Paints and varnishes — Determination of resistance to abrasion — Part 2: Method with abrasive rubber wheels and rotating test specimen

This document specifies a method for determining the resistance to abrasion of coatings, for which two loaded, freely rotatable but eccentrically arranged abrasive rubber wheels affect the coating of the rotating test specimen.

Peintures et vernis — Détermination de la résistance à l'abrasion — Partie 2: Méthode utilisant des roues abrasives en caoutchouc et une éprouvette rotative

Le présent document spécifie une méthode permettant de déterminer la résistance à l’abrasion des revêtements en appliquant deux roues abrasives en caoutchouc qui sont chargées et qui tournent librement, mais de manière excentrée sur le revêtement de l’éprouvette rotative.

General Information

Status
Published
Publication Date
02-Feb-2023
Current Stage
6060 - International Standard published
Start Date
03-Feb-2023
Due Date
30-Jun-2024
Completion Date
03-Feb-2023
Ref Project

Relations

Buy Standard

Standard
ISO 7784-2:2023 - Paints and varnishes — Determination of resistance to abrasion — Part 2: Method with abrasive rubber wheels and rotating test specimen Released:2/3/2023
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 7784-2:2023 - Peintures et vernis — Détermination de la résistance à l'abrasion — Partie 2: Méthode utilisant des roues abrasives en caoutchouc et une éprouvette rotative Released:2/3/2023
French language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
REDLINE ISO/FDIS 7784-2 - Paints and varnishes — Determination of resistance to abrasion — Part 2: Method with abrasive rubber wheels and rotating test specimen Released:12. 10. 2022
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 7784-2 - Paints and varnishes — Determination of resistance to abrasion — Part 2: Method with abrasive rubber wheels and rotating test specimen Released:12. 10. 2022
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 7784-2 - Paints and varnishes — Determination of resistance to abrasion — Part 2: Method with abrasive rubber wheels and rotating test specimen Released:8. 11. 2022
French language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7784-2
Third edition
2023-02
Paints and varnishes — Determination
of resistance to abrasion —
Part 2:
Method with abrasive rubber wheels
and rotating test specimen
Peintures et vernis — Détermination de la résistance à l'abrasion —
Partie 2: Méthode utilisant des roues abrasives en caoutchouc et une
éprouvette rotative
Reference number
ISO 7784-2:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 7784-2:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7784-2:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus and materials .3
6 Test specimens . 5
6.1 Preparation of test specimens . 5
6.2 Film thickness . 5
6.3 Conditioning. 5
7 Procedure .5
7.1 Agreements . 5
7.2 Preparation of the abrasive wheels . 5
7.3 Test conditions . 6
7.4 Number of determinations . 6
7.5 Test procedure . 6
8 Ev a luat ion . 6
9 Precision . 6
10 Test report . 7
Bibliography . 8
iii
© ISO 2023 – All rights reserved

---------------------- Page: 3 ----------------------
ISO 7784-2:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139 Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 7784-2:2016), which has been technically
revised.
The main changes are as follows:
— Figures 1 and 2 have been updated;
— some measures in 5.1.4, 5.2 and in the note to 5.3 have been updated;
— the text has been editorially revised and the normative references have been updated.
A list of all parts in the ISO 7784 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2023 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 7784-2:2023(E)
Introduction
This document is one of the three parts of ISO 7784 dealing with test methods for the determination
of the resistance to abrasion of coatings using abrasive wheels. The characteristics and differences of
these methods are summarized in Table 1.
Table 1 — Types of method
Abrasive wheel
Test specimen
Standard
movement
Type Degree of freedom
Abrasive paper on
ISO 7784-1
rubber wheel
Freely rotatable Rotation
ISO 7784-2 Abrasive rubber wheel
Rigid – with
Abrasive paper on
ISO 7784-3 stroke-dependent Linear reciprocation
metal wheel
a
rotation
a
A mechanism rotates the abrasive wheel by a small angle after each double stroke so that a new area of the abrasive
paper is effective.
It is preferable that the methods using abrasive-paper covered wheels (in ISO 7784-1 and ISO 7784-3)
are applied.
v
© ISO 2023 – All rights reserved

