SIST EN 60730-2-5:2015
(Main)Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems (IEC 60730-2-5:2013 , modified)
Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems (IEC 60730-2-5:2013 , modified)
This part of IEC 60730 applies to automatic electrical burner control systems for the automatic
control of burners for oil, gas, coal or other combustibles for household and similar use
including heating, air conditioning and similar use.
This part 2-5 is applicable to a complete burner control system and to a separate
programming unit. This part 2-5 is also applicable to a separate electronic high-voltage
ignition source and to a separate flame detector.
NOTE Separate ignition devices (electrodes, pilot burners, etc.) are not covered by this part 2-5 unless they are
submitted as part of a burner control system. Requirements for separate ignition transformers are contained in
IEC 60989.
Throughout this part 2-5, where it can be used unambiguously, the word "system" means
"burner control system" and "systems" means "burner control systems".
Systems utilizing thermoelectric flame supervision are not covered by this part 2-5.
Automatische elektrische Regel- und Steuergeräte für den Hausgebrauch und ähnliche Anwendungen - Teil 2-5: Besondere Anforderungen an automatische elektrische Brenner-Steuerungs- und Überwachungssysteme (IEC 60730-2-5:2013 , modifiziert)
Dispositifs de commande électrique automatiques - Partie 2-5: Exigences particulières pour les systèmes de commande électrique automatiques des brûleurs (IEC 60730-2-5:2013 , modifiée)
La IEC 60730-2-5:2013 s'applique aux systèmes de commande électrique automatiques de brûleurs pour la commande automatique de brûleurs pour fioul, gaz, charbon ou autres combustibles à usage domestique et analogue, y compris le chauffage, la climatisation et usages analogues. La présente partie 2-5 est applicable à un système complet de commande de brûleur et à une unité de programmation séparée. La présente partie 2-5 est également applicable à une source électronique d'allumage à haute tension séparée et à un détecteur de flamme séparé. Des dispositifs d'allumage séparés (électrodes, veilleuses de brûleur, etc.) ne sont pas couverts par la présente partie 2-5, à moins d'y être soumis en tant que partie d'un système de commande de brûleur. Les exigences pour les transformateurs séparés d'allumage sont traitées dans la CEI 60989. Les systèmes utilisant le contrôle thermoélectrique de flamme ne sont pas couverts par la présente partie 2-5. La présente partie 2-5 s'applique à la sécurité intrinsèque, aux valeurs de fonctionnement, aux temps de fonctionnement et aux séquences de fonctionnement déclarés par le fabricant, dans la mesure où ils interviennent dans la sécurité du brûleur, ainsi qu'aux essais des systèmes de commande électrique automatiques de brûleurs utilisés dans, sur, ou avec des brûleurs. La présente partie 2-5 est destinée à être utilisée avec la CEI 60730-1. Elle a été établie sur la base de la quatrième édition (2010) de cette publication. Les éditions futures de la CEI 60730-1, ou ses amendements, pourront être pris en considération. Le titre de la CEI 60730-2-5 Ed4.0 a été mis à jour en fonction du titre de la CEI 60730-1 Ed5.0. Cependant, la CEI 60730-2-5 Ed4.0 n'a pas été mise à jour conformément aux exigences techniques de la CEI 60730-1 Ed5.0. La présente partie 2-5 complète ou modifie les articles correspondants de la CEI 60730-1 de façon à la transformer en norme CEI: Exigences de sécurité pour les systèmes de commande électrique automatiques des brûleurs. Mots-clés: commande automatique, commande de brûleur
Avtomatske električne krmilne naprave - 2-5. del: Posebne zahteve za avtomatske električne krmilne sisteme gorilnikov (IEC 60730-2-5:2013 , spremenjen)
Ta del standarda IEC 60730 se uporablja za avtomatske električne krmilne sisteme gorilnikov za avtomatsko krmiljenje gorilnikov na olje, plin, premog ali druge vnetljive snovi za gospodinjstvo in podobno uporabo, vključno z ogrevanjem, ohlajanjem s klimatsko napravo in podobno uporabo.
Ta del 2-5 se uporablja za celovit sistem krmiljenja gorilnika in za ločeno enoto za programiranje. Ta del 2-5 se uporablja tudi za ločeni elektronski visokonapetostni vir vžiga in za ločeno napravo za zaznavanje plamena.
OPOMBA: Ločene vžigalne naprave (elektrode, pilotni gorilniki itd.) niso zajete v tem delu 2-5, razen če so predložene kot del sistema krmiljenja gorilnika. Zahteve za ločene transformatorje vžiga so zajete v standardu IEC 60989.
