SIST EN IEC 60317-25:2020

Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 (IEC 60317-25:2020)

This part of IEC 60317 specifies the requirements of enamelled round aluminium winding
wires of class 200 with a dual coating. The underlying coating is based on polyester or
polyesterimide resin, which can be modified provided it retains the chemical identity of the
original resin and meets all specified wire requirements. The superimposed coating is based
on polyamide-imide resin.
NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to
enhance certain performance or application characteristics.
The range of nominal conductor diameters covered by this document is:
– Grade 1: 0,250 mm up to and including 3,150 mm;
– Grade 2: 0,250 mm up to and including 5,000 mm.
The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3:2008 and
IEC 60317-0-3:2008/AMD1:2013.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 25: Runddrähte aus Aluminium, lackisoliert mit Polyester oder Polyesterimid und darüber mit Polyamidimid, Klasse 200 (IEC 60317-25:2020)

Spécifications pour types particuliers de fils de bobinage - Partie 25: Fil de section circulaire en aluminium émaillé avec polyester ou polyesterimide et avec surcouche polyamide-imide, classe 200 (IEC 60317-25:2020)

IEC 60317-25:2020 est disponible sous forme de IEC 60317-25:2020 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.

L'IEC 60317-25:2020 spécifie les exigences relatives aux fils de bobinage de section circulaire en aluminium émaillés de classe 200 à double revêtement. La sous-couche de revêtement est à base de résine polyester ou polyesterimide qui peut être modifiée sous réserve qu'elle conserve les propriétés chimiques de la résine initiale et respecte l'ensemble des exigences spécifiées du fil. La surcouche de revêtement est un matériau à base de résine polyamide-imide.
NOTE Une résine modifiée est une résine dont les propriétés chimiques ont été modifiées ou qui contient un ou plusieurs additifs visant à améliorer certaines performances ou caractéristiques d'application.
La gamme des diamètres nominaux des conducteurs couverts par le présent document est:
- Grade 1: 0,250 mm jusques et y compris 3,150 mm;
- Grade 2: 0,250 mm jusques et y compris 5,000 mm.
Les diamètres nominaux des conducteurs sont spécifiés à l'Article 4 de l'IEC 60317-0-3:2008 et de l'IEC 60317-0-3:2008/AMD1:2013. Cette quatrième édition annule et remplace la troisième édition parue en 2010. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- ajout d'un nouveau 3.2.2 contenant des notes générales sur le fil de bobinage intégrées auparavant au domaine d'application);
- révision de l'Article 11 afin de tenir compte des conducteurs de diamètre nominal intermédiaire;
- révision de l'Article 7 pour indiquer que l'essai concernant l'effet de ressort n'est pas applicable;
- révision de l'Article 16 afin de spécifier uniquement le pourcentage de matière extractible et la tension de claquage diélectrique minimale retenue.

Specifikacije za posebne vrste navijalnih žic - 25. del: S poliamidimidom emajlirana, s poliestrom ali poliesterimidom prekrita aluminijasta okrogla žica, razred 200 (IEC 60317-25:2020)

General Information

• Status: Published
• Publication Date: 03-Sep-2020
• ICS: 29.060.10 - Wires
• ICS: 77.150.10 - Aluminium products
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 12-Aug-2020
• Due Date: 17-Oct-2020
• Completion Date: 04-Sep-2020
• Ref Project: EN IEC 60317-25:2020 - Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200

Relations

• Revised: SIST EN 60317-25:2010 - Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 (IEC 60317-25:2010)
• Effective Date: 17-Sep-2018
• Replaces: SIST EN 60317-25:2010 - Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 (IEC 60317-25:2010)
• Effective Date: 03-Aug-2020