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 7784-2:2023(E)
Paints and varnishes — Determination of resistance to
abrasion —
Part 2:
Method with abrasive rubber wheels and rotating test
specimen
1 Scope
This document specifies a method for determining the resistance to abrasion of coatings, for which
two loaded, freely rotatable but eccentrically arranged abrasive rubber wheels affect the coating of the
rotating test specimen.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1514, Paints and varnishes — Standard panels for testing
ISO 2808, Paints and varnishes — Determination of film thickness
ISO 3270, Paints and varnishes and their raw materials — Temperatures and humidities for conditioning
and testing
ISO 4618, Paints and varnishes — Terms and definitions
ISO 48-4, Rubber, vulcanized or thermoplastic — Determination of hardness — Part 4: Indentation
hardness by durometer method (Shore hardness)
ISO 48-5, Rubber, v
...

NORME ISO
INTERNATIONALE 7784-2
Troisième édition
2023-02
Peintures et vernis — Détermination
de la résistance à l'abrasion —
Partie 2:
Méthode utilisant des roues abrasives
en caoutchouc et une éprouvette
rotative
Paints and varnishes — Determination of resistance to abrasion —
Part 2: Method with abrasive rubber wheels and rotating test
specimen
Numéro de référence
ISO 7784-2:2023(F)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 7784-2:2023(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2023
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
  © ISO 2023 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 7784-2:2023(F)
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application .1
2 Références normatives .1
3 Termes et définitions . 1
4 Principe. 2
5 Appareillage et matériels .3
6 Éprouvettes. 5
6.1 Préparation des éprouvettes . 5
6.2 Épaisseur de feuil . 5
6.3 Conditionnement . 5
7 Mode opératoire . 5
7.1 Accords . 5
7.2 Préparation des roues abrasives . 6
7.3 Conditions d'essai . 6
7.4 Nombre de déterminations . 6
7.5 Mode opératoire d'essai. 6
8 Évaluation . 6
9 Fidélité . 7
10 Rapport d’essai . 7
Bibliographie . 8
iii
© ISO 2023 – Tous droits réservés

---------------------- Page: 3 ----------------------
ISO 7784-2:2023(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 35, Peintures et vernis, sous-
comité SC 9, Méthodes générales d’essai des peintures et vernis, en collaboration avec le comité technique
CEN/TC 139, Peintures et vernis, du Comité européen de normalisation (CEN) conformément à l'Accord
de coopération technique entre l'ISO et le CEN (Accord de Vienne).
Cette troisième édition annule et remplace la deuxième édition (ISO 7784-2:2016) qui a fait l’objet d’une
révision technique.
Les principales modifications sont les suivantes:
— les Figures 1 et 2 ont été mises à jour;
— certaines mesures en 5.1.4, en 5.2 et dans la note en 5.3 ont été mises à jour;
— le texte a fait l’objet de modifications rédactionnelles et les références normatives ont été mises à
jour.
Une liste de toutes les parties de la série ISO 7784 peut être consultée sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www.iso.org/fr/members.html.
iv
  © ISO 2023 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 7784-2:2023(F)
Introduction
Le présent document constitue l’une des trois parties de l’ISO 7784 traitant des méthodes d’essai
utilisées pour la détermination de la résistance à l’abrasion des revêtements au moyen de roues
abrasives. Les caractéristiques de ces méthodes et leurs différences sont résumées dans le Tableau 1.
Tableau 1 — Types de méthode
Roue abrasive
Mouvement de l’éprou-
Norme
vette
Type Degré de liberté
Papier abrasif sur roue en
ISO 7784-1
caoutchouc
Rotation libre Rotation
Roue abrasive en caout-
ISO 7784-2
chouc
Papier abrasif sur roue Rigide – avec une rotation Mouvement de va-et-vient
ISO 7784-3
a
métallique dépendant de la course linéaire
a
Un mécanisme fait tourner la roue abrasive d’un petit angle après chaque va-et-vient de manière à faire apparaître une
surface non utilisée de papier abrasif.
Il est préférable d'appliquer les méthodes utilisant des roues revêtues de papier abrasif (dans l'ISO 7784-1
et l'ISO 7784-3).
v
© ISO 2023 – Tous droits réservés

