SIST EN ISO 6411:2001
(Main)Technical drawings - Simplified representation of centre holes (ISO 6411:1982)
Technical drawings - Simplified representation of centre holes (ISO 6411:1982)
This representation mode may be used particulary when it is not necessary to show the exact form and size and where the designation of standardized centre holes is sufficient for information. Annex A gives the dimensions for types R, A and B, and Annex B the proportions and dimensions of symbols.
Technische Zeichnungen - Vereinfachte Darstellung von Zentrierbohrungen (ISO 6411:1982)
Diese Norm legt die vereinfachte Darstellung von Zentrierbohrungen und deren Bezeichnung fest. Die vereinfachte Darstellung von Zentrierbohrungen kann besonders dann angewendet werden, wenn es nicht notwendig ist, die genaue Form und Größe darzustellen und die Bezeichnung von genormten Zentrierbohrungen als Information genügt.
Dessins techniques - Représentation simplifiée des trous de centre (ISO 6411:1982)
La présente Norme internationale spécifie une représentation simplifiée des trous de centre et leur désignation. La représentation simplifiée des trous de centre peut être utilisée en particulier lorsqu'il n'est pas nécessaire de montrer la forme et les dimensions exactes des trous de centre et que leur désignation normalisée suffit pour l'information.
Tehniške risbe - Poenostavljeno prikazovanje centrirnih izvrtin (ISO 6411:1982)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6411:2001
01-julij-2001
Tehniške risbe - Poenostavljeno prikazovanje centrirnih izvrtin (ISO 6411:1982)
Technical drawings - Simplified representation of centre holes (ISO 6411:1982)
Technische Zeichnungen - Vereinfachte Darstellung von Zentrierbohrungen (ISO
6411:1982)
Dessins techniques - Représentation simplifiée des trous de centre (ISO 6411:1982)
Ta slovenski standard je istoveten z: EN ISO 6411:1997
ICS:
01.100.20 Konstrukcijske risbe Mechanical engineering
drawings
SIST EN ISO 6411:2001 sl
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6411:2001
---------------------- Page: 2 ----------------------
SIST EN ISO 6411:2001
---------------------- Page: 3 ----------------------
SIST EN ISO 6411:2001
---------------------- Page: 4 ----------------------
SIST EN ISO 6411:2001
International Standard
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION.MEX~YHAPO,4HAR OPTAHM3ALWlfl l-l0 CTAH~APTM3ALWl*ORGANISATlON INTERNATIONALE DE NORMALISATION
Simplified representation of
Technical drawings -
centre holes
Dessins techniques - Repr&entation simplifiee des trous de centre
First edition - 1982-04-15
Ref. No. ISO 6411-1982 (E)
UDC 744.4
Descriptors : engineering drawings, centre holes, graphic methods, generalities, designation.
Price based on 5 pages
---------------------- Page: 5 ----------------------
SIST EN ISO 6411:2001
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of
national Standards institutes (ISO memher bedies). The work of developing lnter-
national Standards is carried out through ISO technical committees. Every member
hody interested in a subject for which a technical committee has been set up has the
right to be represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the ISO Council.
International Standard ISO 6411 was developed hy Technical Committee ISO/TC 10,
Technical drawings, and was circulated to the member bedies in January 1980.
lt has been approved by the member bedies of the following countries :
France Poland
Australia
Austria Germany, F. R. Romania
India
Belgium South Africa, Rep. of
Italy Spain
Brazil
Canada Japan Sweden
China Korea, Dem. P. Rep. of Switzerland
Czechoslovakia Korea, Rep. of United Kingdom
Denmark Mexico USA
Finland Norway USSR
The memher body of the following country expressed disapproval of the document on
technical grounds
Netherlands
0 International Organkation for Standardkation, 1982
Printed in Switzerland
---------------------- Page: 6 ----------------------
SIST EN ISO 6411:2001
ISO 6411-1982 (EI
INTERNATIONAL STANDARD
Technical drawings -
Simplified representation of
centre holes
ISO 309811, Technical drawings - Lettering - Part 7 :
1 Scope and field of application
Curren tl y used charac ters.
This International Standard specifies the simplified represen-
ISO 6428, Technical drawings - Requirements for micro-
tation of centre holes and their designation. Simplified
cop ying. 1)
representation of centre holes may be used particularly when it
is not necessary to show the exact form and size and where the
designation of standardized centre holes is sufficient for infor-
mation.
3 Indication on drawings
2 References
3.1 Requirements
ISO 128, Technical drawings - General principles of presen-
Generally, three different requirements may be defined on
ta tion.
technical drawings for the form and size of centre holes,
ISO 866, Centre drills for centre holes without protecting namely :
chamfers - Type A.
a) centre hole is required on the finished Part;
ISO 2540, Centre drills for centre holes with protecting
b) centre hole tan be accepted on the finished Part, but is
chamfers - Type 6.
not a fundamental requirement;
ISO 2541, Centre drills for centre holes with radius form -
c) centre hole shall not exist on the finished part.
Type R.
-~
1) At present at the Stage of draft.
1
---------------------- Page: 7 ----------------------
SIST EN ISO 6411:2001
ISO 6411-1982 (E)
-
3.2 Simplified representation the outside countersink centre hole diam
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.