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60317-25:2020
01-november-2020
Nadomešča:
SIST EN 60317-25:2010
Specifikacije za posebne vrste navijalnih žic - 25. del: S poliamidimidom
emajlirana, s poliestrom ali poliesterimidom prekrita aluminijasta okrogla žica,
razred 200 (IEC 60317-25:2020)
Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide
overcoated with polyamide-imide enamelled round aluminium wire, class 200 (IEC 60317
-25:2020)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 25:
Runddrähte aus Aluminium, lackisoliert mit Polyester oder Polyesterimid und darüber mit
Polyamidimid, Klasse 200 (IEC 60317-25:2020)
Spécifications pour types particuliers de fils de bobinage - Partie 25: Fil de section
circulaire en aluminium émaillé avec polyester ou polyesterimide et avec surcouche
polyamide-imide, classe 200 (IEC 60317-25:2020)
Ta slovenski standard je istoveten z: EN IEC 60317-25:2020
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
SIST EN IEC 60317-25:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60317-25:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 60317-25:2020


EUROPEAN STANDARD EN IEC 60317-25

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2020
ICS 29.060.10 Supersedes EN 60317-25:2010 and all of its
amendments and corrigenda (if any)
English Version
Specifications for particular types of winding wires - Part 25:
Polyester or polyesterimide overcoated with polyamide-imide
enamelled round aluminium wire, class 200
(IEC 60317-25:2020)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 25: Fil de section circulaire en aluminium émaillé Wickeldrähten - Teil 25: Runddrähte aus Aluminium,
revêtu de polyester ou de polyesterimide avec du lackisoliert mit Polyester oder Polyesterimid und darüber mit
polyamide-imide, de classe 200 Polyamidimid, Klasse 200
(IEC 60317-25:2020) (IEC 60317-25:2020)
This European Standard was approved by CENELEC on 2020-07-14. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60317-25:2020 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60317-25:2020
EN IEC 60317-25:2020 (E)
European foreword
The text of document 55/1840/FDIS, future edition 4 of IEC 60317-25, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60317-25:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-04-14
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-07-14
document have to be withdrawn

This document supersedes EN 60317-25:2010 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60317-25:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60317 (series) NOTE Harmonized as EN 60317 (series)
IEC 60851 (series) NOTE Harmonized as EN 60851 (series)


2

---------------------- Page: 4 ----------------------
SIST EN IEC 60317-25:2020
EN IEC 60317-25:2020 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60317-0-3 2008 Specifications for particular types of EN 60317-0-3 2008
winding wires - Part 0-3: General
requirements - Enamelled round aluminium
wire
+ A1 2013  + A1 2013
+ A2 2019  + A2 2019

3

---------------------- Page: 5 ----------------------
SIST EN IEC 60317-25:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 60317-25:2020



IEC 60317-25

®


Edition 4.0 2020-06




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Specifications for particular types of winding wires –

Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled

round aluminium wire, class 200



Spécifications pour types particuliers de fils de bobinage –

Partie 25: Fil de section circulaire en aluminium émaillé revêtu de polyester ou


de polyesterimide avec du polyamide-imide, de classe 200













INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 29.060.10 ISBN 978-2-8322-8395-0




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 60317-25:2020
– 2 – IEC 60317-25:2020 © IEC 2020
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, general notes and appearance . 6
3.1 Terms and definitions . 6
3.2 General notes . 7
3.2.1 Methods of test . 7
3.2.2 Winding wire . 7
3.3 Appearance . 7
4 Dimensions. 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
9 Heat shock . 7
10 Cut-through . 7
11 Resistance to abrasion (nominal conductor diameters up to and including
2,500 mm) . 8
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 9
17 Solderability . 9
18 Heat or solvent bonding . 9
19 Dielectric dissipation factor . 9
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin hole test . 9
30 Packaging . 9
Bibliography . 10

Table 1 – Resistance to abrasion . 8

---------------------- Page: 8 ----------------------
SIST EN IEC 60317-25:2020
IEC 60317-25:2020 © IEC 2020 – 3 –
INTERNATIONAL E
...