SIST EN IEC 61084-2-3:2024
(Main)Cable trunking systems and cable ducting systems for electrical installations - Part 2-3: Particular requirements - Slotted cable trunking systems intended for installation in cabinets (IEC 61084-2-3:2017)
Cable trunking systems and cable ducting systems for electrical installations - Part 2-3: Particular requirements - Slotted cable trunking systems intended for installation in cabinets (IEC 61084-2-3:2017)
This part 2-3 of the EN IEC 61084 series specifies particular requirements and tests slotted cable
trunking systems intended for mounting inside cabinets in electrical and/or communication system installations.
Elektroinstallationskanalsysteme für elektrische Installationen - Teil 2-3: Besondere Anforderungen an Verdrahtungskanäle zum Einbau in Schaltschränke (IEC 61084-2-3:2017)
Systèmes de goulottes et systèmes de conduits-profilés pour installations électriques - Partie 2-3: Exigences particulières - Systèmes de goulottes de câblage pour installation dans les armoires (IEC 61084-2-3:2017)
L'IEC 61084-2-3:2017 spécifie les exigences et les essais pour les systèmes de goulottes (SG) et les systèmes de conduits-profilés (SCP) destinés au logement de conducteurs isolés, câbles et éventuels autres équipements électriques et, si nécessaire, à leur séparation de protection électrique, dans des installations électriques et/ou de systèmes de communication. La tension maximale de ces installations est de 1 000 V en courant alternatif et 1 500 V en courant continu.
Les systèmes de goulottes de câblage sont prévus pour être montés à l’intérieur d’armoires dans des installations électriques et/ou de systèmes de communication.
Le présent document ne s’applique pas aux systèmes de conduits, systèmes de chemins de câble, systèmes d’échelles à câble, systèmes de canalisations préfabriquées ou aux équipements couverts par d’autres normes.
Cette Norme internationale doit être utilisée conjointement avec l’IEC 61084-1:2017.
Sistemi kabelskih korit in sistemi kabelskih cevi za električne inštalacije - 2-3. del: Posebne zahteve - Utorski sistemi kabelskih korit za inštalacije v priključnih omaricah (IEC 61084-2-3:2017)
Ta 2-3. del skupine standardov EN IEC 61084 določa posebne zahteve in preskuse za utorske sisteme kabelskih korit, namenjene za montažo v priključne omarice v električnih inštalacijah in/ali inštalacijah komunikacijskih sistemov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2024
Sistemi kabelskih korit in sistemi kabelskih cevi za električne inštalacije - 2-3. del:
Posebne zahteve - Utorski sistemi kabelskih korit za inštalacije v priključnih
omaricah (IEC 61084-2-3:2017)
Cable trunking systems and cable ducting systems for electrical installations - Part 2-3:
Particular requirements - Slotted cable trunking systems intended for installation in
cabinets (IEC 61084-2-3:2017)
Elektroinstallationskanalsysteme für elektrische Installationen - Teil 2-3: Besondere
Anforderungen an Verdrahtungskanäle zum Einbau in Schaltschränke (IEC 61084-2-
3:2017)
Systèmes de goulottes et systèmes de conduits-profilés pour installations électriques -
Partie 2-3: Exigences particulières - Systèmes de goulottes de câblage pour installation
dans les armoires (IEC 61084-2-3:2017)
Ta slovenski standard je istoveten z: EN IEC 61084-2-3:2024
ICS:
29.120.10 Inštalacijske cevi za Conduits for electrical
električne namene purposes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61084-2-3
NORME EUROPÉENNE
EUROPÄISCHE NORM September 2024
ICS 29.060.01; 29.120.10 Supersedes EN 50085-2-3:2010
English Version
Cable trunking systems and cable ducting systems for electrical
installations - Part 2-3: Particular requirements - Slotted cable
trunking systems intended for installation in cabinets
(IEC 61084-2-3:2017)
Systèmes de goulottes et systèmes de conduits-profilés Installationskanalsysteme für elektrische Installationen - Teil
pour installations électriques - Partie 2-3: Exigences 2-3: Besondere Anforderungen - Verdrahtungskanäle zum
particulières - Systèmes de goulottes de câblage pour Einbau in Schaltschränke
installation dans les armoires (IEC 61084-2-3:2017)
(IEC 61084-2-3:2017)
This European Standard was approved by CENELEC on 2024-08-05. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61084-2-3:2024 E
European foreword
This document (EN IEC 61084-2-3:2024) consists of the text of document IEC 61084-2-3:2017,
prepared by SC 23A "Cable management systems" of IEC/TC 23 "Electrical accessories".
