SIST EN 16094:2012
(Main)Laminate floor coverings - Test method for the determination of micro-scratch resistance
Laminate floor coverings - Test method for the determination of micro-scratch resistance
This European Standard specifies a test method for the micro-scratch resistance which can be used for all types of laminate floor coverings.
Laminatböden - Prüfverfahren zur Bestimmung der Mikrokratzbeständigkeit
Diese Europäische Norm legt ein Prüfverfahren zur Bestimmung der Mikrokratzbeständigkeit fest, das für alle Arten von Laminatböden angewendet werden kann.
Revêtements de sol stratifiés - Méthode d'essai pour la détermination de la résistance aux micro-rayures
La présente Norme européenne spécifie une méthode d’essai de résistance aux micro-rayures pouvant être utilisée pour tous les types de revêtements de sol stratifiés.
Laminatne talne obloge - Preskusne metode za ugotavljanje odpornosti proti mikropraskam
Ta evropski standard določa preskusno metodo za odpornost proti mikropraskam, ki se lahko uporablja za vse vrste laminatnih talnih oblog.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Laminatne talne obloge - Preskusne metode za ugotavljanje odpornosti proti mikropraskamLaminatböden - Prüfverfahren zur Bestimmung der MikrokratzbeständigkeitRevêtements de sol stratifiés - Méthode d'essai pour la détermination de la résistance aux micro-rayuresLaminate floor coverings - Test method for the determination of micro-scratch resistance97.150Netekstilne talne oblogeNon-textile floor coveringsICS:Ta slovenski standard je istoveten z:EN 16094:2012SIST EN 16094:2012en,fr,de01-marec-2012SIST EN 16094:2012SLOVENSKI
STANDARD
SIST EN 16094:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16094
January 2012 ICS 97.150 English Version
Laminate floor coverings - Test method for the determination of micro-scratch resistance
Revêtements de sol stratifiés - Méthode d'essai pour la détermination de la résistance aux micro-rayures
Laminatböden - Prüfverfahren zur Bestimmung der Mikrokratzbeständigkeit This European Standard was approved by CEN on 26 November 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16094:2012: ESIST EN 16094:2012
EN 16094:2012 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .44 Principle .45 Apparatus and materials .56 Assembly and maintenance of the Martindale tester .77 Preparation and conditioning .77.1 Preparation .77.2 Test surface .78 Test procedure .78.1 General .78.2 Testing .88.2.1 Procedure A .88.2.2 Procedure B .99 Test report .9Annex A (normative)
Method for checking the Lissajous figure . 10Annex B (normative)
Classification of the image after scratching according to procedure B . 11Bibliography . 12 SIST EN 16094:2012
EN 16094:2012 (E) 3 Foreword This document (EN 16094:2012) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. SIST EN 16094:2012
EN 16094:2012 (E) 4 1 Scope This European Standard specifies a test method for the micro-scratch resistance which can be used for all types of laminate floor coverings.
2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 2813, Paints and varnishes — Determination of specular gloss of non-metallic paint films at 20°, 60° and 85° (ISO 2813) EN ISO 12945-2, Textiles — Determination of fabric propensity to surface fuzzing and to pilling — Part 2: Modified Martindale method (ISO 12945-2) EN ISO 12947-1, Textiles - Determination of the abrasion resistance of fabrics by the Martindale method — Part 1: Martindale abrasion testing apparatus (ISO 12947-1) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 cycle completion of all the translational movements tracing a Lissajous figure comprising 16 rubs NOTE This comprises of 16 revolutions of the two outer drives and 15 revolutions of the inner drive of the Martindale tester. 3.2 Lissajous figure figure created by movement which changes from a circle gradually narrowing ellipses, until it becomes a straight line, from which progressively widening ellipses develop, in a diagonally opposite direction before the pattern is repeated
3.3 rub one revolution of the two outer drives of the Martindale tester
4 Principle The sample is fixed on a horizontal table. A circular scrub material fixed on a holder impacts on the sample with a defined load. Table and holder are moved perpendicular to each other in a translational movement, with defined frequencies, tracing a Lissajous figure. The holder is additionally freely rotatable around its own axis perpendicular to the horizontal plane.
The sample is exposed to the scrub material for a predetermined number of rubs. The changes of the surface are determined by gloss measurement and visual assessment.
SIST EN 16094:2012
EN 16094:2012 (E) 5 5 Apparatus and materials 5.1 Martindale tester: The Martindale tester shall be as described in EN ISO 12947-1 with the following exceptions: the “abrading table” is the table for the sample; the “clamping ring and mechanism” is not necessary; the “specimen holder” is the holder for the scrub material; the “loading pieces” are not necessary. 5.2 Holder for scrub material: The holder for scrub material shall be as described in EN ISO 12945-2, with the following exceptions: version 1: the rubber retaining ring is not required. This assembly consists of spindle, scrub holder and small ring weight. The total mass of this assembly is (413 ± 2) g (nominally called 4N); version 2: the assembly according to version 1, however the small ring weight is replaced by the large weight. The total mass of this assembly is (612 ± 2) g (nominally called 6N). 5.3 Diffuse lig
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.