Nanomanufacturing - Product specifications - Part 1: Basic concepts

IEC TS 62565-1:2023 which is a Technical Specification, defines the system of blank detail specifications for nanomaterials and nano-assemblies as well as final nano-enabled products addressed in the nanomanufacturing value chain.
It defines the concepts of blank detail specification (BDS), detail specification (DS) and key control characteristic (KCC). Furthermore, it provides guidelines how to develop and use product specifications, particularly the IEC 62565 series, in the field of nanotechnology.
This document also provides guidelines regarding the certification and reliability aspects for products specified by a DS and associated KCCs.
NOTE 1 The IEC 62565 series uses an open generic structure that can be flexibly adapted to technical developments. The double indexing of the individual parts allows grouping into technology areas without restriction due to an overly strict hierarchical structure.
NOTE 2 Key elements of the IEC 62565 series are a consensus-based set of key control characteristics (KCCs) with clear definitions and standardized measurement procedures to measure them.

General Information

Status
Published
Publication Date
10-May-2023
Current Stage
PPUB - Publication issued
Start Date
20-Jun-2023
Completion Date
11-May-2023
Ref Project

Buy Standard

Technical specification
IEC TS 62565-1:2023 - Nanomanufacturing - Product specifications - Part 1: Basic concepts Released:5/11/2023
English language
29 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


IEC TS 62565-1 ®
Edition 1.0 2023-05
TECHNICAL
SPECIFICATION
colour
inside
Nanomanufacturing – Product specifications –
Part 1: Basic concepts
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews. With a subscription you will always have
committee, …). It also gives information on projects, replaced access to up to date content tailored to your needs.
and withdrawn publications.
Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
The world's leading online dictionary on electrotechnology,
Stay up to date on all new IEC publications. Just Published
containing more than 22 300 terminological entries in English
details all new publications released. Available online and once
and French, with equivalent terms in 19 additional languages.
a month by email.
Also known as the International Electrotechnical Vocabulary

(IEV) online.
IEC Customer Service Centre - webstore.iec.ch/csc

If you wish to give us your feedback on this publication or need
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC TS 62565-1 ®
Edition 1.0 2023-05
TECHNICAL
SPECIFICATION
colour
inside
Nanomanufacturing – Product specifications –

Part 1: Basic concepts
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 07.120 ISBN 978-2-8322-7020-2

– 2 – IEC TS 62565-1:2023  IEC 2023
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 8
4 General . 12
4.1 Requirements for product specifications . 12
4.2 Generic systematics of specifications for nanomaterials and nano-enabled
products . 12
4.3 Blank detail specification . 13
4.4 Detail specification . 14
5 Structure of a blank detail specification . 15
5.1 General . 15
5.2 General product description and procurement information . 15
5.3 Specification of key control characteristics . 16
6 Measurement procedures for key control characteristics . 17
6.1 General . 17
6.2 SML 4: Standardized measurement procedure for the KCC available . 17
6.3 SML 3: Adoption and adaptation of an existing standardized measurement
procedure . 17
6.4 SML 2: Guidance for measurement procedures in the absence of a standard . 17
6.5 SML 1: No documented measurement procedure available . 18
6.6 Overview of measurement methods and SML of the related measurement
procedures . 18
7 Certification aspects . 19
7.1 General remarks . 19
7.2 Product audit . 20
7.3 Factory audit . 20
8 Process steps for the development of nanomaterial or nano-enabled product detail
specification . 20
8.1 General . 20
8.2 Defining the scope of the specification . 20
8.3 Defining the list of key control characteristics. 21
Annex A (informative) Structure of standards for blank detail specifications . 22
A.1 Title and scope of standards for blank detail specifications . 22
A.1.1 Generic format of the title . 22
A.1.2 Generic format of the scope . 22
A.2 Content of standards for blank detail specifications . 22
Annex B (informative) Structure of measurement standards for key control
characteristics . 24
B.1 Title and scope of measurement standards for key control characteristics. 24
B.1.1 Generic format of the title . 24
B.1.2 Generic format of the scope . 24
B.2 Content of measurement standards for key control characteristics . 24
Annex C (informative) Guidance of quality evaluation and reliability assessment . 26
C.1 General . 26
C.2 Content of quality and reliability assessment standard . 26

C.3 QM system audit . 27
C.4 Process audit . 27
C.5 Product audit . 27
C.6 Audit score . 27
C.7 Audit frequency . 28
C.8 Environmental, health and safety (EHS) aspects . 28
Bibliography . 29

Figure 1 – Systematics of IEC TC 113 standards . 6
Figure 2 – KCCs and their relation to the BDS: general scheme . 14
Figure 3 – KCCs and their relation to the BDS: example . 14

Table 1 – General product description and procurement information . 15
Table 2 – Format for specification of key control characteristics . 16
Table 3 – Overview of measurement methods (Example) . 19

– 4 – IEC TS 62565-1:2023  IEC 2023
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
NANOMANUFACTURING –
PRODUCT SPECIFICATIONS –
Part 1: Basic concepts
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC TS 62565-1 has been prepared by IEC technical committee 113: Nanotechnology for
electrotechnical products and systems. It is a Technical Specification.
The text of this Technical Specification is based on the following documents:
Draft Report on voting
113/697/DTS 113/723/RVDTS
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this Technical Specification is English.

This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/publications.
A list of all parts in the IEC 62565 series, published under the general title Nanomanufacturing –
Product specifications, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under web
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.