SIST EN 62149-2:2014

Fibre optic active components and devices - Performance standards - Part 2: 850 nm discrete vertical cavity surface emitting laser devices

EN IEC 62149-2 covers the performance specification for 850-nm discrete vertical cavity surface emitting laser (VCSEL) devices of transverse multimode types used for fibre optic telecommunication and optical data transmission applications. The performance standard contains a definition of the product performance requirements together with a series of sets of tests and measurements with clearly defined conditions, severities, and pass/fail criteria. The tests are intended to be run on a “once-off” basis to prove any product’s ability to satisfy the performance standard’s requirements. A product that has been shown to meet all the requirements of a performance standard can be declared as complying with the performance standard, but should then be controlled by a quality assurance/quality conformance program. Depending on the modulation speeds, sub-categorized specifications are defined. Types A1, A2, A3 and A4 correspond to 1,25 Gbit/s, 2,5 Gbit/s, 4,25 Gbit/s and 10 Gbit/s VCSELs, respectively. Each sub-categorized specification is also defined by separate details depending on the device types, such as specifications for a VCSEL device without a monitor photodiode (case a) and for a VCSEL device with a monitor photodiode (case b).

Aktive Lichtwellenleiterbauelemente und geräte - Betriebsverhalten - Teil 2: Oberflächenemittierende 850-nm-Laserbauelemente mit vertikalem Resonator

Composants et dispositifs actifs à fibres optiques - Normes de performances - Partie 2: Dispositifs discrets à laser 850 nm à cavité verticale émettant en surface

L'IEC 62149-2:2014 concerne les spécifications de performance des dispositifs discrets à laser 850 nm émettant en surface (VCSEL) de types multimodaux transverses utilisés dans les applications de télécommunication à fibres optiques et les applications de transmission de données par moyen optique. La norme de performance contient une définition des exigences de performance de produit ainsi qu'une série de jeux d'essais et de mesures avec des conditions, sévérités et critères d'acceptation/de refus bien définis. Les essais sont destinés à être effectués un à un, pour prouver la capacité du produit à satisfaire aux exigences des normes de performance. Cette deuxième édition annule et remplace la première édition parue en 2009, dont elle constitue une révision technique. Les modifications techniques significatives par rapport à l'édition précédente consistent en l'introduction des normes de performance pour les dispositifs laser à cavité verticale émettant en surface (VCSEL) d'une longueur d'onde de 850 nm à 10 Gbit/s et la suppression des schémas de boîtiers et des configurations de broches dans l'Article A.4 et l'Article B.4 en citant en remplacement la norme de boîtier VCSEL, IEC 62148-15.
Mots clés: discrets à laser 850 nm émettant en surface (VCSEL), types multimodaux transverses

Aktivne komponente in naprave optičnih vlaken - Izvedbeni standardi - 2. del: Diskretni laserji s površinsko emisijo in navpičnim resonatorjem z valovno dolžino 850 nanometrov (IEC 62149-2:2014)

Standard EN IEC 62149-2 obravnava izvedbeno specifikacijo za diskretne laserje s površinsko emisijo in navpičnim resonatorjem (VCSEL) transverzalnih večrodnih tipov z valovno dolžino 850 nanometrov za uporabo na področju telekomunikacij z optičnimi vlakni in optičnega prenosa podatkov. Izvedbeni standard vsebuje opredelitev zahtev glede zmogljivosti za izdelek skupaj z naborom serij preskusov in meritev z jasno določenimi pogoji, stopnjami zahtevnosti in merili za uspešno/neuspešno opravljen preskus. Preskusi so namenjeni enkratnemu izvajanju, z njimi pa se dokaže, ali lahko izdelek izpolnjuje zahteve tehničnega standarda. Izdelek, ki dokazano izpolnjuje vse zahteve izvedbenega standarda, je mogoče šteti za skladen z izvedbenim standardom, vendar naj bi ga v tem primeru nadzoroval program za zagotavljanje skladnosti/skladnost s kakovostjo. Glede na modulacijske hitrosti so določene podkategorizirane specifikacije. Tipi A1, A2, A3 in A4 ustrezajo 1,25 Gbit/s, 2,5 Gbit/s, 4,25 Gbit/s in 10 Gbit/s VCSEL. Vsaka podkategorizirana specifikacija je opredeljena tudi z ločenimi podrobnostmi glede na tipe naprave, kot so specifikacije za napravo VCSEL brez nadzorne fotodiode (primer a) in za napravo VCSEL z nadzorno fotodiodo (primer b).

