SIST EN 14409-1:2005
(Main)Plastics piping systems for renovation of underground water supply networks - Part 1: General
Plastics piping systems for renovation of underground water supply networks - Part 1: General
This document specifies the requirements and test methods for plastics piping systems used for renovation of underground water supply networks which transport water intended for human consumption, including raw water intake pipelines. It is applicable to pipes and fittings as manufactured as well as to the installed lining system; it does not cover sprayed coatings, the existing pipeline or any annular filler. This part of EN 14409 deals with the general requirements common to all relevant renovation techniques as defined in 3.2.
Kunststoff-Rohrleitungssysteme für die Renovierung erdverlegter Wasserversorgungsnetze - Teil 1: Allgemeines
Dieses Dokument legt die Anforderungen an und Prüfverfahren für Kunststoff-Rohrleitungssysteme fest, die für die
Renovierung von erdverlegten Wasserversorgungsnetzen für Trinkwasserzwecke verwendet werden, einschließlich
Rohwasser-Entnahmeleitungen. Sie gilt sowohl für vorgefertigte Rohre und Formstücke als auch für das
eingebaute Lining-System; sie legt weder Anforderungen an Spritzbeschichtungen noch an bestehende
Rohrleitungen oder gegebenenfalls erforderliche Ringraumfüllstoffe fest.
Dieser Teil von EN 14409 enthält die allgemeinen Anforderungen, die für alle Gruppen von Renovierungsverfahren
(Technikfamilien) nach 3.2 gelten.
Systemes de canalisations plastiques pour la rénovation des réseaux enterrés pour l'alimentation en eau - Partie 1 : Généralités
Le présent document spécifie les exigences et les méthodes d'essai pour les systemes de canalisations
utilisés pour la rénovation des réseaux enterrés pour l?alimentation transportant de l?eau destinée a la
consommation humaine, y compris les canalisations pour prise d?eau brute. Elle est applicable aux tubes et
raccords préfabriqués ou au systeme de rénovation une fois installé. Elle ne couvre pas les enduits projetés,
la canalisation existante ou le matériau de remplissage annulaire.
La présente partie de l?EN 14409 traite des exigences générales communes a toutes les techniques de
rénovation pertinentes, telles que définies en 3.2.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z vodo - 1. del: Splošno
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z vodo - 1. del: SplošnoKunststoff-Rohrleitungssysteme für die Renovierung erdverlegter Wasserversorgungsnetze - Teil 1: AllgemeinesSystemes de canalisations plastiques pour la rénovation des réseaux enterrés pour l'alimentation en eau - Partie 1 : GénéralitésPlastics piping systems for renovation of underground water supply networks - Part 1: General93.025Zunanji sistemi za prevajanje vodeExternal water conveyance systems23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:EN 14409-1:2004SIST EN 14409-1:2005en,fr,de01-januar-2005SIST EN 14409-1:2005SLOVENSKI
STANDARD
SIST EN 14409-1:2005
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14409-1September 2004ICS 23.040.01; 93.025 English versionPlastics piping systems for renovation of underground watersupply networks - Part 1: GeneralSystèmes de canalisations plastiques pour la rénovationdes réseaux enterrés pour l'alimentation en eau - Partie 1 :GénéralitésKunststoff-Rohrleitungssysteme für die Renovierungerdverlegter Wasserversorgungsnetze - Teil 1: AllgemeinesThis European Standard was approved by CEN on 29 July 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14409-1:2004: ESIST EN 14409-1:2005
EN 14409-1:2004 (E) 2 Contents page Contents.2 Foreword.3 Introduction.5 1 Scope.6 2 Normative references.6 3 Terms, definitions, symbols and abbreviations.6 4 Pipes at the "M" stage.13 5 Fittings at the "M" stage.14 6 Valves.15 7 Fitness for purpose of the system for pipes and fittings at the “I” stage.15 8 Installation practice.16 Annex A (informative)
Recommended scheme for assessment of conformity.20 Bibliography.23
SIST EN 14409-1:2005
EN 14409-1:2004 (E) 3 Foreword
This document (EN 14409-1:2004) has been prepared by Technical Committee CEN/TC 155 "Plastics piping systems and ducting systems", the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2005, and conflicting national standards shall be withdrawn at the latest by March 2005. This document is a part of a System Standard for plastics piping systems of various materials used for renovation of existing pipelines in a specified application area. System Standards for renovation dealing with the following applications are either available or in preparation: — Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks; — Plastics piping systems for renovation of underground water supply networks (this application); — Plastics piping systems for renovation of underground gas supply networks; — Plastics piping systems for renovation of underground drainage and sewerage networks under pressure; — Plastics piping systems for renovation of industrial pipelines. These System Standards are distinguished from those for conventionally installed plastics piping systems by setting requirements for certain characteristics in the as-installed condition, after site processing.
