SIST EN 61249-2-23:2005

Materials for printed boards and other interconnecting structures -- Part 2-23: Reinforced base materials, clad and unclad - Non-halogenated phenolic cellulose paper reinforced laminated sheets, economic grade, copper-clad

This part of EN 61249 gives requirements for properties of non-halogenated phenolic cellulose paper copper-clad laminated sheets, economic grade, in thicknesses of 0,8 mm up to 3,2 mm. This standard covers materials with different requirements on flammability and are designated according to the following: Material 61249-2-23-1: general purpose grade, requirement on flammability not specified; Material 61249-2-23-2: materials of defined flammability (vertical burning test). These grades of material provide for one of two flammability requirements and designated as FV0 or FV1 in Table 8.

Materialien für Leiterplatten und andere Verbindungsstrukturen -- Teil 2-23: Kaschierte und unkaschierte verstärkte Basismaterialien - Kupferkaschierte halogenfreie Phenolharz-Hartpapiertafeln wirtschaftlicher Qualität

Matériaux pour circuits imprimés et autres structures d'interconnexion -- Partie 2-23: Matériaux de base renforcés, plaqués et non plaqués - Feuilles stratifiées renforcées de papier cellulose phénolique non halogéné, de qualité économique, plaquées cuivre

La présente partie de la EN 61249 indique les exigences concernant les propriétés des feuilles stratifiées renforcées en papier cellulose phénolique non halogéné, de qualité économique, plaquées cuivre d'épaisseur comprise entre 0,8 mm et 3,2 mm. Cette norme couvre les matériaux possédant différentes exigences sur l'inflammabilité et ils sont conçus selon ce qui suit: Matériau 61249-2-23-1: qualité d'usage courant, exigence sur l'inflammabilité non spécifié; Matériau 61249-2-23-2: matériaux d'inflammabilité définie (essai de combustion verticale). Cette qualité de matériaux est prévue pour une des deux exigences d'inflammabilité et désignées par FV0 ou FV1 dans le Tableau 8.

Materiali za tiskane plošče in druge povezovalne strukture – 2-23. del: Pokovinjeni in nepokovinjeni ojačeni osnovni materiali - Z bakrom pokovinjeni laminat, ojačen z nehalogeniziranim fenolnim celuloznim papirjem, ekonomični razred

General Information

• Status: Published
• Publication Date: 31-Aug-2005
• ICS: 31.180 - Printed circuits and boards
• Technical Committee: ITIV - Electronics assembly technology and Environmental standardization
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Sep-2005
• Due Date: 01-Sep-2005
• Completion Date: 01-Sep-2005
• Ref Project: EN 61249-2-23:2005 - Materials for printed boards and other interconnecting structures - Part 2-23: Reinforced base materials, clad and unclad - Non-halogenated phenolic cellulose paper reinforced laminated sheets, economic grade, copper-clad

Standards Content (Sample)

SLOVENSKI SIST EN 61249-2-23:2005

STANDARD
september 2005
Materiali za tiskane plošče in druge povezovalne strukture – 2-23. del:
Pokovinjeni in nepokovinjeni ojačeni osnovni materiali - Z bakrom pokovinjeni
laminat, ojačen z nehalogeniziranim fenolnim celuloznim papirjem,
ekonomični razred
Materials for printed boards and other interconnecting structures – Part 2-23:
Reinforced base materials, clad and unclad – Non-halogenated phenolic cellulose
paper reinforced laminated sheets, economic grade, copper-clad
ICS 31.180 Referenčna številka
SIST EN 61249-2-23:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 61249-2-23
NORME EUROPÉENNE
EUROPÄISCHE NORM March 2005

ICS 31.180


English version


Materials for printed boards and other interconnecting structures
Part 2-23: Reinforced base materials, clad and unclad –
Non-halogenated phenolic cellulose paper
reinforced laminated sheets, economic grade, copper-clad
(IEC 61249-2-23:2005)