---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 7784-2:2023(F)
Peintures et vernis — Détermination de la résistance à
l'abrasion —
Partie 2:
Méthode utilisant des roues abrasives en caoutchouc et
une éprouvette rotative
1 Domaine d'application
Le présent document spécifie une méthode permettant de déterminer la résistance à l’abrasion des
revêtements en appliquant deux roues abrasives en caoutchouc qui sont chargées et qui tournent
librement, mais de manière excentrée sur le revêtement de l’éprouvette rotative.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s'applique (y compris les
éventuels amendements).
ISO 1514, Peintures et vernis — Panneaux normalisés pour essai
ISO 2808, Peintures et vernis — Détermination de l'épaisseur du feuil
ISO 3270, Peintures et vernis et leurs matières premières — Températures et humidités pour le
conditionnement et l'essai
ISO 4618, Peintures et vernis — Termes et définitions
ISO 48-4, Caoutchouc vulcanisé ou thermoplastique — Détermination de la dureté — Partie 4: Dureté par
pénétration par la méthode au duromètre (dureté Shore)
ISO 48-5, Caoutchouc vulcanisé ou thermoplastique — Détermin
...

Style Definition: Heading 1: Indent: Left: 0 pt, First
ISO/DISFDIS 7784--2:2022(E)
line: 0 pt, Tab stops: Not at 21.6 pt
ISO TC 35/SC 9/WG 31 Style Definition: Heading 2: Font: Bold, Tab stops: Not
at 18 pt
Date: 2022-03-0310-11 Style Definition: Heading 3: Font: Bold
Style Definition: Heading 4: Font: Bold
Paints and varnishes — Determination of resistance to abrasion — Part 2:
Style Definition: Heading 5: Font: Bold
Method with abrasive rubber wheels and rotating test specimen
Style Definition: Heading 6: Font: Bold
Style Definition: ANNEX
Peintures et vernis — Détermination de la résistance à l'abrasion — Partie 2:
Style Definition: zzCopyright
Méthode utilisant des roues abrasives en caoutchouc et une éprouvette rotative
Style Definition: AMEND Terms Heading: Font: Bold
Style Definition: AMEND Heading 1 Unnumbered:
Font: Bold
Formatted: German (Germany)
Formatted: German (Germany)

---------------------- Page: 1 ----------------------
ISO/DISFDIS 7784-2:2022(E)
© ISO 2022
Formatted: Indent: Left: 0 pt, Right: 0 pt, Space
Before: 0 pt, No page break before, Adjust space
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no between Latin and Asian text, Adjust space between
part of this publication may be reproduced or utilized otherwise in any form or by any means, Asian text and numbers
electronic or mechanical, including photocopying, or posting on the internet or an intranet, without
Formatted: Default Paragraph Font
prior written permission. Permission can be requested from either ISO at the address below or
Formatted: Default Paragraph Font
ISO’sISO's member body in the country of the requester.
ISO copyright officeCopyright Office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Formatted: Indent: Left: 0 pt, First line: 0 pt, Right: 0
pt, Adjust space between Latin and Asian text, Adjust
Phone: + 41 22 749 01 11
space between Asian text and numbers
Email: copyright@iso.org
Email: copyright@iso.org
Website: www.iso.orgwww.iso.org
Formatted: English (United Kingdom)
Formatted: Indent: Left: 0 pt, First line: 0 pt, Right: 0
Published in Switzerland.
pt, Adjust space between Latin and Asian text, Adjust
space between Asian text and numbers
Formatted: English (United Kingdom)
Formatted: English (United Kingdom)
ii © ISO 2022 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DISFDIS 7784-2:2022(E)
Contents
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus and materials . 2
6 Test specimens . 4
6.1 Preparation of test specimens . 4
6.2 Film thickness . 4
6.3 Conditioning . 4
7 Procedure . 4
7.1 Agreements . 4
7.2 Preparation of the abrasive wheels . 5
7.3 Test conditions . 5
7.4 Number of determinations . 5
7.5 Test procedure . 5
8 Evaluation . 5
9 Precision . 6
10 Test report . 6
Bibliography . 7
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus and materials . 3
6 Test specimens . 5
6.1 Preparation of test specimens . 5
6.2 Film thickness . 6
6.3 Conditioning . 6
7 Procedure . 6
7.1 Agreements . 6
7.2 Preparation of the abrasive wheels . 6
7.3 Test conditions . 6
7.4 Number of determinations . 6
7.5 Test procedure . 6
8 Evaluation . 7
© ISO 2022 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/DISFDIS 7784-2:2022(E)
9 Precision . 7
10 Test report . 7
Bibliography . 9