This is in addition to specifying requirements for system components as manufactured.
Each of the System Standards comprises a: —
Part 1: General
and all applicable renovation technique family related parts from the following list:
—
Part 21): Lining with continuous pipes —
Part 3: Lining with close-fit pipes —
Part 41): Lining with cured-in-place pipes —
Part 61): Lining with inserted hoses A consistent structure of clause headings has been adopted for all parts to facilitate direct comparisons across renovation technique families. Figure 1 shows the common part and clause structure and the relationship between EN 14409 and the System Standards for other application areas. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard : Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
1) At the date of publication of this standard, the standardization work on prEN 14409-2 and prEN 14409-4 and prEN 14409-6 has not started.
SIST EN 14409-1:2005
EN 14409-1:2004 (E) 4
Figure 1 Format of the renovation system standards SIST EN 14409-1:2005
EN 14409-1:2004 (E) 5 Introduction The requirements for any given renovation technique family are covered by Part 1: General, applied in conjunction with the relevant other part.
For example, for the requirements relating to Lining with continuous pipes it is necessary to refer to both parts 1 and 2.
Complementary information is contained in ISO/TR 11295 [5] and a supporting standard, EN 13689 [1], listed in the bibliography. Not all technique families are applicable to every area of application, and this is reflected in the part numbers actually included in each System Standard.
For the present document, the parts 1, 21), 3, 4 1), and 6 1) of EN 14409 apply. Recommended schemes for assessment of conformity of the plastics piping system with all relevant requirements are provided by way of informative annexes to each part. Attention is also drawn to EN 805 which has been taken into account during the preparation of this document.
1) At the date of publication of this standard, the standardization work on prEN 14409-2 and prEN 14409-4 and prEN 14409-6 has not started. SIST EN 14409-1:2005
EN 14409-1:2004 (E) 6 1 Scope This document specifies the requirements and test methods for plastics piping systems used for renovation of underground water supply networks which transport water intended for human consumption, including raw water intake pipelines.
It is applicable to pipes and fittings as manufactured as well as to the installed lining system; it does not cover sprayed coatings, the existing pipeline or any annular filler. This part of EN 14409 deals with the general requirements common to all relevant renovation techniques as defined in 3.2. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals — Material requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanised rubber EN 805, Water supply — Requirements for systems and components outside buildings prEN 14409-2 1), Plastics piping systems for renovation of underground water supply networks — Part 2:
Lining with continuous pipes (Start of standardization work expected) EN 14409-3, Plastics piping systems for renovation of underground water supply networks — Part 3:
Lining with close-fit pipes prEN 14409-4 1), Plastics piping systems for renovation of underground water supply networks — Part 4:
Lining with cured-in-place pipes (Standardization work not started) prEN 14409-6 1),Plastics piping systems for renovation of underground water supply networks — Part 6:
Lining with inserted hoses (Standardization work not started) EN ISO 472:2001, Plastics - Vocabulary (ISO 472:1999) EN ISO 1043-1:2001, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001). 3 Terms, definitions, symbols and abbreviations For the purposes of this document, the terms, definitions, symbols and abbreviations given in EN ISO 472:2001 and EN ISO 1043-1:2001 and the following apply. 3.1 General Terms and definitions 3.1.1 pipeline system interconnecting pipe network for the conveyance of fluids 3.1.2 rehabilitation all measures for restoring or upgrading the performance of an existing pipeline system
1) At the date of publication of this standard, the standardization work on prEN 14409-2 and prEN 14409-4 and prEN 14409-6 has not started. SIST EN 14409-1:2005
EN 14409-1:2004 (E) 7 3.1.3 renovation work incorporating all or part of the original fabric of the pipeline by means of which its current performance is improved 3.1.4 replacement rehabilitation of an existing pipeline system by the installation of a new pipeline system, without incorporating the original fabric 3.1.5 maintenance keeping an existing pipeline system operational without the installation of additional fabric 3.1.6 repair rectification of local damage 3.1.7 lining pipe pipe to be inserted for renovation purposes