General Information

• Status: Published
• Publication Date: 08-Sep-2014
• ICS: 31.260 - Optoelectronics. Laser equipment
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Sep-2014
• Due Date: 10-Nov-2014
• Completion Date: 09-Sep-2014
• Ref Project: EN 62149-2:2014 - Fibre optic active components and devices - Performance standards - Part 2: 850 nm discrete vertical cavity surface emitting laser devices

Relations

• Replaces: SIST EN 62149-2:2009 - Fibre optic active components and devices - Performance standard - Part 2: 850 nm discrete vertical cavity surface emitting laser devices (IEC 62149-2:2009)
• Effective Date: 22-Jan-2013
• Replaces: SIST EN 62149-2:2009 - Fibre optic active components and devices - Performance standard - Part 2: 850 nm discrete vertical cavity surface emitting laser devices (IEC 62149-2:2009)
• Effective Date: 28-Jan-2023
• Revised: SIST EN 62149-2:2009 - Fibre optic active components and devices - Performance standard - Part 2: 850 nm discrete vertical cavity surface emitting laser devices (IEC 62149-2:2009)
• Effective Date: 06-May-2014
• Replaces: SIST EN 62149-2:2009 - Fibre optic active components and devices - Performance standard - Part 2: 850 nm discrete vertical cavity surface emitting laser devices (IEC 62149-2:2009)
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62149-2:2014
01-oktober-2014
1DGRPHãþD
SIST EN 62149-2:2009
$NWLYQHNRPSRQHQWHLQQDSUDYHRSWLþQLKYODNHQ,]YHGEHQLVWDQGDUGLGHO
'LVNUHWQLODVHUMLVSRYUãLQVNRHPLVLMRLQQDYSLþQLPUHVRQDWRUMHP]YDORYQRGROåLQR
QDQRPHWURY,(&
Fibre optic active components and devices - Performance standards - Part 2: 850 nm
discrete vertical cavity surface emitting laser devices
Ta slovenski standard je istoveten z: EN 62149-2:2014
ICS:
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 62149-2:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 62149-2:2014

---------------------- Page: 2 ----------------------

SIST EN 62149-2:2014


EUROPEAN STANDARD EN 62149-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
August 2014
ICS 33.180.20 Supersedes EN 62149-2:2009
English Version
Fibre optic active components and devices - Performance
standards - Part 2: 850 nm discrete vertical cavity surface
emitting laser devices
(IEC 62149-2:2014)
Composants et dispositifs actifs à fibres optiques - Normes Aktive Lichtwellenleiterbauelemente und geräte -
de performances - Partie 2: Dispositifs discrets à laser Betriebsverhalten - Teil 2: Oberflächenemittierende
850 nm à cavité verticale émettant en surface 850-nm-Laserbauelemente mit Vertikalresonator
(CEI 62149-2:2014) (IEC 62149-2:2014)
This European Standard was approved by CENELEC on 2014-06-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 62149-2:2014 E

---------------------- Page: 3 ----------------------

SIST EN 62149-2:2014
EN 62149-2:2014 - 2 -

Foreword
The text of document 86C/1146/CDV, future edition 2 of IEC 62149-2, prepared by SC 86C "Fibre
optic systems and active devices” of IEC/TC 86 “Fibre optics" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN 62149-2:2014.

The following dates are fixed:
• latest date by which the document has to be (dop) 2015-03-30
implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2017-06-30
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This document supersedes EN 62149-2:2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.

