SIST EN ISO 15609-5:2011

Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding (ISO 15609-5:2011)

ISO 15609-5:2011 specifies requirements for the content of welding procedure specifications for resistance spot, seam, butt and projection welding processes. It is necessary to establish the acceptability of applying the principles of ISO 15609-5:2011 to other resistance and related welding processes before any qualification is undertaken.
Variables listed in ISO 15609-5:2011 are those influencing either weld dimensions (quality), weld nugget dimension, weld pattern positioning, mechanical properties or geometry of the welded joint.

Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe - Schweißanweisung - Teil 5: Widerstandsschweißen (ISO 15609-5:2011)

Diese Norm legt die Anforderungen an den Inhalt der Schweißanweisungen für Widerstandspunkt-, Rollennaht-, Pressstumpf- und Buckel-Schweißprozesse fest. Die Eignung der verwendeten Grundsätze dieser Norm für andere Widerstands- sowie verwandte Schweißprozesse sollte, bevor irgendeine Qualifizierung übernommen wird, nachgewiesen werden.
Diese Norm ist Teil einer Normenreihe. EN ISO 15607:2003, Anhang A, gibt Einzelheiten dieser Normenreihe wieder.
Die in der Norm aufgeführten veränderlichen Größen beeinflussen entweder die Abmessungen der Schweißungen (Qualität), die Größe der Schweißlinse beziehungsweise die Festlegung des Schweißnaht-verlaufes, die mechanischen Eigenschaften oder die Geometrie der Schweißverbindung.

Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Descriptif d'un mode opératoire de soudage - Partie 5: Soudage par résistance (ISO 15609-5:2011)

L'ISO 15609-5:2011 spécifie les exigences relatives au contenu des descriptifs de modes opératoires de soudage pour les procédés de soudage par résistance par points, à la molette, en bout et par bossages. La vérification de la possibilité d'appliquer les principes de l'ISO 15609-5:2011 à d'autres procédés de soudage par résistance ou assimilés se fait avant d'entreprendre toute qualification.
Les variables énumérées dans l'ISO 15609-5:2011 sont celles qui ont une influence soit sur les dimensions de la soudure (qualité), les dimensions du noyau de la soudure, la configuration des soudures, les caractéristiques mécaniques ou la géométrie de l'assemblage soudé.

Popis in kvalifikacija varilnih postopkov za kovinske materiale - Specifikacija varilnega postopka - 5. del: (Elektro)uporovno varjenje (ISO 15609-5:2011)

Ta standard določa zahteve za vsebino specifikacij varilnega postopka za (elektro)uporovno točkovno, kolutno, soležno in bradavično varjenje. Sprejemljivost uporabe načel standarda pri drugih (elektro)uporovnih in sorodnih varilnih procesih se mora ugotoviti pred izvedbo kvalifikacij. Ta standard je del serije standardov. Podrobnosti o tej seriji so navedene v ISO 15607:2003, dodatek A. Spremenljivke, navedene v tem standardu, vplivajo na mere (kakovost) zvarov, mere zvarnega zrna, položaj zvarnega vzorca, mehanske lastnosti ali geometrijo zvarnega spoja.

General Information

• Status: Published
• Public Enquiry End Date: 24-Sep-2010
• Publication Date: 24-Oct-2011
• ICS: 25.160.10 - Welding processes
• Technical Committee: VAR - Welding
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 12-Oct-2011
• Due Date: 17-Dec-2011
• Completion Date: 25-Oct-2011
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: EN ISO 15609-5:2011 - Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding (ISO 15609-5:2011, Corrected version 2011-12-01)

Relations

• Replaces: SIST EN ISO 15609-5:2004 - Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding (ISO 15609-5:2004)
• Effective Date: 01-Dec-2011
• Replaces: SIST EN ISO 15609-5:2004 - Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding (ISO 15609-5:2004)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15609-5:2011
01-december-2011
1DGRPHãþD
SIST EN ISO 15609-5:2004
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Specifikacija
varilnega postopka - 5. del: (Elektro)uporovno varjenje (ISO 15609-5:2011)
Specification and qualification of welding procedures for metallic materials - Welding
procedure specification - Part 5: Resistance welding (ISO 15609-5:2011)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Schweißanweisung - Teil 5: Widerstandsschweißen (ISO 15609-5:2011)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Descriptif d'un mode opératoire de soudage - Partie 5: Soudage par
résistance (ISO 15609-5:2011)
Ta slovenski standard je istoveten z: EN ISO 15609-5:2011
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 15609-5:2011 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15609-5:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 15609-5:2011