3.1.8 liner lining pipe after installation 3.1.9 lining system lining pipe and all relevant fittings for insertion into an existing pipeline for the purposes of
renovation
3.1.10 renovated pipeline system the existing pipeline system plus the installed lining system used to renovate it, plus any grout or other annular filling material used 3.1.11 characteristic property, dimension or other feature of a material or component 3.1.12 declared value limiting value of a characteristic declared in advance by lining system supplier which becomes the requirement for the purposes of assessment of conformity 3.1.13 annular filler material for grouting annular space between existing pipeline and lining system 3.1.14 grouting process of filling voids around the lining system 3.1.15 "M" stage stage as manufactured, before any subsequent site processing of components associated with the particular renovation technique 3.1.16 "I" stage stage as installed, i.e. in final configuration after any site processing of components associated with the particular renovation technique SIST EN 14409-1:2005
EN 14409-1:2004 (E) 8 3.1.17 simulated installation installation of a lining system into a simulated host pipeline, using representative equipment and processes, to provide samples for testing which are representative of an actual installation 3.1.18 simulated host pipeline section of pipeline, which is not part of an operational network, but which replicates the environment of an operational network 3.1.19 technique family group of renovation techniques which are considered to have common characteristics for standardisation purposes
3.1.20 independent pressure pipe liner liner which is capable on its own of resisting without failure all applicable internal loads throughout its design life 3.1.21 interactive pressure pipe liner liner which relies on the host pipe for some measure of radial support in order to resist without failure all applicable internal loads throughout its design life 3.2
Terms and definitions related to techniques The various techniques for renovation of underground water supply networks, within the scope of pipeline rehabilitation techniques generally, are shown schematically in Figure 2. NOTE
For definitions of renovation techniques shown in Figure 2 but outside the scope of this document see EN 13689 [1]. SIST EN 14409-1:2005
EN 14409-1:2004 (E) 9
Figure 2 Technique families for renovation of underground water supply networks using plastics pipes, within the scope of pipeline rehabilitation techniques The technique families within the scope of this document are defined as follows: 3.2.1 lining with continuous pipes lining with pipe made continuous for the length of the section to be renovated prior to insertion, and which has not been shaped to give it a cross-sectional diameter smaller than its final diameter after installation 3.2.2 lining with close-fit pipes lining with a continuous pipe for which the cross-section is reduced to facilitate installation and reverted after installation to provide a close fit to the existing pipe NOTE
For the reduction in cross-section there are two options as follows: a)
reduction in the pipe manufacturing plant; the pipe is usually supplied coiled on a reel from which it is directly inserted; b)
reduction on site; the pipe is usually fed through the reduction equipment and simultaneously inserted in one continuous string. SIST EN 14409-1:2005
EN 14409-1:2004 (E) 10 3.2.3 lining with cured-in-place pipes lining with a flexible tube impregnated with a thermosetting resin which produces a pipe after resin cure 3.2.4 lining with inserted hoses lining with a reinforced hose, which is either permanently reverted to provide a pipe after installation, or inflates when water is transported under pressure 3.3
Geometrical definitions 3.3.1 nominal size numerical designation of the size of a component, which is a convenient round number approximately equal to the manufacturing dimension in millimetres 3.3.2 nominal size DN/OD nominal size, related to the outside diameter 3.3.3 nominal outside diameter dn specified outside diameter, in millimetres, assigned to a nominal size DN/OD NOTE
The nominal outside diameter expressed in millimetres is the minimum mean outside diameter dem,min defined in 3.3.5. 3.3.4 mean outside diameter dem value of the measurement of the outer circumference of a pipe or spigot end of a fitting in any cross-section, divided by π (≈ 3,142), and rounded to the next greater 0,1 mm 3.3.5 minimum mean outside diameter dem,min minimum value of the mean outside diameter as specified for a given nominal size 3.3.6 wall thickness e value of the measurement of the wall thickness at any point around the circumference of a component 3.3.7 mean wall thickness em arithmetic mean of a number of measurements of the wall thickness regularly spaced around the circumference and in the same cross-section of a component
