SIST EN 15566:2016
(Main)Railway applications - Railway rolling stock - Draw gear and screw coupling
Railway applications - Railway rolling stock - Draw gear and screw coupling
This standard specifies the requirement of the draw gear and screw coupling for the end rolling stock that have to couple with other interoperable rolling stock (freight wagons, locomotives, passenger vehicles ...).
This standard covers the functionality, construction, interfaces and testing including pass/fail criteria for draw gear and screw coupling.
The standard describes three categories of classification of draw gear and screw coupling, (1 MN, 1,2 MN and 1,5 MN).
Bahnanwendungen - Schienenfahrzeuge - Zugeinrichtung und Schraubenkupplung
Diese Norm legt die Anforderungen an Zugeinrichtungen und Schraubenkupplungen für Endwagen fest, die mit anderen Schienenfahrzeugen des grenzüberschreitenden Verkehrs (Güterwagen, Lokomotiven, Reise-zugwagen ...) gekuppelt werden.
Diese Norm umfasst die Funktionalität, Bauweise, Schnittstellen und Prüfungen einschließlich der Abnahme-kriterien für Zugeinrichtungen und Schraubenkupplungen.
In dieser Norm sind drei Kategorien von Zugeinrichtungen und Schraubenkupplungen beschrieben (1 MN, 1,2 MN und 1,5 MN).
Applications ferroviaires - Matériel roulant ferroviaire - Organes de traction et tendeur d'attelage
La présente norme spécifie les exigences relatives aux organes de traction et tendeurs d'attelage pour un matériel roulant devant être couplé à un autre matériel roulant interopérable (wagons de marchandises, locomotives, voitures, etc.).
La présente norme couvre la fonctionnalité, la construction, les interfaces et les essais, y compris les critères de réussite/d'échec aux essais pour les organes de traction et les tendeurs d'attelage.
La norme décrit trois catégories pour les organes de traction et les tendeurs d'attelage (1 MN, 1,2 MN et 1,5 MN).
Železniške naprave - Železniška vozila - Vlečna naprava in vijačna spenjača
Ta standard določa zahtevo za vlečno napravo in vijačno spenjačo končnega vozila, ki se mora speti z drugimi interoperabilnimi vozili (tovorni vagoni, lokomotive, potniška vozila, ...).
Ta standard zajema funkcionalnost, sestavo, vmesnike in preskušanje, vključno z merili za uspešno/neuspešno opravljen preskus, za vlečno napravo in vijačno spenjačo.
Standard opisuje tri razvrstitvene kategorije vlečne naprave in vijačne spenjače (1 MN, 1,2 MN in 1,5 MN).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 15566:2016
01-november-2016
1DGRPHãþD
SIST EN 15566:2009+A1:2010
äHOH]QLãNHQDSUDYHäHOH]QLãNDYR]LOD9OHþQDQDSUDYDLQYLMDþQDVSHQMDþD
Railway applications - Railway rolling stock - Draw gear and screw coupling
Bahnanwendungen - Schienenfahrzeuge - Zugeinrichtung und Schraubenkupplung
Applications ferroviaires - Matériel roulant ferroviaire - Organes de traction et tendeur
d'attelage
Ta slovenski standard je istoveten z: EN 15566:2016
ICS:
45.060.10 9OHþQDYR]LOD Tractive stock
SIST EN 15566:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 15566:2016
---------------------- Page: 2 ----------------------
SIST EN 15566:2016
EN 15566
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2016
EUROPÄISCHE NORM
ICS 45.060.01 Supersedes EN 15566:2009+A1:2010
English Version
Railway applications - Railway rolling stock - Draw gear
and screw coupling
Applications ferroviaires - Matériel roulant ferroviaire Bahnanwendungen - Schienenfahrzeuge -
- Organes de traction et tendeur d'attelage Zugeinrichtung und Schraubenkupplung
This European Standard was approved by CEN on 8 July 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15566:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 15566:2016
EN 15566:2016 (E)
Contents Page
European foreword . 7
Introduction . 9
1 Scope . 10
2 Normative references . 10
3 Terms and definitions . 11
4 Requirements for all types of draw gear and screw coupling. 13
4.1 Classification and designation . 13
4.2 Interaction coupling/buffer . 13
4.3 Interface dimension for freight wagons. 14
4.4 Life time . 15
5 Draw gear . 16
5.1 Draw gear components . 16
