SIST EN ISO 4829-1:2018

Steel and cast iron - Determination of total silicon contents - Reduced molybdosilicate spectrophotometric method - Part 1: Silicon contents between 0,05 % and 1,0 % (ISO 4829-1:2018)

This document specifies a spectrophotometric method for the determination of total silicon in steel and
cast iron using reduced molybdosilicate.
The method is applicable to the determination of silicon mass fraction between 0,05 % and 1,0 %.

Stahl- und Gusseisen - Bestimmung des Gesamtsiliciumanteils - Spektrophotometrische Methode mit reduziertem Molybdatosilicat - Teil 1: Siliciumanteile zwischen 0,05 % und 1,0 % (ISO 4829-1:2018)

Dieses Dokument legt ein spektralphotometrisches Verfahren mit reduziertem Molybdatosilicat zur Bestimmung des Gesamtsiliciumanteils in Stahl und Gusseisen fest.
Dieses Verfahren lässt sich auf Siliciumanteile im Bereich von 0,05 % bis 1,0 % (Massenanteil) anwenden.

Aciers et fontes - Détermination du silicium total - Méthode spectrophotométrique au silicomolybdate réduit - Partie 1: Teneurs en silicium comprises entre 0,05 % et 1,0 % (ISO 4829-1:2018)

L'ISO 4829-1:2018 spécifie une méthode spectrophotométrique au silicomolybdate réduit pour la détermination du silicium dans les aciers et les fontes.
La méthode est applicable aux teneurs en silicium comprises entre 0,05 % et 1,0 %.

Jeklo in lito železo - Določevanje celotnega silicija - Spektrofotometrična metoda z reduciranim molibdo-silikatom - 1. del: Deleži silicija med 0,05 % in 1 % (ISO 4829-1:2018)

Ta dokument določa spektrofotometrično metodo za določevanje celotnega silicija v jeklu in
železovi zlitini z reduciranim molibdo-silikatom.
Metoda se uporablja za določevanje masnega deleža silicija med 0,05 % in 1,0 %.

General Information

• Status: Published
• Public Enquiry End Date: 20-Feb-2017
• Publication Date: 14-May-2018
• ICS: 77.040.30 - Chemical analysis of metals
• ICS: 77.080.01 - Ferrous metals in general
• Technical Committee: IFEK - Ferrous metals
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 11-May-2018
• Due Date: 16-Jul-2018
• Completion Date: 15-May-2018
• Ref Project: EN ISO 4829-1:2018 - Steel and cast iron - Determination of total silicon contents - Reduced molybdosilicate spectrophotometric method - Part 1: Silicon contents between 0,05 % and 1,0 % (ISO 4829-1:2018)

Relations

• Revised: SIST EN 24829-1:1997 - Steel and cast iron - Determination of total silicon content - Reduced molybdosilicate spectrophotometric method - Part 1: Silicon content between 0,05 and 1% (ISO 4829-1:1986)
• Effective Date: 10-Dec-2014
• Replaces: SIST EN 24829-1:1997/AC:1997 - Steel and cast iron - Determination of total silicon content - Reduced molybdosilicate spectrophotometric method - Part 1: Silicon content between 0,05 and 1% (ISO 4829-1:1986)
• Effective Date: 09-May-2018
• Replaces: SIST EN 24829-1:1997 - Steel and cast iron - Determination of total silicon content - Reduced molybdosilicate spectrophotometric method - Part 1: Silicon content between 0,05 and 1% (ISO 4829-1:1986)
• Effective Date: 09-May-2018

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 4829-1:2018
01-julij-2018
1DGRPHãþD
SIST EN 24829-1:1997
SIST EN 24829-1:1997/AC:1997
-HNORLQOLWRåHOH]R'RORþHYDQMHFHORWQHJDVLOLFLMD6SHNWURIRWRPHWULþQDPHWRGD]
UHGXFLUDQLPPROLEGRVLOLNDWRPGHO'HOHåLVLOLFLMDPHGLQ,62