Matériaux pour circuits imprimés  Materialien für Leiterplatten
et autres structures d'interconnexion und andere Verbindungsstrukturen
Partie 2-23: Matériaux de base renforcés, Teil 2-23: Kaschierte und unkaschierte
plaqués et non plaqués – verstärkte Basismaterialien –
Feuilles stratifiées renforcées de papier Kupferkaschierte halogenfreie
cellulose phénolique non halogéné, Phenolharz-Hartpapiertafeln
de qualité économique, plaquées cuivre wirtschaftlicher Qualität
(CEI 61249-2-23:2005) (IEC 61249-2-23:2005)


This European Standard was approved by CENELEC on 2005-02-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61249-2-23:2005 E

---------------------- Page: 2 ----------------------

EN 61249-2-23:2005 - 2 -
Foreword
The text of document 91/495/FDIS, future edition 1 of IEC 61249-2-23, prepared by IEC TC 91,
Electronics assembly technology, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 61249-2-23 on 2005-02-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2005-11-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-02-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61249-2-23:2005 was approved by CENELEC as a
European Standard without any modification.
_________

---------------------- Page: 3 ----------------------

- 3 - EN 61249-2-23:2005
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60194 1999 Printed board design, manufacture and - -
assembly - Terms and definitions

IEC 61189-2 1997 Test methods for electrical materials, EN 61189-2 1997
printed boards and other interconnection + corr. August 1997
structures and assemblies
Part 2: Test methods for materials for
interconnection structures

IEC 61249-5-1 1995 Materials for interconnection structures EN 61249-5-1 1996
Part 5: Sectional specification set for
conductive foils and films with or without
coatings - Section 1: Copper foils (for the
manufacture of copper-clad base
materials)

ISO 9000 2000 Quality management systems - EN ISO 9000 2000
Fundamentals and vocabulary

ISO 11014-1 1994 Safety data sheet for chemical products - -
Part 1: Content and order of sections

ISO 14001 1996 Environmental management systems EN ISO 14001 1996
Specification with guidance for use

---------------------- Page: 4 ----------------------

NORME CEI
INTERNATIONALE IEC
61249-2-23
INTERNATIONAL
Première édition
STANDARD
First edition
2005-01
Matériaux pour circuits imprimés
et autres structures d'interconnexion –
Partie 2-23:
Matériaux de base renforcés, plaqués et
non plaqués – Feuilles stratifiées renforcées
de papier cellulose phénolique non halogéné,
de qualité économique, plaquées cuivre
Materials for printed boards
and other interconnecting structures –
Part 2-23:
Reinforced base materials, clad and unclad –
Non-halogenated phenolic cellulose paper
reinforced laminated sheets, economic grade,
copper-clad
© IEC 2005 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale PRICE CODE Q
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 5 ----------------------

61249-2-23 © IEC:2005 – 3 –
CONTENTS
FOREWORD.7
1 Scope .13
2 Normative references .13
3 Materials and construction .15
3.1 Resin system.15
3.2 Reinforcement .15
3.3 Metal foil .15
4 Internal marking .15
5 Electrical properties.17
6 Non-electrical properties of the copper-clad laminate sheet .17
6.1 Appearance of the copper-clad sheet .17
6.2 Appearance of the unclad face.21
6.3 Laminate thickness, including copper foil .21
6.4 Bow and twist .21
6.5 Properties related to the copper foil bond .23
6.6 Punching and machining.25
6.7 Dimensional stability.25
6.8 Sheet sizes .25
6.9 Rectangularity of cut panels.25
7 Non-electrical properties of the base material after complete removal
of the copper foil .27
7.1 Appearance of the dielectric base material .27
7.2 Flexural strength .27
7.3 Flammability.27
7.4 Water absorption .27
7.5 Measling .29
7.6 Glass transition temperature and cure factor .29
8 Quality assurance.29
8.1 Quality system.29
8.2 Responsibility for inspection .29
8.3 Qualification inspection.29
8.4 Quality conformance inspection .29
8.5 Certificate of conformance .31
8.6 Safety data sheet .31
9 Packaging and marking .31
10 Ordering information.31
Annex A (informative) Engineering information .33
A.1 Chemical properties.33
A.2 Electrical properties.33
A.3 Flammability properties.33
A.4 Mechanical properties.33
A.5 Physical properties .35
A.6 Thermal properties .35