V tem celotnem delu 2-5 beseda »sistem«, kjer jo je mogoče uporabiti nedvoumno, pomeni »krmilni sistem gorilnika« in beseda »sistemi« pomeni »krmilni sistemi gorilnikov«.
Sistemi, ki uporabljajo termoelektrični nadzor plamena, niso zajeti v tem delu 2-5.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60730-2-5:2015
01-julij-2015
1DGRPHãþD
SIST EN 60730-2-5:2002
SIST EN 60730-2-5:2002/A1:2005
SIST EN 60730-2-5:2002/A11:2005
SIST EN 60730-2-5:2002/A2:2010
$YWRPDWVNHHOHNWULþQHNUPLOQHQDSUDYHGHO 3RVHEQH]DKWHYH]DDYWRPDWVNH
HOHNWULþQHNUPLOQHVLVWHPHJRULOQLNRY ,(& VSUHPHQMHQ
Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical
burner control systems (IEC 60730-2-5:2013 , modified)
Automatische elektrische Regel- und Steuergeräte für den Hausgebrauch und ähnliche
Anwendungen - Teil 2-5: Besondere Anforderungen an automatische elektrische Brenner
-Steuerungs- und Überwachungssysteme (IEC 60730-2-5:2013 , modifiziert)
Dispositifs de commande électrique automatiques - Partie 2-5: Exigences particulières
pour les systèmes de commande électrique automatiques des brûleurs (IEC 60730-2-
5:2013 , modifiée)
Ta slovenski standard je istoveten z: EN 60730-2-5:2015
ICS:
97.120 Avtomatske krmilne naprave Automatic controls for
za dom household use
SIST EN 60730-2-5:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 60730-2-5:2015
---------------------- Page: 2 ----------------------
SIST EN 60730-2-5:2015
EUROPEAN STANDARD
EN 60730-2-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2015
ICS 97.120 Supersedes EN 60730-2-5:2002
English Version
Automatic electrical controls -
Part 2-5: Particular requirements for automatic electrical burner
control systems
(IEC 60730-2-5:2013 , modified)
Dispositifs de commande électrique automatiques - Automatische elektrische Regel- und Steuergeräte für den
Partie 2-5: Exigences particulières pour les systèmes de Hausgebrauch und ähnliche Anwendungen -
commande électrique automatiques des brûleurs Teil 2-5: Besondere Anforderungen an automatische
(IEC 60730-2-5:2013 , modifiée) elektrische Brenner-Steuerungs- und
Überwachungssysteme
(IEC 60730-2-5:2013 , modifiziert)
This European Standard was approved by CENELEC on 2014-11-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any
alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60730-2-5:2015 E
---------------------- Page: 3 ----------------------
SIST EN 60730-2-5:2015
EN 60730-2-5:2015 – 2 –
Foreword
This document (EN 60730-2-5:2015) consists of the text of IEC 60730-2-5:2013 prepared by
IEC/TC 72 "Automatic electrical controls", together with the common modifications prepared by
CLC/TC 72 "Automatic controls for household use".
The following dates are fixed:
• latest date by which the document has
(dop) 2015-08-27
to be implemented at national level
by publication of an identical
national standard or by endorsement
• latest date by which the national standards
(dow) 2017-11-17
conflicting with the document have to be withdrawn
This document supersedes EN 60730-2-5:2002.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed
for Use within Certain Voltage Limits (LVD - 2006/95/EC).
Endorsement notice
The text of the International Standard IEC 60730-2-5:2013 was approved by CENELEC as a European
Standard with agreed common modifications.
COMMON MODIFICATIONS
Foreword Delete
2 Definitions
2.3.127 Delete Note 1 to entry.
6 Classification
6.11 Replace the text of the addition by the following:
The minimum value is 250 000 automatic cycles.
---------------------- Page: 4 ----------------------
SIST EN 60730-2-5:2015
– 3 – EN 60730-2-5:2015
15 Manufacturing deviation and drift
15.7 Delete the note.
17 Endurance
17.16.102.1 a) Delete the note.
Annexes
Annex H
H.26.10 Delete up to and included H.26.10.5.101.6 and replace by “Void”:
H.26.11.103 Delete Note 2.
Table H.21 In Note 7, delete the last sentence of the modification “In Canada and in the USA, the
nominal cycle is 100 000.”.
H.27.1.2.3 Delete the text: “The modification applies to the French text only.”
