kSIST FprEN 12814-8:2024
(Main)Testing of welded joints of thermoplastics semi-finished products - Part 8: Requirements
Testing of welded joints of thermoplastics semi-finished products - Part 8: Requirements
This document provides the requirements for the tests made on welded thermoplastics semi-finished products.
The selection of the appropriate test method(s) is made in accordance with the particular type and application of welded product.
The test results depend on the conditions of manufacture for the test specimen and on the test conditions. They can therefore only be related to the behaviour of the product or can only be used for designing a structure, if the test conditions can be related to the service conditions.
Prüfen von Schweißverbindungen aus thermoplastischen Kunststoffen - Teil 8: Anforderungen
In diesem Dokument werden Anforderungen an Prüfungen festgelegt, die an Schweißverbindungen aus thermoplastischen Kunststoffen durchgeführt werden.
Die Wahl des zweckmäßigen Prüfverfahrens wird entsprechend der jeweiligen Ausführung und Anwendung des geschweißten Produkts getroffen.
Die Prüfergebnisse sind von den Herstellbedingungen für die Probekörper und von den Prüfbedingungen abhängig. Sie können deshalb auf das Verhalten der Erzeugnisse oder für die Berechnung einer Konstruktion nur übertragbar sein, wenn die auftretenden Praxisbeanspruchungen den Prüfbedingungen entsprechen.
Essais des assemblages soudés sur produits semi-finis en thermoplastiques - Partie 8 : Exigences
Le présent document définit les exigences pour les essais réalisés sur les produits semi-finis soudés en thermoplastiques.
Le choix de la (des) méthode(s) d’essai appropriée(s) est fait conformément au type particulier et à l’application du produit soudé.
Les résultats des essais dépendent des conditions d’élaboration pour les éprouvettes et des conditions d’essai. Ils ne peuvent donc être liés qu'au comportement du produit ou ne peuvent être utilisés pour la conception d'une structure que si les conditions d'essai peuvent être liées aux conditions de service.
Preskušanje zvarjenih spojev plastomernih polizdelkov - 8. del: Zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 12814-8:2023
01-september-2023
Nadomešča:
SIST EN 12814-8:2021
Preskušanje zvarjenih spojev plastomernih polizdelkov - 8. del: Zahteve
Testing of welded joints of thermoplastics semi-finished products - Part 8: Requirements
Prüfen von Schweißverbindungen aus thermoplastischen Kunststoffen - Teil 8:
Anforderungen
Essais des assemblages soudés sur produits semi-finis en thermoplastiques - Partie 8 :
Exigences
Ta slovenski standard je istoveten z: prEN 12814-8
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN 12814-8:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN 12814-8:2023
oSIST prEN 12814-8:2023
DRAFT
EUROPEAN STANDARD
prEN 12814-8
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2023
ICS 25.160.40 Will supersede EN 12814-8:2021
English Version
Testing of welded joints of thermoplastics semi-finished
products - Part 8: Requirements
Essais des assemblages soudés sur produits semi-finis Prüfen von Schweißverbindungen aus
en thermoplastiques - Partie 8 : Exigences thermoplastischen Kunststoffen - Teil 8:
Anforderungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 249.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12814-8:2023 E
worldwide for CEN national Members.
oSIST prEN 12814-8:2023
prEN 12814-8:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms, definitions, symbols and abbreviations . 4
3.1 Terms and definitions . 4
3.2 Symbols and abbreviations . 5
4 Materials and properties . 5
5 Destructive test methods . 5
6 Requirements . 6
6.1 General. 6
6.2 Bend test . 6
6.3 Tensile test . 20
6.4 Tensile creep test . 20
6.5 Peel tests . 20
6.6 Macroscopic examination . 20
6.7 Low temperature tensile test . 20
6.8 Tensile test with waisted test specimen . 21
oSIST prEN 12814-8:2023
prEN 12814-8:2023 (E)
European foreword
This document (prEN 12814-8:2023) has been prepared by Technical Committee CEN/TC 249 “Plastics”,
the secretariat of which is held by SIS.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12814-8:2021.
The main changes compared to the previous edition are listed below:
— bend angle data and ram displacement requirements as well as tensile requirements for PA-U have
been added.
oSIST prEN 12814-8:2023
prEN 12814-8:2023 (E)
1 Scope
This document provides the requirements for the tests made on welded thermoplastics semi-finished
products.
The selection of the appropriate test method(s) is made in accordance with the particular type and
application of welded product.
The test results depend on the conditions of manufacture for the test specimen and on the test conditions.
They can therefore only be related to the behaviour of the product or can only be used for designing a
structure, if the test conditions can be related to the service conditions.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 12814-1, Testing of welded joints of thermoplastics semi-finished products - Part 1: Bend test
EN 12814-2, Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test
EN 12814-3, Testing of welded joints in thermoplastics semi-finished products - Part 3: Tensile creep test
EN 12814-4, Testing of welded joints of thermoplastics semi-finished products - Part 4: Peel test
EN 12814-5, Testing of welded joints of thermoplastics semi-finished products - Part 5: Macroscopic
examination
EN 12814-6, Testing of welded joints of thermoplastics semi-finished products - Part 6: Low temperature
tensile test
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.