iv © ISO 2022 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/DISFDIS 7784-2:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directiveswww.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patentswww.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the World
Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.htmlwww.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC
Formatted: English (United Kingdom)
9, General test methods for paints and varnishes, in collaboration with the European Committee for
Formatted: Don't adjust space between Latin and
Standardization (CEN) Technical Committee CEN/TC 139 Paints and varnishes, in accordance with the
Asian text, Don't adjust space between Asian text and
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
numbers
Formatted: English (United Kingdom)
This third edition cancels and replaces the second edition (ISO 7784-2:2016), which has been technically
revised. Formatted: Font: Not Italic, English (United Kingdom)
Formatted: English (United Kingdom)
The main changes are as follows:
Formatted: Font: Not Italic, English (United Kingdom)
— Figures 1 and 2 have been updated;
Formatted: English (United Kingdom)
Formatted: Font: Not Italic, English (United Kingdom)
— some measures in 5.1.4, 5.2 and in the note to 5.3 have been updated;
Formatted: English (United Kingdom)
— the text has been editorially revised and the normative references have been updated.
Formatted: cite_sec
A list of all parts in the ISO 7784 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at
www.iso.org/members.htmlwww.iso.org/members.html.
© ISO 2022 – All rights reserved v

---------------------- Page: 5 ----------------------
ISO/DISFDIS 7784-2:2022(E)
Introduction
This document is one of the three parts of ISO 7784 dealing with test methods for the determination of
the resistance to abrasion of coatings using abrasive wheels. The characteristics and differences of these
methods are summarized in Table 1.
Table 1 — Types of method
Table 1 — Types of method
Abrasive wheel
Test specimen
Standard
movement
Type Degree of freedom
Abrasive paper on
ISO 7784--1
Formatted: Left
rubber wheel
Freely rotatable Rotation
ISO 7784--2 Abrasive rubber wheel
Formatted: Left
Rigid – with
Abrasive paper on
ISO 7784--3 stroke-dependent Linear reciprocation
Formatted: Left
metal wheel
a
rotation
a
  A mechanism rotates the abrasive wheel by a small angle after each
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 7784-2
ISO/TC 35/SC 9
Paints and varnishes — Determination
Secretariat: BSI
of resistance to abrasion —
Voting begins on:
2022-10-26
Part 2:
Voting terminates on:
Method with abrasive rubber wheels
2022-12-21
and rotating test specimen
Peintures et vernis — Détermination de la résistance à l'abrasion —
Partie 2: Méthode utilisant des roues abrasives en caoutchouc et une
éprouvette rotative
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 7784-2:2022(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2022

---------------------- Page: 1 ----------------------
ISO/FDIS 7784-2:2022(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 7784-2
ISO/TC 35/SC 9
Paints and varnishes — Determination
Secretariat: BSI
of resistance to abrasion —
Voting begins on:
Part 2:
Voting terminates on:
Method with abrasive rubber wheels
and rotating test specimen
Peintures et vernis — Détermination de la résistance à l'abrasion —
Partie 2: Méthode utilisant des roues abrasives en caoutchouc et une
éprouvette rotative
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
ISO/CEN PARALLEL PROCESSING
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: +41 22 749 01 11
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: copyright@iso.org
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 7784-2:2022(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2022 – All rights reserved
NATIONAL REGULATIONS. © ISO 2022

---------------------- Page: 2 ----------------------
ISO/FDIS 7784-2:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus and materials .3
6 Test specimens . 5
6.1 Preparation of test specimens . 5
6.2 Film thickness . 5
6.3 Conditioning. 5
7 Procedure .5
7.1 Agreements . 5
7.2 Preparation of the abrasive wheels . 5
7.3 Test conditions . 6
7.4 Number of determinations . 6
7.5 Test procedure . 6
8 Ev a luat ion . 6
9 Precision . 6
10 Test report . 7
Bibliography . 8
iii
© ISO 2022 – All rights reserved