---------------------- Page: 5 ----------------------
SIST EN 60730-2-5:2015
EN 60730-2-5:2015 – 4 –
Add Annexes ZA, ZB, ZC and ZZ as follows.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
This annex of EN 60730-1:2011 is applicable except as follows:
Addition:
Publication Year Title EN/HD Year
IEC 60068-2-6 - Environmental testing EN 60068-2-6 -
Part 2-6: Tests - Test Fc: Vibration
(sinusoidal)
IEC 61643-11 - Low-voltage surge protective devices EN 61643-11 -
Part 11: Surge protective devices connected
to low-voltage power systems -
Requirements and test methods
---------------------- Page: 6 ----------------------
SIST EN 60730-2-5:2015
– 5 – EN 60730-2-5:2015
Annex ZB
(normative)
Special national conditions
This annex of EN 60730-1:2011 is applicable.
There are no special conditions (snc) causing a deviation from this European Standard other than those
listed in Annex ZB to EN 60730-1:2011.
---------------------- Page: 7 ----------------------
SIST EN 60730-2-5:2015
EN 60730-2-5:2015 – 6 –
Annex ZC
(informative)
A-deviations
This annex of EN 60730-1:2011 is applicable except as follows:
Addition:
Clause Deviation
Annex H Austria: Bundesgesetzblatt 19. Verordnung: Luftreinhalteverordnung 1989 (LVR-K 1989,
air clean keeping decree for vessel equipment), last valid modification Nov. 4, 1997 by
324. Verordnung: Änderung der Luftreinhalteverordnung für Kesselanlagen 1989
(modification of LVR-K 1989, air clean keeping decree for vessel equipment):
§ 8(1) Werden Dampfkesselanlagen mit Brennern ausgerüstet, die in den
Anwendungsbereich nachstehender ÖNORMen fallen, so sind diese ÖNORMen
verbindlich anzuwenden:
(Whenever steam boilers are equipped with burners concerned by the following
standards, these standards have to be applied:)
- ÖNORM EN 267/1991: Atomizing oil burners of monobloc type-Testing;
- ÖNORM M 7540-1/1994: Atomizing oil burners of monobloc type for the heating fuels
"fuel oil light", "fuel oil medium" and "fuel oil heavy" - Terminology, requirements,
testing, marking of conformty;
- ÖNORM M 7445/1984: Forced-air gasburners;
- ÖNORM M 7445/1990: Fan-assisted gas burners with low NOx-emission; nitrogen
oxide measurement."
---------------------- Page: 8 ----------------------
SIST EN 60730-2-5:2015
– 7 – EN 60730-2-5:2015
Annex ZZ
(informative)
Coverage of Essential Requirements of EU Directives
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers all
relevant essential requirements as given in Article 1 of Annex I of the EC Directive EMC (2004/108/EC).
Compliance with this standard provides one means of conformity with the specified essential requirements
of the Directive concerned.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within
the scope of this standard.
____________
---------------------- Page: 9 ----------------------
SIST EN 60730-2-5:2015
---------------------- Page: 10 ----------------------
SIST EN 60730-2-5:2015
IEC 60730-2-5
®
Edition 4.0 2013-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Automatic electrical controls –
Part 2-5: Particular requirements for automatic electrical burner control systems
Dispositifs de commande électrique automatiques –
Partie 2-5: Exigences particulières pour les systèmes de commande électrique
automatiques des brûleurs
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX XA
ICS 97.120 ISBN 978-2-8322-1171-7
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 11 ----------------------
SIST EN 60730-2-5:2015
– 2 – 60730-2-5 © IEC:2013
CONTENTS
FOREWORD . 4
1 Scope and normative references . 6
2 Definitions . 7
3 General requirements . 14
4 General notes on tests . 14
5 Rating . 15
6 Classification . 15
7 Information . 17
8 Protection against electric shock . 20
9 Provision for protective earthing . 20
10 Terminals and terminations . 20
11 Constructional requirements . 21
12 Moisture and dust resistance . 27
13 Electric strength and insulation resistance . 27
14 Heating . 28
15 Manufacturing deviation and drift . 29
16 Environmental stress . 30
17 Endurance . 31
18 Mechanical strength . 34
19 Threaded parts and connections . 34
20 Creepage distances, clearances and distances through solid insulation . 34
21 Resistance to heat, fire and tracking . 34
22 Resistance to corrosion . 34
23 Electromagnetic compatibility (EMC) requirements – emission. 34
24 Components . 34
25 Normal operation . 34
26 Electromagnetic compatibility (EMC) requirements – immunity . 34
27 Abnormal operation . 35
28 Guidance on the use of electronic disconnection . 35
Annex H (normative) Requirements for electronic controls . 36
Annex J (normative) Requirements for controls using thermistors . 49
Annex BB (informative) Functional characteristics of burner control systems to be
specified by the relevant appliance standards, as applicable . 50
Bibliography . 51
