ISO 7617-2:2003

Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics

ISO 7617-2:2003 specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a woven cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings are known as poly(vinyl chloride) (PVC) coatings. The present specification covers two grades (A and B) of PVC-coated woven fabric.

Supports textiles revêtus de plastique pour ameublement et garniture — Partie 2: Spécifications pour les tissus revêtus de PVC

General Information

• Status: Published
• Publication Date: 18-Aug-2003
• ICS: 59.080.40 - Coated fabrics
• ICS: 97.140 - Furniture
• Technical Committee: ISO/TC 45/SC 4 - Products (other than hoses)
• Drafting Committee: ISO/TC 45/SC 4/WG 13 - Coated fabrics
• Current Stage: 9092 - International Standard to be revised
• Completion Date: 05-Apr-2024

Relations

• Revises: ISO 7617-2:1994 - Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics
• Effective Date: 15-Apr-2008

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7617-2
Third edition
2003-08-01
Plastics-coated fabrics for upholstery —
Part 2:
Specification for PVC-coated woven
fabrics
Supports textiles revêtus de plastique pour ameublement et garniture —
Partie 2: Spécifications pour les tissus revêtus de PVC

Reference number
ISO 7617-2:2003(E)
©
ISO 2003

---------------------- Page: 1 ----------------------
ISO 7617-2:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
©
ii ISO 2003 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7617-2:2003(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Technical requirements . 1
4 Sampling . 2
5 Testing and compliance . 2
6 Marking . 3
Annex A (normative) Method of selecting test specimens . 4
Annex B (normative) Determination of resistance to print wear . 6
Annex C (normative) Determination of colour fastness to rubbing . 8
©
ISO 2003 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 7617-2:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7617-2 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 4, Products (other than hoses).
This third edition cancels and replaces the second edition (ISO 7617-2:1994), which has been technically
revised.
ISO 7617 consists of the following parts, under the general title Plastics-coated fabrics for upholstery:
— Part 1: Specification for
...