composite gloves". This third edition cancels and replaces the second edition of IEC 60903, published in 2002. It constitutes a technical revision which includes the following major changes:
- clarification of the requirements and tests for long gloves;
- introduction of a new special property for gloves resistant to leakage current;
- removal of the requirement for an area to mark the date of inspection;
- the d.c. electric tests are no longer included in the normative part of the document but a proof test is suggested at the production level in a new informative Annex E;
- preparation of the elements of evaluation of defects, and general application of IEC 61318:2007;
- introduction of a new normative Annex H on classification of defects;
- and introduction of a new informative Annex I on the rationale for the classification of defects.

  • Standard
    117 pages
    English and French language
    sale 15% off
IEC
IEC 61472:2013(Main)
Live working - Minimum approach distances for a.c. systems in the voltage range 72,5 kV to 800 kV - A method of calculation

IEC 61472:2013 describes a method for calculating the minimum approach distances for live working, at maximum voltages between 72,5 kV and 800 kV. This standard addresses system overvoltages and the working air distances or tool insulation between parts and/or workers at different electric potentials. The required withstand voltage and minimum approach distances calculated by the method described in this standard are evaluated taking into consideration
- if the workers are trained for, and skilled in, working in the live working zone;
- if the anticipated overvoltages do not exceed the value selected for the determination of the required minimum approach distance;
- if transient overvoltages are the determining overvoltages;
- if tool insulation has no continuous film of moisture or measurable contamination present on the surface;
- if no lightning is seen or heard within 10 km of the work site;
- if allowance is made for the effect of conducting components of tools; and
- if the effect of altitude, insulators in the gap, etc, on the electric strength is taken into consideration. For conditions other than the above, the evaluation of the minimum approach distances may require specific data, derived by other calculation or obtained from additional laboratory investigations on the actual situation. This third edition cancels and replaces the second edition of IEC 61472 published in 2004. It constitutes a technical revision. Significant changes with regard to the second edition are:
- the clarification of the scope;
- the review of the definitions;
- the clarification of the methodology of determining whether live working is permissible and the calculation of the minimum approach distances;
- the modification of the basic equation for calculation of the minimum approach distance; and
- the introduction of Table 1 for altitude correction factor simplification ka. The contents of the corrigendum of October 2015 have been included in this copy.

  • Standard
    90 pages
    English and French language
    sale 15% off