SIST EN 10248-2:2024
(Main)Hot rolled steel sheet piles - Part 2: Tolerances on dimensions and shape
Hot rolled steel sheet piles - Part 2: Tolerances on dimensions and shape
This document specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot rolled steel sheet piles and is designed to be read in conjunction with EN 10248-1.
The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this document are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking bars.
This document also specifies options that can be agreed between the purchaser and the manufacturer at the time of the order and enquiry.
Warmgewalzte Spundbohlen aus Stahl - Teil 2: Grenzabmaße und Formtoleranzen
Dieses Dokument legt die Grenzabmaße sowie die Rechtwinkligkeit der Enden, die Geradheit und die Masse von warmgewalzten Spundbohlen fest und ist zusammen mit der EN 10248-1 zu verwenden.
Die Erzeugnisse sind für allgemeine, strukturelle Anwendungen und für das Bauwesen verwendbar. Die Arten von Spundbohlen in diesem Dokument sind: Z-Profil, U-Profil, Flachprofil, H-Profil mit ihren Verbindungsschlössern.
Dieses Dokument legt auch Optionen fest, die zwischen dem Hersteller und dem Besteller bei der Anfrage und Bestellung vereinbart werden können.
Palplanches en acier laminées à chaud - Partie 2 : Tolérances sur dimensions et forme
Le présent document spécifie les tolérances relatives aux dimensions, à l'équerrage des extrémités, à la rectitude et à la masse des palplanches en acier laminées à chaud et est conçu pour être lu conjointement avec l’EN 10248-1.
Les produits désignés sont destinés à être utilisés dans la réalisation d'ouvrages divers, d'ouvrages de génie civil et d'éléments de construction. Les types de palplanches en acier couverts dans le présent document sont : les palplanches en Z, en U, plates, en H avec leurs serrures.
Le présent document spécifie également les options qui peuvent être convenues entre l'acheteur et le fabricant au moment de la commande et de l’appel d’offres.
Vroče valjane jeklene zagatnice - 2. del: Mejni odstopki mer in tolerance oblik
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 10248-2:2023
01-april-2023
Vroče valjana jeklena obešala - 2. del: Mejni odstopki mer in tolerance oblik
Hot rolled steel sheet piles - Part 2: Tolerances on dimensions and shape
Warmgewalzte Spundbohlen aus Stahl - Teil 2: Grenzabmaße und Formtoleranzen
Palplanches en acier laminées à chaud - Partie 2 : Tolérances sur dimensions et forme
Ta slovenski standard je istoveten z: prEN 10248-2
ICS:
77.140.70 Jekleni profili Steel profiles
oSIST prEN 10248-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN 10248-2:2023
oSIST prEN 10248-2:2023
DRAFT
EUROPEAN STANDARD
prEN 10248-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2023
ICS 77.140.70 Will supersede EN 10248-2:1995
English Version
Hot rolled steel sheet piles - Part 2: Tolerances on
dimensions and shape
Palplanches en acier laminées à chaud - Partie 2 : Warmgewalzte Spundbohlen aus Stahl - Teil 2:
Tolérances sur dimensions et forme Grenzabmaße und Formtoleranzen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 3.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10248-2:2023 E
worldwide for CEN national Members.
oSIST prEN 10248-2:2023
prEN 10248-2:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 General requirements . 4
5 Height of profiles . 5
5.1 U-shaped sheet piles . 5
5.2 Z-shaped sheet piles. 5
5.3 H-shaped sheet piles . 6
6 Width of profiles . 7
6.1 U-shaped sheet piles . 7
6.2 Z-shaped sheet piles. 8
6.3 Straight web sheet piles . 9
6.4 H-shaped sheet piles . 9
7 Wall thicknesses of profiles . 10
7.1 U-shaped sheet piles . 10
7.2 Z-shaped sheet piles. 10
7.3 Straight web sheet piles . 11
7.4 H-shaped sheet piles . 12
8 Straightness of profiles (deviation from straight line) . 13
9 Length of profiles . 14
10 Squareness of ends of profiles . 14
11 Mass of profiles . 16
12 Interlocks of profiles . 16
13 Options . 17
oSIST prEN 10248-2:2023
prEN 10248-2:2023 (E)
European foreword
This document (prEN 10248-2:2023) has been prepared by Technical Committee CEN/TC 459/SC 3
“Structural steels other than reinforcements”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10248-2:1995.
In comparison with the previous edition EN 10248-2:1995, the following technical modifications have
been made:
a) restructure of the standard;
b) update of the normative references and general requirements;
c) review of the sketches;
d) new wording for Clause 10;
e) new wording for Clause11 about the mass tolerance;
f) insertion of a new Table 15 about the misalignment of the head of sheet piles.
EN 10248 consists of the following parts under the general title Hot rolled steel sheet piles:
— Part 1: Technical delivery conditions
— Part 2: Tolerances on dimensions and shape
oSIST prEN 10248-2:2023
prEN 10248-2:2023 (E)
1 Scope
This document specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot
rolled steel sheet piles and is designed to be read in conjunction with EN 10248-1.
The products specified are for general, structural and civil engineering works. The types of steel sheet
piles covered by this document are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking
bars.
This document also specifies options that can be agreed between the purchaser and the manufacturer at
the time of the order and enquiry.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10021:2006, General technical delivery conditions for steel products
EN 10079:2007, Definition of steel products
EN 10248-1, Hot rolled steel sheet piles — Part 1: Technical delivery conditions
EN 12063, Execution of special geotechnical work — Sheet pile walls
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 10021:2006, EN 10079:2007
apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/ui
— IEC Electropedia: available at https://www.electropedia.org/
4 General requirements
The tolerances on dimensions and shape of this document shall apply, as far as possible, in addition to
the technical delivery conditions of EN 10248-1.
The determination of sheet pile dimensions and tolerances shall comply with the following preparation
before any measurement is carried out. This requirement shall apply in the workshop or on-site
without any distinction.
The sheet piles to be measured shall be extracted from the storing stack and laid down on the ground
separately. The reference ground shall be flat and free of any local relief over the length o
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.