3.3.8 nominal wall thickness en numerical designation to the wall thickness, which is a convenient round number, approximately equal to the manufacturing dimension in millimetres NOTE For thermoplastics solid-wall components the value of nominal wall thickness, en, is identical to the specified minimum wall thickness at any point, emin. 3.3.9 standard dimension ratio (SDR) ratio of the nominal outside diameter, dn, and the minimum wall thickness, emin SIST EN 14409-1:2005
EN 14409-1:2004 (E) 11 3.3.10 internal pressure resistance
capability to withstand internal hydrostatic pressurisation 3.4
Material definitions 3.4.1 virgin material material in a form such as granules, powder or liquid that has not been subjected to use or processing other than that required for its manufacture, and to which no reprocessable or recyclable material has been added 3.4.2 own reprocessable material material prepared from rejected unused pipes and fittings, including trimmings from the production of pipes and fittings, that will be reprocessed in a manufacturer’s plant after having being previously processed by the same manufacturer by a process such as moulding or extrusion, and for which the complete formulation is known 3.4.3 external reprocessable material material from rejected unused products or trimmings that will be reprocessed and that were originally processed by another manufacturer
NOTE
If a manufacturer has a production of products other than pipes and fittings, reprocessable material from that production is considered as external reprocessable material when used for pipes or fittings production. 3.4.4 recyclable material material prepared from used products which have been cleaned and crushed or ground
3.5
Definitions related to material characteristics No general definitions apply. 3.6
Definitions related to service conditions No general definitions apply. 3.7 Definitions related to joints No general definitions apply. 3.8
Definitions related to assessment of conformity 3.8.1 certification body impartial body, governmental or non-governmental, possessing the necessary competence and responsibility to carry out certification of conformity according to given rules of procedure and management 3.8.2 quality system organisational structure, responsibilities, procedures processes and resources for implementing quality management
3.8.3 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.8.4 type testing testing performed to prove that the material, component, joint or assembly is capable of conforming to the requirements given in the applicable standard SIST EN 14409-1:2005
EN 14409-1:2004 (E) 12 3.8.5 preliminary type testing type testing carried out by or on behalf of the manufacturer 3.8.6 initial type testing type testing carried out by or on behalf of a certification body for certification purposes 3.8.7 batch release test test performed by the manufacturer on a batch of components, which has to be satisfactorily completed before the batch can be released 3.8.8 process verification test test performed by the manufacturer on materials, components, joints or assemblies at specific intervals to confirm that the process continues to be capable of producing components conforming to the requirements given in the applicable standard(s) NOTE
Within this document, process verification testing is used to demonstrate that installation has been conducted as required.
3.8.9 audit test test performed by or on behalf of a certification body to confirm that the material, component, joint or assembly continues to conform to the requirements given in the relevant standard and to provide information to assess the effectiveness of the quality system 3.8.10 indirect test test performed by the manufacturer different from that specified for a particular characteristic, having verified its correlation with the specified test 3.8.11 witness testing testing accepted by a certification body for initial type testing and/or audit testing, which is carried out by, or on behalf of, the manufacturer and supervised by a representative of the certification body, qualified in testing 3.8.12 batch clearly identifiable collection of units or product quantity, manufactured consecutively or continuously under the same conditions, using materials conforming to the same specification 3.8.13 group collection of similar components from which samples are selected for testing purposes 3.8.14 assembly test piece consisting of various components 3.9
Symbols and abbreviations 3.9.1 Symbols dem :
mean outside diameter dem,min :
minimum mean outside diameter dn :
nominal outside diameter e :
wall thickness SIST EN 14409-1:2005
EN 14409-1:2004 (E) 13 em :
mean wall thickness emin. :
minimum wall thickness en :
nominal wall thickness 3.10
Abbreviations AT :
audit test BRT :
batch release test DN/OD :
nominal size, related to the outside diameter IT :
indirect
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.