---------------------- Page: 3 ----------------------
ISO/FDIS 7784-2:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 139 Paints and varnishes, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 7784-2:2016), which has been technically
revised.
The main changes are as follows:
— Figures 1 and 2 have been updated;
— some measures in 5.1.4, 5.2 and in the note to 5.3 have been updated;
— the text has been editorially revised and the normative references have been updated.
A list of all parts in the ISO 7784 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2022 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/FDIS 7784-2:2022(E)
Introduction
This document is one of the three parts of ISO 7784 dealing with test methods for the determination
of the resistance to abrasion of coatings using abrasive wheels. The characteristics and differences of
these methods are summarized in Table 1.
Table 1 — Types of method
Abrasive wheel
Test specimen
Standard
movement
Type Degree of freedom
Abrasive paper on
ISO 7784-1
rubber wheel
Freely rotatable Rotation
ISO 7784-2 Abrasive rubber wheel
Rigid – with
Abrasive paper on
ISO 7784-3 stroke-dependent Linear reciprocation
metal wheel
a
rotation
a
A mechanism rotates the abrasive wheel by a small angle after each double stroke so that a new area of the abrasive
paper is effective.
It is preferable that the methods using abrasive-paper covered wheels (in ISO 7784-1 and ISO 7784-3)
are applied.
v
© ISO 2022 – All rights reserved

---------------------- Page: 5 ----------------------
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 7784-2:2022(E)
Paints and varnishes — Determination of resistance to
abrasion —
Part 2:
Method with abrasive rubber wheels and rotating test
specimen
1 Scope
This document specifies a method for determining the resistance to abrasion of coatings, for which
two loaded, freely rotatable but eccentrically arranged abrasive rubber wheels affect the coating of the
rotating test specimen.
2 Normative references
T
...

PROJET
NORME ISO/FDIS
FINAL
INTERNATIONALE 7784-2
ISO/TC 35/SC 9
Peintures et vernis — Détermination
Secrétariat: BSI
de la résistance à l'abrasion —
Début de vote:
2022-10-26
Partie 2:
Vote clos le:
Méthode utilisant des roues abrasives
2022-12-21
en caoutchouc et une éprouvette
rotative
Paints and varnishes — Determination of resistance to abrasion —
Part 2: Method with abrasive rubber wheels and rotating test
specimen
TRAITEMENT PARALLÈLE ISO/CEN
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSER-
VATIONS, NOTIFICATION DES DROITS DE PRO-
PRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT
CONNAISSANCE ET À FOURNIR UNE DOCUMEN-
TATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-
Numéro de référence
MERCIALES, AINSI QUE DU POINT DE VUE
ISO/FDIS 7784-2:2022(F)
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
CONSIDÉRÉS DU POINT DE VUE DE LEUR POSSI-
BILITÉ DE DEVENIR DES NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTA-
TION NATIONALE. © ISO 2022

---------------------- Page: 1 ----------------------
ISO/FDIS 7784-2:2022(F)
PROJET
NORME ISO/FDIS
FINAL
INTERNATIONALE 7784-2
ISO/TC 35/SC 9
Peintures et vernis — Détermination
Secrétariat: BSI
de la résistance à l'abrasion —
Début de vote:
2022-10-26
Partie 2:
Vote clos le:
Méthode utilisant des roues abrasives
2022-12-21
en caoutchouc et une éprouvette
rotative
Paints and varnishes — Determination of resistance to abrasion —
Part 2: Method with abrasive rubber wheels and rotating test
specimen
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2022
TRAITEMENT PARALLÈLE ISO/CEN
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
LES DESTINATAIRES DU PRÉSENT PROJET SONT
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
INVITÉS À PRÉSENTER, AVEC LEURS OBSER-
VATIONS, NOTIFICATION DES DROITS DE PRO-
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
PRIÉTÉ DONT ILS AURAIENT ÉVENTUELLEMENT
ISO copyright office
CONNAISSANCE ET À FOURNIR UNE DOCUMEN-
TATION EXPLICATIVE.
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
Tél.: +41 22 749 01 11
INDUSTRIELLES, TECHNOLOGIQUES ET COM-
Numéro de référence
E-mail: copyright@iso.org
MERCIALES, AINSI QUE DU POINT DE VUE
ISO/FDIS 7784-2:2022(F)
Web: www.iso.org
DES UTILISATEURS, LES PROJETS DE NORMES
INTERNATIONALES DOIVENT PARFOIS ÊTRE
Publié en Suisse
CONSIDÉRÉS DU POINT DE VUE DE LEUR POSSI-
BILITÉ DE DEVENIR DES NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTA-
ii
  © ISO 2022 – Tous droits réservés
TION NATIONALE. © ISO 2022