EUROPEAN STANDARD
EN ISO 15609-5

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2011
ICS 25.160.10 Supersedes EN ISO 15609-5:2004
English Version
Specification and qualification of welding procedures for metallic
materials - Welding procedure specification - Part 5: Resistance
welding (ISO 15609-5:2011)
Descriptif et qualification d'un mode opératoire de soudage Anforderung und Qualifizierung von Schweißverfahren für
pour les matériaux métalliques - Descriptif d'un mode metallische Werkstoffe - Schweißanweisung - Teil 5:
opératoire de soudage - Partie 5: Soudage par résistance Widerstandsschweißen (ISO 15609-5:2011)
(ISO 15609-5:2011)
This European Standard was approved by CEN on 30 September 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15609-5:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15609-5:2011
EN ISO 15609-5:2011 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 15609-5:2011
EN ISO 15609-5:2011 (E)
Foreword
This document (EN ISO 15609-5:2011) has been prepared by Technical Committee ISO/TC 44 "Welding and
allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding”, the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the
latest by April 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15609-5:2004.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15609-5:2011 has been approved by CEN as a EN ISO 15609-5:2011 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 15609-5:2011

---------------------- Page: 6 ----------------------

SIST EN ISO 15609-5:2011

INTERNATIONAL ISO
STANDARD 15609-5
Second edition
2011-10-01

Specification and qualification of welding
procedures for metallic materials —
Welding procedure specification —
Part 5:
Resistance welding
Descriptif et qualification d'un mode opératoire de soudage pour les
matériaux métalliques — Descriptif et qualification d'un mode opératoire
de soudage —
Partie 5: Soudage par résistance




Reference number
ISO 15609-5:2011(E)
©
ISO 2011

---------------------- Page: 7 ----------------------

SIST EN ISO 15609-5:2011
ISO 15609-5:2011(E)

COPYRIGHT PROTECTED DOCUMENT


©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2011 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 15609-5:2011
ISO 15609-5:2011(E)
Contents Page
Foreword . iv
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 2
4  Technical contents of welding procedure specification . 2
4.1  General . 2
4.2  Product manufacturer . 2
4.3  Parent materials . 2
4.3.1  Composition . 2
4.3.2  Dimensions . 2
4.4  Common to all welding procedures . 2
4.4.1  Welding process . 2
4.4.2  Machine specification . 3
4.4.3  Joint design . 3
4.4.4  Surface and edge preparation . 3
4.4.5  Welding technique . 4
4.4.6  Resistance welding electrodes and auxiliaries . 4
4.4.7  Machine parameters and control settings . 4
Annex A (informative) Example of a WPS — I: Planned process requirements. 5
Annex B (informative) Example of a WPS — II: Quality acceptance criteria . 6
Annex C (informative) Example of a WPS — III: Welding machine set-up . 7
Annex D (informative) Examples of parameters in resistance welding . 8
Bibliography . 13

© ISO 2011 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 15609-5:2011
ISO 15609-5:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15609-5 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 6, Resistance welding and allied mechanical joining.
This second edition cancels and replaces the first edition (ISO 15609-5:2004), which has been technically
revised.
ISO 15609 consists of the following parts, under the general title Specification and qualification of welding
procedures for metallic materials — Welding procedure specification:
 Part 1: Arc welding
 Part 2: Gas welding
 Part 3: Electron beam welding
 Part 4: Laser beam welding
 Part 5: Resistance welding
 Part 6: Laser-arc hybrid welding
Requests for official interpretations of any aspect of this part of ISO 15609 should be directed to the
Secretariat of ISO/TC 44/SC 6 via your national standards body. A complete listing of these bodies can be
found at www.iso.org.
iv © ISO 2011 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 15609-5:2011
INTERNATIONAL STANDARD ISO 15609-5:2011(E)

Specification and qualification of welding procedures for
metallic materials — Welding procedure specification —
Part 5:
Resistance welding
1 Scope
This part of ISO 15609 specifies requirements for the content of welding procedure specifications for
resistance spot, seam, butt and projection welding processes. It is necessary to establish the acceptability of
applying the principles of this part of ISO 15609 to other resistance and related welding processes before any
qualification is undertaken.
NOTE Details of ISO 15609 (all parts — for titles, see Foreword) are given in ISO 15607:2003, Annex A.
Variables listed in this part of ISO 15609 are those influencing either weld dimensions (quality), weld nugget
dimension, weld pattern positioning, mechanical properties or geometry of the welded joint.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 669, Resistance welding — Resistance welding equipment — Mechanical and electrical requirements
ISO 4063, Welding and allied processes — Nomenclature of processes and reference numbers
ISO 5183 (all parts), Resistance welding equipment — Electrode adaptors, male taper 1:10
ISO 5184, Straight resistance spot welding electrodes
ISO 5821, Resistance welding — Spot welding electrode caps
ISO 5827, Spot we
...