Open die steel forgings for general engineering purposes - Part 3: Alloy special steels

This part of this European Standard specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from alloy special steel and supplied in the quenched and tempered condition. Note: The majority of steels listed in this Part of EN 10250 are identical to steels specified in EN 10083-1 and more extensive information on hardenability and technological properties is given in that European Standard.

Freiformschmiedestücke aus Stahl für allgemeine Verwendung - Teil 3: Legierte Edelstähle

Dieser Teil dieser Europäischen Norm legt die allgemeinen technischen Lieferbedingungen für Freiformschmiedestücke und geschmiedete Stäbe sowie vorgeschmiedete und in Ringwalzwerken fertig umgeformte Erzeugnisse fest, die aus legiertem Edelstahl gefertigt und im vergüteten Zustand geliefert werden.
Die meisten Stähle, die in diesem Dokument aufgeführt sind, sind mit jenen identisch, die in EN ISO 683- 1 und EN ISO 683- 2 festgelegt sind. Umfassendere Angaben über die Härtbarkeit und technologische Eigenschaften werden in diesen Normen getroffen.
Angaben über die allgemeinen technischen Lieferbedingungen enthält EN 10021.

Pièces forgées en acier pour usage général - Partie 3: Aciers spéciaux alliés

Le présent document spécifie les exigences techniques générales de livraison des pièces obtenues par forgeage libre, des barres forgées et des produits pré-forgés et finis par laminage circulaire, fabriqués en aciers spéciaux alliés et livrées à l'état trempé et revenu.
La majorité des aciers cités dans le présent document sont identiques aux aciers spécifiés dans l’EN ISO 683-1 et l’EN ISO 683-2, et des informations plus complètes sur la trempabilité et les propriétés technologiques sont données dans ces normes.
Les informations générales sur les conditions techniques de livraison sont données dans l’EN 10021.

Prosto kovani jekleni izkovki za splošno tehnično uporabo - 3. del: Legirana plemenita jekla

Ta del tega evropskega standarda določa tehnične dobavne zahteve za prosto kovane izkovke, kovane drogove in izdelke, predhodno kovane in dokončane v mlinih z obročastimi valji, ki so izdelani iz legiranega plemenitega jekla ter dobavljeni v kaljenem in tempranem stanju. Opomba: Večina jekel, navedenih v tem delu standarda EN 10250, je enaka jeklom iz standarda EN 10083-1, v tem evropskem standardu pa so podane obsežnejše informacije o kaljivosti in tehnoloških lastnostih.

General Information

Status
Published
Public Enquiry End Date
27-Jan-2021
Publication Date
11-Apr-2022
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
06-Apr-2022
Due Date
11-Jun-2022
Completion Date
12-Apr-2022

Relations

Buy Standard

Standard
EN 10250-3:2022
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 10250-3:2021
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 10250-3:2022
01-maj-2022
Nadomešča:
SIST EN 10250-3:2000
Prosto kovani jekleni izkovki za splošno tehnično uporabo - 3. del: Legirana
plemenita jekla
Open die steel forgings for general engineering purposes - Part 3: Alloy special steels
Freiformschmiedestücke aus Stahl für allgemeine Verwendung - Teil 3: Legierte
Edelstähle
Pièces forgées en acier pour usage général - Partie 3: Aciers spéciaux alliés
Ta slovenski standard je istoveten z: EN 10250-3:2022
ICS:
77.140.20 Visokokakovostna jekla Stainless steels
77.140.85 Železni in jekleni kovani Iron and steel forgings
izdelki
SIST EN 10250-3:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 10250-3:2022

---------------------- Page: 2 ----------------------
SIST EN 10250-3:2022


EN 10250-3
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2022
EUROPÄISCHE NORM
ICS 77.140.20; 77.140.85 Supersedes EN 10250-3:1999
English Version

Open die steel forgings for general engineering purposes -
Part 3: Alloy special steels
Pièces forgées en acier pour usage général - Partie 3: Freiformschmiedestücke aus Stahl für allgemeine
Aciers spéciaux alliés Verwendung - Teil 3: Legierte Edelstähle
This European Standard was approved by CEN on 14 February 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10250-3:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 10250-3:2022
EN 10250-3:2022 (E)
Contents Page

European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Chemical composition . 4
4.1 Cast analysis . 4
4.2 Product analysis . 4
5 Heat treatment . 4
6 Mechanical properties . 4
Annex A (informative) Heat treatment. 9
Bibliography . 10
2

---------------------- Page: 4 ----------------------
SIST EN 10250-3:2022
EN 10250-3:2022 (E)
European foreword
This document (EN 10250-3:2022) has been prepared by Technical Committee CEN/TC 459 “ECISS -
1
European Committee for Iron and Steel Standardization” , the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards shall
be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10250-3:1999.
In comparison with the previous edition, the following technical modifications have been made:
— updating of normative references.
EN 10250, Open die steel forgings for general engineering purposes, consists of the following parts:
— Part 1: General requirements;
— Part 2: Non-alloy quality and special steels;
— Part 3: Alloy special steels;
— Part 4: Stainless steels.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.