Figure 101 – Pulse spark generation . 20
Figure H.2 (H.26.5.4.2 of the previous version) – Voltage variation test . 39
Table 1 (7.2 of the previous edition) (1 of 2) . 18
Table H.1 (7.2 of the previous edition) . 36
Table H.101 – Voltage dips, short interruptions and voltage variations . 37
---------------------- Page: 12 ----------------------
SIST EN 60730-2-5:2015
60730-2-5 © IEC:2013 – 3 –
Table H.13 (Table H.26.5.4.2 of the previous edition) – Timing of short-term supply
voltage variations . 38
Table H.102 – Test level for electrical fast transient burst . 41
Table H.103 – Peak voltages . 42
Table H.104 – Test levels for electrostatic discharge . 43
Table H.105 – Test levels for conducted disturbances on mains and I/O lines . 44
Table H.18 (Table H.26.12.3.1 of the previous edition) – Immunity to radiated
electromagnetic fields . 45
Table BB.1 – Functional characteristics of burner control systems to be specified by the
relevant appliance standards, as applicable . 50
---------------------- Page: 13 ----------------------
SIST EN 60730-2-5:2015
– 4 – 60730-2-5 © IEC:2013
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
AUTOMATIC ELECTRICAL CONTROLS –
Part 2-5: Particular requirements for automatic
electrical burner control systems
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60730-2-5 has been prepared by IEC technical committee 72:
Automatic electrical controls.
The text of this standard is based on the following documents:
FDIS Report on voting
72/922/FDIS 72/929/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 14 ----------------------
SIST EN 60730-2-5:2015
60730-2-5 © IEC:2013 – 5 –
This part 2-5 is intended to be used in conjunction with IEC 60730-1. It was established on the
basis of the fourth edition (2010) of that publication. Consideration may be given to future
editions of, or amendments to, IEC 60730-1.
The title of IEC 60730-2-5 Ed. 4 has been updated to the title of IEC 60730-1 Ed. 5.0. However,
IEC 60730-2-5 Ed. 4.0 has not been updated in accordance with the technical requirements in
IEC 60730-1 Ed. 5.0.
This part 2-5 supplements or modifies the corresponding clauses in IEC 60730-1 so as to
convert that publication into the IEC standard: Safety requirements for automatic electrical
burner control systems.
Where this part 2-5 states "addition", "modification", or "replacement", the relevant
requirement, test specification or explanatory matter in Part 1 should be adapted accordingly.
Where no change is necessary, this part 2-5 indicates that the relevant clause or subclause
applies.
In the development of a fully international standard, it has been necessary to take into
consideration the differing requirements resulting from practical experience in various parts of
the world and to recognize the variation in national electrical systems and wiring rules.
The “in some countries” notes regarding differing national practices are contained in the following subclauses:
– 2.3.127
– 6.11
– 15.7
– 17.16.102.1
– H.26.11.103
– Table H.21, Note 7
In this publication:
1) The following print types are used:
– Requirements proper: in roman type;
– Test specifications: in italic type;
– Explanatory matter; in small roman type;
– Words defined in Clause 2: bold.
2) Subclauses, notes, tables and figures which are additional to those in Part 1 are numbered
starting from 101, additional annexes are lettered AA, BB, etc.
A list of all parts of the IEC 60730 series, under the general title Automatic electrical controls
can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until the
stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to
the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 15 ----------------------
SIST EN 60730-2-5:2015
– 6 – 60730-2-5 © IEC:2013
AUTOMATIC ELECTRICAL CONTROLS –
Part 2-5: Particular requirements for automatic
electrical burner control systems
1 Scope and normative references
This clause of Part 1 is applicable except as follows:
1.1 Replacement:
This part of IEC 60730 applies to automatic electrical burner control systems for the automatic
control of burners for oil, gas, coal or other combustibles for household and similar use
including heating, air conditioning and similar use.
This part 2-5 is applicable to a complete burner control system and to a separate
programming unit. This part 2-5 is also applicable to a separate electronic high-voltage
ignition source and to a separate flame detector.
NOTE Separate ignition devices (electrodes, pilot burners, etc.) are not covered by this part 2-5 unless they are
submitted as part of a burner control system. Requirements for separate ignition transformers are contained in
IEC 60989.
Throughout this part 2-5, where it can be used unambiguously, the word "system" means
"burner control system" and "systems" means "burner control systems".