5.2 Draw hook and drawbar – Requirements . 18
6 Screw coupling . 18
6.1 General requirements . 18
6.2 Screw coupling – Requirements. 20
7 Elastic device . 20
7.1 Characteristics of elastic device . 20
7.2 Elastic device – Requirements . 21
Annex A (normative) Dynamic test (fatigue test) procedure . 22
A.1 Background . 22
A.2 Performance of the test . 22
A.2.1 Conditioning . 22
A.2.2 Dynamic test (fatigue test) . 22
A.2.3 Non-destructive tests . 24
A.2.4 Determination of residual strength . 24
A.2.5 Macrographic and Micrographic tests . 24
A.3 Criteria of acceptance . 24
Annex B (normative) Draw hook – dimensions. 25
Annex C (normative) Draw gear – Interface dimension . 26
Annex D (normative) Screw coupling components – dimensions . 27
Annex E (normative) Draw hook and drawbar – Requirements . 29
E.1 Physical characteristics . 29
E.1.1 Appearance . 29
E.1.2 Integrity . 29
2
---------------------- Page: 4 ----------------------
SIST EN 15566:2016
EN 15566:2016 (E)
E.1.3 Material examination . 29
E.2 Geometrical characteristics . 30
E.3 Mechanical characteristics . 30
E.3.1 Tensile test on test piece . 30
E.3.2 Resilience. 30
E.3.3 Hardness . 30
E.3.4 Tensile test on draw hook and draw bar . 30
E.3.5 Compressive test on draw hook for locomotives . 31
E.4 Marking . 31
E.5 Manufacture. 31
E.5.1 General on draw bars . 31
E.5.2 General on draw hooks . 31
E.5.3 Machining . 31
E.5.4 Heat treatment . 31
E.5.5 Rectification of defects. 32
E.6 Acceptance . 32
E.6.1 General . 32
E.6.2 Inspection of the draw hooks . 32
E.6.3 Inspection of draw bars . 37
E.6.4 Conclusion of the inspections . 38
E.7 Delivery . 38
E.7.1 Protection against oxidation . 38
E.7.2 Packaging . 38
Annex F (normative) Screw coupling and component parts – Requirements . 39
F.1 Material . 39
F.2 Physical characteristics . 39
F.2.1 Appearance . 39
F.2.2 Soundness . 39
F.2.3 Additional requirements for screw couplings . 40
F.3 Geometrical characteristics . 40
F.3.1 General . 40
F.3.2 Dimensions limited either by two unmachined or rough-machined surfaces or by
one unmachined or rough-machined surface . 40
F.3.3 Dimensions limited by two machined surfaces . 41
F.4 Mechanical characteristics . 41
F.4.1 Heat treatment . 41
F.4.2 Hardness . 41
3
---------------------- Page: 5 ----------------------
SIST EN 15566:2016
EN 15566:2016 (E)
F.4.3 Values for predetermined breaking loads for the weakest part. 41
F.4.4 Resilience . 42
F.4.5 Requirements for screw coupling . 42
F.4.6 Requirement for handle and trunnion . 43
F.5 Marking . 44
F.6 Manufacture . 44
F.6.1 Preparation of the materials . 44
F.6.2 Manufacture of the component parts . 44
F.7 Acceptance . 46
F.7.1 General . 46
F.7.2 Inspection of the manufacture . 46
F.8 Inspection of the materials, component parts and screw couplings . 46
F.8.1 Materials submission for acceptance . 46
F.8.2 Grouping into batches . 47
F.8.3 Nature and proportion of the tests . 47
F.8.4 Sampling and preparation of the samples and test pieces . 48
F.8.5 Carrying out of the checks and tests . 52
F.9 Completion of inspections. 53
F.10 Delivery. 54
F.10.1 Protection against oxidation . 54
F.10.2 Packing . 54
Annex G (normative) Elastic device – Requirements . 55
G.1 Rubber elastomer or other elastomer elastic device . 55
G.1.1 General . 55
G.1.2 Metal inserts requirements . 55
G.1.3 Elastomer requirements . 55
G.1.4 Static test . 57
G.1.5 Endurance test . 58
G.1.6 Bonding . 59
G.1.7 Inspection and Tests . 59
G.1.8 Markings . 60
G.2 Friction spring/Ring spring . 61
G.2.1 Manufacturer's marks . 61
G.2.2 Flexibility test . 61
G.2.3 Endurance test . 62
Annex H (normative) Marking . 63
4
---------------------- Page: 6 ----------------------
SIST EN 15566:2016
EN 15566:2016 (E)
H.1 General . 63
H.2 Marking of the screw coupling . 63
H.3 Draw gear . 64
H.4 Draw bar . 64
H.5 Summary of markings . 65
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2008/57/EC . 66
Bibliography . 68
Figures
Figure 1 — Force-stroke diagram for stored and absorbed energy . 12
Figure 2 — Support plate ― Interface dimension for freight wagons . 15
Figure 3 — Draw gear ― Assembly . 17