1
Through its sub-committee SC 11 “Steel castings and forgings” (secretariat: AFNOR).
3

---------------------- Page: 5 ----------------------
SIST EN 10250-3:2022
EN 10250-3:2022 (E)
1 Scope
This document specifies the technical delivery requirements for open die forgings, forged bars and
products pre-forged and finished in ring rolling mills, manufactured from alloy special steel and supplied
in the quenched and tempered condition.
The majority of steels listed in this document are identical to steels specified in EN ISO 683-1 and
EN ISO 683-2 and more extensive information on hardenability and technological properties is given in
these standards.
General information on technical delivery conditions is given in EN 10021.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10250-1:2022, Open die steel forgings for general engineering purposes - Part 1: General requirements
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/
— ISO Online browsing platform: available at https://www.iso.org/obp
4 Chemical composition
4.1 Cast analysis
The chemical composition of the steel shall be determined by cast analysis and shall conform to the
analysis given in Table 1 (see EN 10250-1:2022, A.7 and A.8).
Measures should be taken to prevent the addition from the scrap, or other material used in the
manufacture of the steels, of such elements which affect the hardenability, mechanical properties and
applicability of the steel.
...

SLOVENSKI STANDARD
oSIST prEN 10250-3:2021
01-januar-2021
Prosto kovani jekleni izkovki za splošno tehnično uporabo - 3. del: Legirana
plemenita jekla
Open die steel forgings for general engineering purposes - Part 3: Alloy special steels
Freiformschmiedestücke aus Stahl für allgemeine Verwendung - Teil 3: Legierte
Edelstähle
Pièces forgées en acier pour usage général - Partie 3: Aciers spéciaux alliés
Ta slovenski standard je istoveten z: prEN 10250-3
ICS:
77.140.20 Visokokakovostna jekla Stainless steels
77.140.85 Železni in jekleni kovani Iron and steel forgings
izdelki
oSIST prEN 10250-3:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 10250-3:2021

---------------------- Page: 2 ----------------------
oSIST prEN 10250-3:2021


DRAFT
EUROPEAN STANDARD
prEN 10250-3
NORME EUROPÉENNE

EUROPÄISCHE NORM

November 2020
ICS 77.140.20; 77.140.85 Will supersede EN 10250-3:1999
English Version

Open die steel forgings for general engineering purposes -
Part 3: Alloy special steels
Pièces forgées en acier pour usage général - Partie 3: Freiformschmiedestücke aus Stahl für allgemeine
Aciers spéciaux alliés Verwendung - Teil 3: Legierte Edelstähle
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 11.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10250-3:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 10250-3:2021
prEN 10250-3:2020 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Chemical composition . 4
4.1 Cast analysis . 4
4.2 Product analysis . 4
5 Heat treatment . 4
6 Mechanical properties . 4
Annex A (informative) Heat treatment [3] . 9
Bibliography . 10

2

---------------------- Page: 4 ----------------------
oSIST prEN 10250-3:2021
prEN 10250-3:2020 (E)
European foreword
This document (prEN 10250-3:2020) has been prepared by Technical Committee CEN/TC 459 “Steel
castings and forgings”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10250-3:1999.
In comparison with the previous edition, the following technical modifications have been made:
— updating of normative references.
EN 10250, Open die steel forgings for general engineering purposes, consists of the following parts:
— Part 1: General requirements;
— Part 2: Non-alloy quality and special steels;
— Part 3: Alloy special steels;
— Part 4: Stainless steels.
3

---------------------- Page: 5 ----------------------
oSIST prEN 10250-3:2021
prEN 10250-3:2020 (E)
1 Scope
This document specifies the technical delivery requirements for open die forgings, forged bars and
products pre-forged and finished in ring rolling mills, manufactured from alloy special steel and supplied
in the quenched and tempered condition.
The majority of steels listed in this document are identical to steels specified in EN ISO 683-1 and
EN ISO 683-2 and more extensive information on hardenability and technological properties is given in
these standards.
General information on technical delivery conditions is given in EN 10021.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
prEN 10250-1:2020, Open die steel forgings for general engineering purposes - Part 1: General
requirements
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
4 Chemical composition
4.1 Cast analysis
The chemical composition of the steel shall be determined by cast analysis and shall conform to the
analysis given in Table 1 (see A.7 and A.8 of prEN 10250-1:2020).
Measures should be taken to prevent the addition from the scrap, or other material used in the
manufacture of the steels, of such elements which affect the hardenability, mechanical properties and
applicability of the steel.
4.2 Product analysis
The product analysis shall not deviate from the specified cast analysis (see Table 1) by more than the
values specified i
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.