SIST EN 12390-4:2019
(Main)Testing hardened concrete - Part 4: Compressive strength - Specification for testing machines
Testing hardened concrete - Part 4: Compressive strength - Specification for testing machines
This document specifies the requirements for the performance of compression testing machines for the measurement of the compressive strength of concrete.
Prüfung von Festbeton - Teil 4: Bestimmung der Druckfestigkeit - Anforderungen an Prüfmaschinen
Dieses Dokument enthält Festlegungen der Anforderungen an Druckprüfmaschinen zur Prüfung der Druckfestigkeit von Beton.
Essais pour béton durci - Partie 4 : Résistance à la compression - Caractéristiques des machines d'essai
Le présent document spécifie les exigences relatives aux performances des machines d’essai pour le mesurage de la résistance du béton à la compression.
Preskušanje strjenega betona - 4. del: Tlačna trdnost - Specifikacija za stiskalnice
Ta dokument določa zahteve za zmogljivost tlačnih stiskalnic za merjenje tlačne trdnosti betona.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12390-4:2019
01-december-2019
Nadomešča:
SIST EN 12390-4:2001
Preskušanje strjenega betona - 4. del: Tlačna trdnost - Specifikacija za stiskalnice
Testing hardened concrete - Part 4: Compressive strength - Specification for testing
machines
Prüfung von Festbeton - Teil 4: Bestimmung der Druckfestigkeit - Anforderungen an
Prüfmaschinen
Essais pour béton durci - Partie 4 : Résistance à la compression - Caractéristiques des
machines d'essai
Ta slovenski standard je istoveten z: EN 12390-4:2019
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
SIST EN 12390-4:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12390-4:2019
---------------------- Page: 2 ----------------------
SIST EN 12390-4:2019
EN 12390-4
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 91.100.30 Supersedes EN 12390-4:2000
English Version
Testing hardened concrete - Part 4: Compressive strength -
Specification for testing machines
Essais pour béton durci - Partie 4 : Résistance à la Prüfung von Festbeton - Teil 4: Bestimmung der
compression - Caractéristiques des machines d'essai Druckfestigkeit - Anforderungen an Prüfmaschinen
This European Standard was approved by CEN on 19 August 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12390-4:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12390-4:2019
EN 12390-4:2019 (E)
Contents Page
European foreword . 3
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Construction of machines . 7
5 Details to be provided by the supplier/manufacturer . 10
Annex A (normative) Strain gauged column and proving procedure for compression testing
machines . 12
Bibliography . 16
2
---------------------- Page: 4 ----------------------
SIST EN 12390-4:2019
EN 12390-4:2019 (E)
European foreword
This document (EN 12390-4:2019) has been prepared by Technical Committee CEN/TC 104 “Concrete
and related products”, the secretariat of which is held by SN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be
withdra
...
SLOVENSKI STANDARD
oSIST prEN 12390-4:2018
01-junij-2018
3UHVNXãDQMHVWUMHQHJDEHWRQDGHO7ODþQDWUGQRVW6SHFLILNDFLMD]DVWLVNDOQLFH
Testing hardened concrete - Part 4: Compressive strength - Specification for testing
machines
Prüfung von Festbeton - Teil 4: Bestimmung der Druckfestigkeit - Anforderungen an
Prüfmaschinen
Essais pour béton durci - Partie 4 : Résistance à la compression - Caractéristiques des
machines d'essai
Ta slovenski standard je istoveten z: prEN 12390-4
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
oSIST prEN 12390-4:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 12390-4:2018
---------------------- Page: 2 ----------------------
oSIST prEN 12390-4:2018
DRAFT
EUROPEAN STANDARD
prEN 12390-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2018
ICS 91.100.30 Will supersede EN 12390-4:2000
English Version
Testing hardened concrete - Part 4: Compressive strength -
Specification for testing machines
Essais pour béton durci - Partie 4 : Résistance à la Prüfung von Festbeton - Teil 4: Bestimmung der
compression - Caractéristiques des machines d'essai Druckfestigkeit - Anforderungen an Prüfmaschinen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 104.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12390-4:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 12390-4:2018
prEN 12390-4:2018 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Construction of machines . 6
4.1 Machine platens, auxiliary platens and spacing blocks . 6
4.2 Force measurement . 7
4.2.1 Force indicator . 7
4.2.2 Force indicator accuracy . 7
4.3 Force control .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.