SIST EN 1301-1:2008
(Main)Aluminium and aluminium alloys - Drawn wire - Part 1: Technical conditions for inspection and delivery
- Abstract
This document specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy drawn wire for general engineering applications.
It does not apply for aeronautical application.
It applies to drawn wires, except for electrical or welding purposes.
It does not apply to drawing stock.
- Status
- Published
- Publication Date
- 05-Oct-2008
- Technical Committee
- INEK - Nonferrous metals
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 24-Sep-2008
- Due Date
- 29-Nov-2008
- Completion Date
- 06-Oct-2008
SIST EN 1301-1:2008 is the Slovenian standard identical to EN 1301-1:2008, issued through SIST from CEN. It sets the inspection and delivery conditions for aluminium and aluminium alloy drawn wire used in general engineering applications, so buyers, manufacturers and quality staff know what to order, test and document.
What does SIST EN 1301-1:2008 specify?
SIST EN 1301-1:2008 specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy drawn wire for general engineering applications. It applies to drawn wire, but not to aeronautical applications, electrical or welding purposes, or drawing stock.
The document is organized into clauses on scope, normative references, terms and definitions, ordering information, requirements, test procedure, delivery and inspection documents, marking, packaging and complaints of non-conformity. In practice, that means it covers the whole supply chain from the purchase order to final acceptance.
What are the key requirements of SIST EN 1301-1:2008?
Ordering and product definition
- Clause 4 requires the order to identify the product form, alloy designation, temper, dimensions, tolerances, quantity and any required certificates. This matters because the supplier is only bound to what is stated on the order.
- The order can also set special requirements for testing, marking, surface quality and packaging. That gives the purchaser a way to tighten control where the application needs it.
Material, properties and condition
- Clause 5.3 requires the chemical composition to conform to EN 573-3, unless tighter limits are agreed on the order. For a buyer, this is the key control on alloy identity and impurity limits.
- Clause 5.4 requires mechanical properties to conform to EN 1301-2 or to agreed properties stated on the order. This links the delivery standard to the strength and ductility level needed in use.
- Clause 5.6 requires dimensional tolerances to conform to EN 1301-3. That is what keeps the wire usable in downstream forming, assembly or machining.
- Clause 5.8 ties the temper of delivery to EN 515 and identifies the usual tempers as O, H and T. In practice, the temper tells the purchaser how hard the wire is and how it will behave in processing.
Inspection, testing and acceptance
- Clause 5.2 makes the manufacturer responsible for inspection and testing before shipment, and allows purchaser inspection at the works if it is notified in the order. This sets the point where acceptance checks happen.
- Clause 6.1 defines how samples and test pieces are taken and identified, including chemical-analysis samples taken at casting and tensile-test pieces traced to the inspection lot. That traceability matters when a result must be linked back to a specific coil or batch.
- Clause 6.2 specifies the test methods: tensile testing according to EN 10002-1, dimensional checks at ambient temperature, and surface inspection before delivery without magnification unless otherwise specified. If there is a dispute on chemical composition, referee analysis uses the methods cited in the document.
- Clause 6.3 sets the retest rules when a specimen fails. This protects both sides by showing when a result is a test error and when a lot must be rejected or retreated.
Delivery documents and handling of disputes
- Clause 7 requires a certificate of mass and analysis with each delivery, and an inspection certificate 3.1 according to EN 10204 unless the order says otherwise. These documents are the main evidence of conformity.
- Clauses 8 to 10 cover marking, packaging and complaints of non-conformity, including arbitration by mutual agreement if conformity is disputed. That gives a formal path for resolving disagreements before rejection.
What terms does SIST EN 1301-1:2008 define?
- Temper of delivery - the supplied condition of the wire, such as O, H or T, which affects processing and final properties.
- Inspection certificate 3.1 - the EN 10204 document that reports at least chemical analysis and mechanical properties for the delivered product.
- Certificate of mass and analysis - the delivery document listing supplier, purchaser, product description, cast numbers, analysis and total net mass.
- Inspection lot - the group from which test pieces are taken and against which conformity is judged.
- Referee analysis - the dispute-analysis method used when chemical composition is contested.
- Drawn wire - wire produced by drawing and covered here only for general engineering use.
Who uses SIST EN 1301-1:2008?
Manufacturers of aluminium wire use SIST EN 1301-1:2008 to set production, testing and documentation for delivery. Purchasers, buyers and quality managers use it to specify the alloy, temper, dimensions, tolerances and certificates they need.
Testing laboratories and inspection staff use it for sampling, tensile testing, dimensional checks and chemical-analysis traceability. It is relevant in aluminium products supply chains where wire is ordered for general engineering applications.
What changed in SIST EN 1301-1:2008 from the previous edition?
SIST EN 1301-1:2008 supersedes EN 1301-1:1997. The foreword states that, besides editorial updates and refreshed normative references, the following changes were made:
- EN 12258-1:1998 and EN 14361 were added to Clause 2.
- Clause 3 was replaced by a reference to EN 12258-1:1998.