---------------------- Page: 6 ----------------------

61249-2-23 © IEC:2005 – 5 –
Table 1 – Electrical properties.17
Table 2 – Nominal thickness and tolerance of metal-clad laminate .21
Table 3 –Bow and twist .23
Table 4 – Pull-off and peel strength.23
Table 5 – Size tolerance for cut panels.25
Table 6 – Rectangularity of cut panels.25
Table 7 – Flexural strength .27
Table 8 – Flammability, vertical burning test .27
Table 9 – Water absorption .29

---------------------- Page: 7 ----------------------

61249-2-23 © IEC:2005 – 7 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
MATERIALS FOR PRINTED BOARDS AND OTHER
INTERCONNECTING STRUCTURES –
Part 2-23: Reinforced base materials, clad and unclad –
Non-halogenated phenolic cellulose paper
reinforced laminated sheets, economic grade, copper clad
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61249-2-23 has been prepared by IEC technical committee 91:
Electronics assembly technology.
The text of this standard is based on the following documents:
FDIS Report on voting
91/495/FDIS 91/505/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 8 ----------------------

61249-2-23 © IEC:2005 – 9 –
IEC 61249-2 consists of the following parts, under the general title Materials for printed
boards and other interconnecting structures – Part 2: Reinforced base materials, clad and
unclad:
Part 2-1: Phenolic cellulose paper reinforced laminated sheets, economic grade, copper
clad
Part 2-2: Phenolic cellulose paper reinforced laminated sheets, high electrical grade,
copper-clad
Part 2-4: Polyester non-woven/woven fibreglass laminated sheets of defined flammability
(vertical burning test), copper-clad
Part 2-5: Brominated epoxide cellulose paper reinforced core/woven E-glass reinforced
surfaces laminate sheets of defined flammability (vertical burning test), copper-
clad
Part 2-6: Brominated epoxide non-woven/woven, E-glass reinforced laminated sheets of
defined flammability (vertical burning test), copper-clad
Part 2-7: Epoxide woven E-glass laminated sheet of defined flammability (vertical burning
test), copper-clad
Part 2-8: Modified brominated epoxide woven fibreglass reinforced laminated sheets of
defined flammability (vertical burning test), copper-clad
Part 2-9: Bismaleimide/triazine, modified epoxide or unmodified, woven E-glass reinforced
laminated sheets of defined flammability (vertical burning test), copper-clad
Part 2-10: Cyanate ester, brominated epoxide, modified or unmodified, woven E-glass
reinforced laminated sheets of defined flammability (vertical burning test), copper-
clad
Part 2-11: Polyimide, brominated epoxide modified or unmodified, woven E-glass reinforced
laminated sheets of defined flammability (vertical burning test), copper-clad
Part 2-12: Epoxide non-woven aramid laminate of defined flammability, copper-clad
Part 2-13: Cyanate ester non-woven aramid laminate of defined flammability, copper-clad
Part 2-18: Polyester non-woven fibreglass reinforced laminated sheet of defined flammability
(vertical burning test), copper-clad
Part 2-19: Epoxide cross-plied linear fibreglass-reinforced laminated sheets of defined flam-
mability (vertical burning test), copper-clad
Part 2-21: Non-halogenated epoxide woven E-glass reinforced laminated sheets of defined
flammability (vertical burning test), copper-clad
Part 2-22: Modified non-halogenated epoxide woven E-glass laminated sheets of defined
flammablity (vertical burning test), copper
...