ISO 7638-2:2018

Road vehicles — Connectors for the electrical connection of towing and towed vehicles — Part 2: Connectors for braking systems and running gear of vehicles with 12 V nominal supply voltage

This part of ISO 7638 gives the dimensions of, and specifies the contact allocation and tests and test requirements for, connectors for the electrical connection of the braking systems and running gear of towing and towed vehicles with 12 V nominal supply voltage. In addition, it specifies a park socket used to receive and store the plug when disconnected.

Véhicules routiers — Connecteurs pour liaisons électriques entre véhicules tracteurs et véhicules tractés — Partie 2: Connecteurs pour les équipements de freinage et les organes de roulement des véhicules à tension nominale de 12 V

General Information

• Status: Published
• Publication Date: 16-May-2018
• ICS: 43.040.10 - Electrical and electronic equipment
• ICS: 43.040.40 - Braking systems
• Technical Committee: ISO/TC 22/SC 32 - Electrical and electronic components and general system aspects
• Drafting Committee: ISO/TC 22/SC 32/WG 9 - Electrical connections between towing and towed vehicles
• Current Stage: 9060 - Close of review
• Start Date: 02-Dec-2028

Relations

• Revises: ISO 7638-2:2003 - Road vehicles — Connectors for the electrical connection of towing and towed vehicles — Part 2: Connectors for braking systems and running gear of vehicles with 12 V nominal supply voltage
• Effective Date: 23-Jan-2016

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7638-2
Third edition
2018-05
Road vehicles — Connectors for the
electrical connection of towing and
towed vehicles —
Part 2:
Connectors for braking systems and
running gear of vehicles with 12 V
nominal supply voltage
Véhicules routiers — Connecteurs pour liaisons électriques entre
véhicules tracteurs et véhicules tractés —
Partie 2: Connecteurs pour les équipements de freinage et les organes
de roulement des véhicules à tension nominale de 12 V
Reference number
ISO 7638-2:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 7638-2:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7638-2:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensional characteristics . 1
4.1 General . 1
4.2 Plug . 2
4.3 Socket . 2
4.4 Park socket . 2
5 Application of the connector . 2
5.1 General . 2
5.2 Contact allocation . 6
5.3 Contact designation . 7
5.4 Terminals . 7
5.5 Connecting cable . 7
6 Tests and specific requirements . 7
6.1 General . 7
6.2 Mismating . 8
6.3 Connection and disconnection . 8
6.4 Endurance . 8
© ISO 2018 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 7638-2:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
Subcommittee
This document was prepared by Technical Committee ISO/TC 22, Road vehicles, SC 32,
Electrical and electronic components and general system aspects.
This third edition cancels and replaces the second edition (ISO 7638-2:2003), which has been technically
revised. The main changes compared to the previous edition are as follows:
— corrected figures.
A list of all parts in the ISO 7638 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 7638-2:2018(E)
...