Endorsement notice
The text of the International Standard IEC 62149-2:2014 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60191 NOTE Harmonized in EN 60191 Series.
IEC 60747-5-1 NOTE Harmonized as EN 60747-5-1.
IEC 60749 NOTE Harmonized in EN 60749 Series.
IEC 60825 NOTE Harmonized in EN 60825 Series.
IEC 60874 NOTE Harmonized in EN 60874 Series.
IEC 61280-1-3 NOTE Harmonized as EN 61280-1-3.
IEC 62007-1 NOTE Harmonized as EN 62007-1.
IEC 62007-2 NOTE Harmonized as EN 62007-2.
IEC 62148-1 NOTE Harmonized as EN 62148-1.
IEC 62149-1 NOTE Harmonized as EN 62149-1.

---------------------- Page: 4 ----------------------

SIST EN 62149-2:2014
- 3 - EN 62149-2:2014
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.

Publication Year Title EN/HD Year
IEC 60749-6 -  Semiconductor devices - Mechanical and EN 60749-6 -
climatic test methods -
Part 6: Storage at high temperature
IEC 60749-7 -  Semiconductor devices - Mechanical and EN 60749-7 -
climatic test methods -
Part 7: Internal moisture content
measurement and the analysis of other
residual gases
IEC 60749-10 -  Semiconductor devices - Mechanical and EN 60749-10 -
climatic test methods -
Part 10: Mechanical shock
IEC 60749-11 -  Semiconductor devices - Mechanical and EN 60749-11 -
climatic test methods -
Part 11: Rapid change of temperature -
Two-fluid-bath method
IEC 60749-12 -  Semiconductor devices - Mechanical and EN 60749-12 -
climatic test methods -
Part 12: Vibration, variable frequency
IEC 60749-25 -  Semiconductor devices - Mechanical and EN 60749-25 -
climatic test methods -
Part 25: Temperature cycling
IEC 60749-26 -  Semiconductor devices - Mechanical and EN 60749-26 -
climatic test methods -
Part 26: Electrostatic discharge (ESD)
sensitivity testing - Human body model
(HBM)
IEC 60825-1 -  Safety of laser products - EN 60825-1 -
Part 1: Equipment classification and
requirements
IEC 60950-1 -  Information technology equipment - EN 60950-1 -
Safety -
Part 1: General requirements
IEC 61300-2-4 -  Fibre optic interconnecting devices and EN 61300-2-4 -
passive components - Basic test and
measurement procedures -
Part 2-4: Tests - Fibre/cable retention
IEC 61300-2-19 -  Fibre optic interconnecting devices and EN 61300-2-19 -
passive components - Basic test and
measurement procedures -
Part 2-19: Tests - Damp heat (steady
state)

---------------------- Page: 5 ----------------------

SIST EN 62149-2:2014
EN 62149-2:2014 - 4 -
Publication Year Title EN/HD Year
IEC 61300-2-48 -  Fibre optic interconnecting devices and EN 61300-2-48 -
passive components - Basic test and
measurement procedures -
Part 2-48: Tests - Temperature-humidity
cycling
IEC 62148-15 -  Fibre optic active components and EN 62148-15 -
devices - Package and interface
standards -
Part 15: Discrete vertical cavity surface
emitting laser packages
IEC Guide 107 -  Electromagnetic compatibility - Guide to - -
the drafting of electromagnetic
compatibility publications

---------------------- Page: 6 ----------------------

SIST EN 62149-2:2014



IEC 62149-2

®


Edition 2.0 2014-05




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Fibre optic active components and devices – Performance standards –

Part 2: 850 nm discrete vertical cavity surface emitting laser devices




Composants et dispositifs actifs à fibres optiques – Normes de performances –

Partie 2: Dispositifs discrets à laser 850 nm à cavité verticale émettant

en surface















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX R


ICS 33.180.20 ISBN 978-2-8322-1603-3



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 62149-2:2014
– 2 – IEC 62149-2:2014 © IEC 2014
CONTENTS

FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, symbols and abbreviations . 8
3.1 Terms and definitions . 8
3.2 Symbols and abbreviations . 9
4 Product parameters . 9
4.1 Absolute limiting ratings . 9
4.2 Operating environment . 10
4.3 Functional specification. 10
4.4 Diagrams . 10
5 Testing . 10
5.1 General . 10
5.2 Characterization testing . 10
5.3 Performance testing . 10
6 Environmental specifications . 10
6.1 General safety . 10
6.2 Laser safety . 10
6.3 Electromagnetic compatibility (EMC) requirements. 11
Annex A (normative) Specifications for multimode 850-nm VCSEL device without a
monitor photodiode (Case a) . 12
A.1 Absolute limiting ratings . 12
A.2 Operating environment . 12
A.3 Functional specification. 12
A.4 Diagrams . 13
A.5 Testing . 13
A.5.1 Characterization testing . 13
A.5.2 Performance testing. 13
Annex B (normative) Specifications for multimode 850 nm VCSEL device with a
monitor photodiode (Case b) . 16
B.1 Absolute limiting ratings . 16
B.2 Operating environment . 16
B.3 Functional specification. 16
B.4 Diagrams . 17
B.5 Testing . 17
B.5.1 Characterization testing . 17
B.5.2 Performance testing. 18
Bibliography . 20

Table 1 – Operating environment . 10
Table A.1 – Absolute limiting ratings . 12
Table A.2 – Operating conditions for functional specification . 12
Table A.3 – Functional specification . 13
Table A.4 – Performance test plan . 14

---------------------- Page: 8 ----------------------

SIST EN 62149-2:2014
IEC 62149-2:2014 © IEC 2014 – 3 –
Table A.5 – Recommended performance test failure criteria . 15
Table B.1 – Absolute limiting ratings . 16
Table B.2 – Operating conditions for functional specification . 16
Table B.3 – Functional specification . 17
Table B.4 – Performance test plan . 18
Table B.5 – Recommended performance test failure criteria . 19

---------------------- Page: 9 ----------------------

SIST EN 62149-2:2014
– 4 – IEC 62149-2:2014 © IEC 2014
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
PERFORMANCE STANDARDS –

Part 2: 850 nm discrete vertical cavity surface emitting laser devices

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62149-2 has been prepared by subcommittee 86C: Fibre optic
systems and active devices, of IEC technical committee 86: Fibre optics.
This second edition cancels and replaces the first edition published in 2009 and constitutes a
technical revision.
The significant technical changes with respect to the previous edition include the introduction
of the performance standards for 10 Gbit/s 850-nm wavelength, vertical cavity surface
emitting laser (VCSEL) devices and the deletion of the package diagrams and pin
configurations in Clause A.4 and Clause B.4 by citing the VCSEL package standard
IEC 62148-15 instead.

---------------------- Page: 10 ----------------------

SIST EN 62149-2:2014
IEC 62149-2:2014 © IEC 2014 – 5 –
The text of this standard is based on the following documents:
CDV Report on voting
86C/1146/CDV 86C/1229/RVC

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 62149 series, published under the general title Fibre optic active
components and devices – Performance standards, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------

SIST EN 62149-2:2014
– 6 – IEC 62149-2:2014 © IEC 2014
INTRODUCTION
Fibre optic laser devices are used to convert electrical signals into optical signals. This part of
IEC 62149 covers the performance specification for 850 nm discrete vertical cavity surface
emitting laser devices in fibre optic telecommunication and optical data transmission
applications.

---------------------- Page: 12 ----------------------

SIST EN 62149-2:2014
IEC 62149-2:2014 © IEC 2014 – 7 –
FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
PERFORMANCE STANDARDS –

Part 2: 850 nm discrete vertical cavity surface emitting laser devices



1 Scope
This part of IEC 62149 covers the performance specification for 850-nm discrete vertical
cavity surface emitting laser (VCSEL) devices of transverse multimode types used for fibre
optic telecommunication and optical data transmission applications. The performance
standard contains a definition of the product performance requirements together with a series
of sets of tests and measurements with clearly defined conditions, severities, and pass/fail
criteria. The tests are intended to be run on a “once-off” basis to prove any product’s ability to
satisfy the performance standard’s requirements.
A product that has been shown to meet all the requirements of a performance standard can
be declared as complying with the performance standard, but should then be controlled by a
quality assurance/quality conformance program.
Depending
...