Systems utilizing thermoelectric flame supervision are not covered by this part 2-5.
1.1.1 This part 2-5 applies to the inherent safety, to the manufacturer's declared operating
values, operating times and operating sequences where such are associated with burner
safety and to the testing of automatic electrical burner control systems used in, on, or in
association with, burners.
NOTE Requirements for specific operating values, operating times and operating sequences are given in the
standards for appliances and equipment.
Systems for equipment not intended for normal household use, but which nevertheless may be
used by the public, such as equipment intended to be used by laymen in shops, in light industry
and on farms, are within the scope of this part 2-5.
This part 2-5 applies to systems using NTC or PTC thermistors, additional requirements for
which are contained in Annex J.
This part 2-5 does not apply to systems designed exclusively for industrial applications.
1.1.2 This part 2-5 applies to manual controls when such are electrically and/or mechanically
integral with automatic controls.
NOTE Requirements for manual switches not forming part of an automatic control are contained in IEC 61058-1.
Throughout this part 2-5, the word "equipment" means "appliance and equipment".
---------------------- Page: 16 ----------------------
SIST EN 60730-2-5:2015
60730-2-5 © IEC:2013 – 7 –
1.2 Replacement:
This part 2-5 applies to systems with a rated voltage not exceeding 660 V and with a rated
current not exceeding 63 A.
1.3 Replacement:
This part 2-5 does not take into account the response value of an automatic action of a
control, if such a response value is dependent upon the method of mounting the control in the
equipment. Where a response value is of significant purpose for the protection of the user, or
surroundings, the value defined in the appropriate household equipment standard or as
determined by the manufacturer applies.
NOTE This part 2-5 includes systems responsive to flame properties.
1.4 Replacement:
This part 2-5 applies also to systems incorporating electronic devices, requirements for which
are contained in Annex H.
1.5 Normative references
This clause of Part 1 is applicable except as follows:
Addition:
IEC 60068-2-6, Environmental testing – Part 2: Tests – Test Fc: Vibration (sinusoidal)
IEC 61643-11, Low-voltage surge protective devices – Part 11: Surge protective devices
connected to low-voltage power systems – Requirements and test methods
2 Definitions
This clause of Part 1 is applicable except as follows:
2.2 Definitions of types of control according to purpose
Additional definitions:
2.2.101
burner control system
system which includes a programming unit, a flame detector and may include an ignition
source and/or ignition device and which monitors the operation of fuel burners
Note 1 to entry: The various functions of the system may be in one or more housings.
---------------------- Page: 17 ----------------------
SIST EN 60730-2-5:2015
– 8 – 60730-2-5 © IEC:2013
2.2.102
flame detector
device which provides the programming unit with a signal indicating the presence or absence
of flame
Note 1 to entry: It includes the flame sensor and may include an amplifier and a relay for signal transmission. The
amplifier and relay may be in its own housing or combined with the programming unit.
2.2.103
flame sensor
device which senses the flame and provides the input signal to the flame detector amplifier
Note 1 to entry: Examples are optical sensors and flame electrodes (flame rods).
2.2.104
ignition source
electrical or electronic system component which provides energy to an ignition device
Note 1 to entry: It may be separated from or incorporated in the programming unit. Examples are ignition
transformers and electronic high-voltage generators.
2.2.105
ignition device
device mounted on or adjacent to a burner for igniting fuel at the burner
Note 1 to entry: Examples are pilot burners, spark electrodes and hot surface igniters.
2.2.106
programming unit
device which controls the burner operation in a declared sequence from start-up to shut-down
within declared timings and in response to signals from regulating, limiting and monitoring
devices
2.2.107
multitry system
system that allows more than one valve open period during its declared operating sequence
2.3 Definitions relating to the function of controls
2.3.30
T
max
Replace "switch head" by "burner control system."
Additional definitions:
2.3.101
automatic recycle
automatic repetition of the start-up procedure, without manual intervention, following loss of the
supervised flame and subsequent fuel supply shutoff
2.3.102
controlled shut-down
de-energization of the fuel flow means as a result of the opening of a control loop by a control
device such as a thermostat leading the system to return to the start position
Note 1 to entry: Controlled shut-down may include additional actions by the system.
---------------------- Page: 18 ----------------------
SIST EN 60730-2-5:2015
60730-2-5 © IEC:2013 – 9 –
2.3.103
flame detector response time
period of time between the loss of the sensed flame and the signal indicating the absence of
flame
2.3.104
flame detector operating characteristics
that function of the flame detector which indicates absence or presence of flame as
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.