SIST EN ISO 9455-11:2018
(Main)Soft soldering fluxes - Test methods - Part 11: Solubility of flux residues (ISO 9455-11:2017)
Soft soldering fluxes - Test methods - Part 11: Solubility of flux residues (ISO 9455-11:2017)
This document specifies a qualitative method for assessing the solubility of flux residues in a selected
solvent. The method is applicable to all fluxes of Type 1, as defined in ISO 9454-1.
NOTE This test gives no assurance that post-cleaning residues, which may be present in sufficiently small
amounts to pass the test, will not be detrimental to the soldered assembly in the long term.
Flussmittel zum Weichlöten - Prüfverfahren - Teil 11: Löslichkeit von Flussmittelrückständen (ISO 9455-11:2017)
Dieser Teil der ISO 9455 legt ein qualitatives Verfahren zur Prüfung der Löslichkeit von Flussmittelrückständen in einem ausgewählten Lösungsmittel fest. Dieses Verfahren ist anwendbar für alle Flussmittel des Typs 1 nach ISO 9454-1.
ANMERKUNG Diese Prüfung gibt keine Zusicherung, dass das Nachreinigen der Rückstände, die in ausreichenden kleinen Mengen vorliegen können um die Prüfung zu bestehen, sich langfristig nicht nachteilig auf die gelöteten Teile auswirken.
Flux de brasage tendre - Méthodes d'essai - Partie 11: Solubilité des résidus de flux (ISO 9455-11:2017)
ISO 9455-11:2017 spécifie une méthode quantitative d'évaluation de la solubilité des résidus de flux dans un solvant choisi. La méthode est applicable à tous les flux de type 1 définis dans l'ISO 9454‑1.
Talila za mehko spajkanje - Preskusne metode - 11. del: Topnost ostankov talila (ISO 9455-11:2017)
Ta dokument določa kvalitativno metodo za ocenjevanje topnosti ostankov talila v izbranem topilu. Ta metoda se uporablja za vsa talila tipa 1 iz standarda ISO 9454-1.
OPOMBA: Ta preskus ne zagotavlja, da ostanki talila, ki so lahko po čiščenju prisotni v dovolj majhnih
količinah, da je preizkus uspešno opravljen, ne bodo dolgoročno škodovali spajkanemu sestavu.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 9455-11:2018
01-februar-2018
1DGRPHãþD
SIST EN 29455-11:1998
Talila za mehko spajkanje - Preskusne metode - 11. del: Topnost ostankov talila
(ISO 9455-11:2017)
Soft soldering fluxes - Test methods - Part 11: Solubility of flux residues (ISO 9455-
11:2017)
Flussmittel zum Weichlöten - Prüfverfahren - Teil 11: Löslichkeit von
Flussmittelrückständen (ISO 9455-11:2017)
Flux de brasage tendre - Méthodes d'essai - Partie 11: Solubilité des résidus de flux (ISO
9455-11:2017)
Ta slovenski standard je istoveten z: EN ISO 9455-11:2017
ICS:
25.160.50 Trdo in mehko lotanje Brazing and soldering
SIST EN ISO 9455-11:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 9455-11:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 9455-11:2018
EN ISO 9455-11
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2017
EUROPÄISCHE NORM
ICS 25.160.50 Supersedes EN 29455-11:1993
English Version
Soft soldering fluxes - Test methods - Part 11: Solubility of
flux residues (ISO 9455-11:2017)
Flux de brasage tendre - Méthodes d'essai - Partie 11: Flussmittel zum Weichlöten - Prüfverfahren - Teil 11:
Solubilité des résidus de flux (ISO 9455-11:2017) Löslichkeit von Flussmittelrückständen (ISO 9455-
11:2017)
This European Standard was approved by CEN on 12 September 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9455-11:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 9455-11:2018
EN ISO 9455-11:2017 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 9455-11:2018
EN ISO 9455-11:2017 (E)
European foreword
This document (EN ISO 9455-11:2017) has been prepared by Technical Committee ISO/TC 44 “Welding
and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2018, and conflicting national standards shall
be withdrawn at the latest by March 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 29455-11:1993.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 9455-11:2017 has been approved by CEN as EN ISO 9455-11:2017 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 9455-11:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 9455-11:2018
INTERNATIONAL ISO
STANDARD 9455-11
Second edition
2017-08
Soft soldering fluxes — Test
methods —
Part 11:
Solubility of flux residues
Flux de brasage tendre — Méthodes d’essai —
Partie 11: Solubilité des résidus de flux
Reference number
ISO 9455-11:2017(E)
©
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 9455-11:2018
ISO 9455-11:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 9455-11:2018
ISO 9455-11:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Reagents and materials . 1
6 Apparatus . 3
7 Procedure. 3
8 Assessment of results . 4
9 Test report . 4
© ISO 2017 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 9455-11:2018
ISO 9455-11:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patent
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.