Figure 4 — Standard screw coupling with non-loosening hinged ball handle . 19
Figure 5 — Standard screw coupling with hinged handle with non-loosening upper rest . 20
Figure A.1 — Example of Load cycles Step 1 and Step 2 . 23
Figure B.1 — Draw hook . 25
Figure C.1 — Drawbar with “fork” and safety device . 26
Figure C.2 — Joint pin . 26
Figure D.1 — Coupling hook pin . 27
Figure D.4 — Shackle . 28
Figure E.1 — Location of the test samples . 34
Figure E.2 — Marking of the draw hook for the tensile test . 35
Figure E.3 — Location of the test samples . 37
Figure F.1 — Location of the measurement of the deformation of the screw coupling . 42
Figure F.2 — Test facility for the tensile test of the screw coupling . 43
Figure F.3 — Measurement of the screw coupling . 43
Figure F.4 — Permitted depth of the fold in thread profile . 45
Figure F.5 — Screw – test sample location . 49
Figure F.6 — Shackle – test sample location . 50
Figure F.7 — Coupling link – test sample location . 50
Figure F.8 — Trunnion nut (link fitting) – test sample location . 51
Figure F.9 — Trunnion nut (shackle fitting) – test sample location . 51
Figure F.10 — Pin – test sample location . 52
Figure G.1 — Elastic device – load cycle for endurance test . 58
Figure G.2 — Elastic device – Set up for endurance test . 59
Figure H.1 — Location of mark . 64
Figure H.2 — Mark dimension . 64
5
---------------------- Page: 7 ----------------------
SIST EN 15566:2016
EN 15566:2016 (E)
Tables
Table 1 — Classification of coupling by designation of the minimum breaking load . 13
Table A.1 — Pre-loading values . 22
Table A.2 — Condition of dynamic tests for all parts except screw coupling . 23
Table A.3 — Condition of dynamic tests for screw coupling . 24
Table E.1 — Requirements . 30
Table E.2 — Checks and tests . 33
Table F.1 — Requirements . 40
Table F.2 — load of link . 41
Table F.3 — Breaking load screw . 41
Table F.4 — Proportion of the tests – Finished products and component parts . 48
Table G.1 — Characteristics of the constituents . 55
Table G.2 — Nature of inspections and tests . 60
Table G.3 — Number of flexibility tests per batch of springs . 62
Table H.1 — Marking . 65
Table ZA.1 — Correspondence between this European Standard, the Commission
Regulation concerning the technical specification for interoperability relating to the
subsystem ‘rolling stock – freight wagons’ of the rail system in the European Union
and repealing Commission Decision 321/2013/EC, as amended by Commission
Regulation (EU) 2015/924 (published in the Official Journal L 150, 17.06.2015,
p.10); and Directive 2016/797/EC . 66
Table ZA.2 — Correspondence between this European Standard, the Commission regulation
(EU) No 1302/2014 of 18 November 2014 concerning the technical specification for
interoperability relating to the ‘rolling stock locomotives and passenger rolling
stock’ of the rail system in the European Union (published in the Official Journal L
356, 12.12.2014, p.228) and Directive 2008/57/EC . 67
6
---------------------- Page: 8 ----------------------
SIST EN 15566:2016
EN 15566:2016 (E)
European foreword
This document (EN 15566:2016) has been prepared by Technical Committee CEN/TC 256 “Railway
applications”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2017, and conflicting national standards shall
be withdrawn at the latest by March 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15566:2009+A1:2010.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2008/57/EC.
For relationship with EU Directive 2008/57/EC, see informative Annex ZA, which is an integral part of
this document.
Modifications
Compared with EN 15566:2009+A1:2010 the following main changes have been done:
a) checking and revision of Clause 2 – Normative references;
b) modification in Clause 3 – working capacity (3.8) was deleted and intermediate coupling system for
permanent coupled wagons now defined as permanent coupling system;
c) in Clause 4, requirements for compressive loads for draw hook and draw gear rationalised and
explained;
d) in Clause 7,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.