- Clause 6.1.2 and 6.1.3 were modified.
- Clause 7 was completely revised.
Which standards are used with SIST EN 1301-1:2008?
| Standard | Role in SIST EN 1301-1:2008 |
|---|---|
| EN 515 | Gives temper designations used for delivery condition |
| EN 573-3 | Sets chemical composition for aluminium and aluminium alloy wrought products |
| EN 1301-2 | Gives the mechanical properties for drawn wire |
| EN 1301-3 | Gives dimensional tolerances for drawn wire |
| EN 10002-1 | Specifies the tensile test method at ambient temperature |
| EN 10204 | Defines inspection documents, including inspection certificate 3.1 |
| EN 12258-1:1998 | Supplies the general terms and definitions used in Clause 3 |
| EN 14361 | Gives sampling for chemical analysis from metal melts |
| EN 14242 | Cited for referee chemical analysis in disputes |
| EN 14726 | Cited for referee chemical analysis in disputes |
What does the SIST EN 1301-1:2008 document contain?
SIST EN 1301-1:2008 contains the ordering information, material requirements, sampling rules, test methods, document requirements, marking, packaging and complaint procedure for aluminium and aluminium alloy drawn wire. It also points to the related EN 1301 parts for mechanical properties and dimensional tolerances, and to test standards used when extra tests or dispute analysis are needed.
Relations
- Effective Date
- 01-Nov-2008
- Effective Date
- 25-Mar-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Refers
SIST EN 14361:2025 - Aluminium and aluminium alloys - Chemical analysis - Sampling from metal melts - Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Referred By
SIST EN 1301-2:2008 - Aluminium and aluminium alloys - Drawn wire - Part 2: Mechanical properties - Effective Date
- 28-Jan-2026
- Referred By
SIST EN 1301-3:2008 - Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions - Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
Get Certified
Connect with accredited certification bodies for this standard
Element Materials Technology
Materials testing and product certification.
Inštitut za kovinske materiale in tehnologije
Institute of Metals and Technology. Materials testing, metallurgical analysis, NDT.
Sponsored listings
Frequently Asked Questions
SIST EN 1301-1:2008 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Aluminium and aluminium alloys - Drawn wire - Part 1: Technical conditions for inspection and delivery". This standard covers: This document specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy drawn wire for general engineering applications. It does not apply for aeronautical application. It applies to drawn wires, except for electrical or welding purposes. It does not apply to drawing stock.
This document specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy drawn wire for general engineering applications. It does not apply for aeronautical application. It applies to drawn wires, except for electrical or welding purposes. It does not apply to drawing stock.
SIST EN 1301-1:2008 is classified under the following ICS (International Classification for Standards) categories: 77.150.10 - Aluminium products. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 1301-1:2008 has the following relationships with other standards: It is inter standard links to SIST EN 1301-1:1998, SIST EN 573-3:2026, SIST EN 573-3:2019+A2:2024, SIST EN 12258-1:1999, SIST EN 10204:2004, SIST EN 14361:2025, SIST EN ISO 6892-1:2020, SIST EN 515:2017, SIST EN 1301-2:2008, SIST EN 1301-3:2008, SIST EN 15088:2006, SIST EN 1090-3:2008, SIST EN 1090-3:2019, SIST EN 13195:2014, SIST EN 13195:2010. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 1301-1:2008 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.GREDYRAluminium und Aluminiumlegierungen - Gezogene Drähte - Teil 1: Technische LieferbedingungenAluminium et alliages d'aluminium - Fil étiré - Partie 1: Conditions techniques de contrôle et de livraisonAluminium and aluminium alloys - Drawn wire - Part 1: Technical conditions for inspection and delivery77.150.10Aluminijski izdelkiAluminium productsICS:Ta slovenski standard je istoveten z:EN 1301-1:2008SIST EN 1301-1:2008en,fr,de01-november-2008SIST EN 1301-1:2008SLOVENSKI
STANDARDSIST EN 1301-1:19981DGRPHãþD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1301-1September 2008ICS 77.150.10Supersedes EN 1301-1:1997
English VersionAluminium and aluminium alloys - Drawn wire - Part 1: Technicalconditions for inspection and deliveryAluminium et alliages d'aluminium - Fil étiré - Partie 1 :Conditions techniques de contrôle et de livraisonAluminium und Aluminiumlegierungen - Gezogene Drähte -Teil 1: Technische LieferbedingungenThis European Standard was approved by CEN on 16 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1301-1:2008: ESIST EN 1301-1:2008
Foreword : amended; Clause 2: EN 12258-1:1998 and EN 14361 added; Clause 3: subclauses 3.1 to 3.9 deleted and replaced by reference to EN 12258-1:1998; Clause 6: subclauses 6.1.2 and 6.1.3 modified; Clause 7: completely revised. EN 1301 comprises the following parts under the general title: "Aluminium and aluminium alloys – Drawn wire": Part 1: Technical conditions for inspection and delivery Part 2 : Mechanical properties Part 3 : Tolerances on dimensions According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
...