---------------------- Page: 2 ----------------------
ISO/FDIS 7784-2:2022(F)
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application .1
2 Références normatives .1
3 Termes et définitions . 1
4 Principe. 2
5 Appareillage et matériels .3
6 Éprouvettes. 5
6.1 Préparation des éprouvettes . 5
6.2 Épaisseur de feuil . 5
6.3 Conditionnement . 5
7 Mode opératoire . 5
7.1 Accords . 5
7.2 Préparation des roues abrasives . 6
7.3 Conditions d'essai . 6
7.4 Nombre de déterminations . 6
7.5 Mode opératoire d'essai. 6
8 Évaluation . 6
9 Fidélité . 7
10 Rapport d’essai . 7
Bibliographie . 8
iii
© ISO 2022 – Tous droits réservés

---------------------- Page: 3 ----------------------
ISO/FDIS 7784-2:2022(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document
a été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété. Les détails concernant les références aux droits
de propriété intellectuelle ou autres droits analogues identifiés lors de l'élaboration du document
sont indiqués dans l'Introduction et/ou dans la liste des déclarations de brevets reçues par l'ISO
(voir www.iso.org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir le lien suivant: www.iso.org/iso/avant-propos.html.
Le présent document a été élaboré par le comité technique ISO/TC 35, Peintures et vernis, sous-
comité SC 9, Méthodes générales d’essai des peintures et vernis, en collaboration avec le comité technique
CEN/TC 139, Peintures et vernis, du Comité européen de normalisation (CEN) conformément à l'Accord
de coopération technique entre l'ISO et le CEN (Accord de Vienne).
Cette troisième édition annule et remplace la deuxième édition (ISO 7784-2:2016) qui a fait l’objet d’une
révision technique.
Les principales modifications sont les suivantes:
— les Figures 1 et 2 ont été mises à jour;
— certaines mesures en 5.1.4, en 5.2 et dans la note en 5.3 ont été mises à jour;
— le texte a fait l’objet de modifications rédactionnelles et les références normatives ont été mises à
jour.
Une liste de toutes les parties de la série ISO 7784 peut être consultée sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www.iso.org/members.html.
iv
  © ISO 2022 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO/FDIS 7784-2:2022(F)
Introduction
Le présent document constitue l’une des trois parties de l’ISO 7784 traitant des méthodes d’essai
utilisées pour la détermination de la résistance à l’abrasion des revêtements au moyen de roues
abrasives. Les caractéristiques de ces méthodes et leurs différences sont résumées dans le Tableau 1.
Tableau 1 — Types de méthode
Roue abrasive
Mouvement de l’éprou-
Norme
vette
Type Degré de liberté
Papier abrasif sur roue en
ISO 7784-1
caoutchouc
Rotation libre Rotation
Roue abrasive en caout-
ISO 7784-2
chouc
Papier abrasif sur roue Rigide – avec une rotation Mouvement de va-et-vient
ISO 7784-3
a
métallique dépendant de la course linéaire
a
Un mécanisme fait tourner la roue abrasive d’un petit angle après chaque va-et-vient de manière à faire apparaître une
surface non utilisée de papier abrasif.
Il est préférable d'appliquer les méthodes utilisant des roues revêtues de papier abrasif (dans l'ISO 7784-1
et l'ISO 7784-3).
v
© ISO 2022 – Tous droits réservés

---------------------- Page: 5 ----------------------
PROJET FINAL DE NORME INTERNATIONALE ISO/FDIS 7784-2:2022(F)
Peintures et vernis — Détermination de la résistance à
l'abrasion —
Partie 2:
Méthode utilisant des roues abrasives en caoutchouc et
une éprouvette rotative
1 Domaine d'application
Le présent document spécifie une méthode permettant de déterminer la résistance à l’abrasion des
revêtements en appliquant deux roues abrasives en caoutchouc qui sont chargées et qui tournent
librement, mais de manière excentrée sur le revêtement de l’éprouvette rotative.
2 Références normatives
L
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.