The following dates are fixed:
• latest date by which this document has to be (dop) 2025-08-05
implemented at national level by publication of an
identical national standard or by endorsement
• latest date by which the national standards (dow) 2029-08-05
conflicting with this document have to be withdrawn
This document supersedes EN 50085-2-3:2010 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CENELEC by the
European Commission. The Standing Committee of the EFTA States subsequently approves these
requests for its Member States.
For relationship with EU Legislation, see informative Annex ZZ, which is an integral part of
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61084-2-3:2017 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
ISO 2768-1:1989 NOTE Approved as EN 22768-1:1993 (not modified)
IEC 61084-2-3 ®
Edition 1.0 2017-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Cable trunking systems and cable ducting systems for electrical installations –
Part 2-3: Particular requirements – Slotted cable trunking systems intended for
installation in cabinets
Systèmes de goulottes et systèmes de conduits-profilés pour installations
électriques –
Partie 2-3: Exigences particulières – Systèmes de goulottes de câblage pour
installation dans les armoires
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.060.01; 29.120.10 ISBN 978-2-8322-4120-2
– 2 – IEC 61084-2-3:2017 IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 6
5 General conditions for tests . 6
6 Classification . 7
7 Marking and documentation . 7
8 Dimensions. 7
9 Construction . 8
10 Mechanical properties. 8
11 Electrical properties . 10
12 Thermal properties . 10
13 Fire hazard . 10
14 External influences . 11
15 Electromagnetic compatibility . 11
Annex A (informative) Types of cable trunking systems (CTS) and cable ducting
systems (CDS) . 17
Bibliography . 18
Figure 101 – Examples of pattern of fixing holes in the base of the slotted trunking
length . 12
Figure 102 – Examples of sizes for the fixing holes . 13
Figure 103 – Fixing distances for cable support test . 14
Figure 104 – Arrangements for cable support test . 15
Figure 105 – Arrangement for flame test . 16
IEC 61084-2-3:2017 IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CABLE TRUNKING SYSTEMS AND CABLE DUCTING
SYSTEMS FOR ELECTRICAL INSTALLATIONS –
Part 2-3: Particular requirements – Slotted cable
trunking systems intended for installation in cabinets
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61084-2-3 has been prepared by subcommittee 23A: Cable
management systems, of IEC technical committee 23: Electrical accessories.
This International standard is to be used in conjunction with IEC 61084-1:2017.
The text of this standard is based on the following documents:
FDIS Report on voting
23A/829/FDIS 23A/835/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
– 4 – IEC 61084-2-3:2017 IEC 2017
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
This Part of the IEC 61084 series supplements or modifies the corresponding clauses of
IEC 61084-1:2017 as follows:
– where no particular clause or subclause of IEC 61084-1 is mentioned, the corresponding
clause or subclause applies as far as it is reasonable;
– where "addition", "modification" or “replacement” is stated, the relevant text of
IEC 61084-11 is to be adapted accordingly;
– subclauses, figures and tables which are additional to those in IEC 61084-1 are numbered
starting from 101.
In this standard, the following print types are used:
– requirements and definitions: roman type;
– compliance statements: italic type.
A list of all parts in the IEC 61084 series, published under the general title Cable trunking and
cable ducting systems for electrical installations, can be found on the IEC
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.