Steel and cast iron - Determination of total silicon contents - Reduced molybdosilicate
spectrophotometric method - Part 1: Silicon contents between 0,05 % and 1,0 % (ISO
4829-1:2018)
Stahl- und Gusseisen - Bestimmung des Gesamtsiliciumanteils - Spektrophotometrische
Methode mit reduziertem Molybdatosilicat - Teil 1: Siliciumanteile zwischen 0,05 % und
1,0 % (ISO 4829-1:2018)
Aciers et fontes - Détermination du silicium total - Méthode spectrophotométrique au
silicomolybdate réduit - Partie 1: Teneurs en silicium comprises entre 0,05 % et 1,0 %
(ISO 4829-1:2018)
Ta slovenski standard je istoveten z: EN ISO 4829-1:2018
ICS:
77.040.30 Kemijska analiza kovin Chemical analysis of metals
77.080.01 Železne kovine na splošno Ferrous metals in general
SIST EN ISO 4829-1:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 4829-1:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 4829-1:2018


EN ISO 4829-1
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2018
EUROPÄISCHE NORM
ICS 77.080.01 Supersedes EN 24829-1:1990
English Version

Steel and cast iron - Determination of total silicon contents
- Reduced molybdosilicate spectrophotometric method -
Part 1: Silicon contents between 0,05 % and 1,0 % (ISO
4829-1:2018)
Aciers et fontes - Détermination du silicium total - Stahl- und Gusseisen - Bestimmung des
Méthode spectrophotométrique au silicomolybdate Gesamtsiliciumanteils - Spektrophotometrische
réduit - Partie 1: Teneurs en silicium comprises entre Methode mit reduziertem Molybdatosilicat - Teil 1:
0,05 % et 1,0 % (ISO 4829-1:2018) Siliciumanteile zwischen 0,05 % und 1,0 % (ISO 4829-
1:2018)
This European Standard was approved by CEN on 6 March 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4829-1:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 4829-1:2018
EN ISO 4829-1:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 4829-1:2018
EN ISO 4829-1:2018 (E)
European foreword
This document (EN ISO 4829-1:2018) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 102 “Methods of chemical analysis for iron and steel”
the secretariat of which is held by SIS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2018, and conflicting national standards
shall be withdrawn at the latest by November 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 24829-1:1990.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4829-1:2018 has been approved by CEN as EN ISO 4829-1:2018 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 4829-1:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 4829-1:2018
INTERNATIONAL ISO
STANDARD 4829-1
Second edition
2018-03
Steel and cast iron — Determination
of total silicon contents — Reduced
molybdosilicate spectrophotometric
method —
Part 1:
Silicon contents between 0,05 % and
1,0 %
Aciers et fontes — Détermination du silicium total — Méthode
spectrophotométrique au silicomolybdate réduit —
Partie 1: Teneurs en silicium comprises entre 0,05 % et 1,0 %
Reference number
ISO 4829-1:2018(E)
©
ISO 2018

---------------------- Page: 7 ----------------------

SIST EN ISO 4829-1:2018
ISO 4829-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 4829-1:2018
ISO 4829-1:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Reagents . 2
6 Apparatus . 3
7 Sampling . 4
8 Procedure. 4
8.1 Test portion . 4
8.2 Blank test . 4
8.3 Determination . 4
8.3.1 Dissolution of the test portion . 4
8.3.2 Treatment of insoluble residue . 5
8.3.3 Preparation of the test solution . 5
8.3.4 Development of the colour . 5
8.3.5 Spectrophotometric measurements . 6
8.4 Establishment of the calibration curve . 6
8.4.1 Preparation of the calibration solutions . 6
8.4.2 Spectrophotometric measurements . 6
8.4.3 Plotting of the calibration curves . 6
9 Expression of results . 7
9.1 Method of calculation . 7
9.2 Precision . 8
10 Test report . 8
Annex A (informative) Additional information on the international interlaboratory test.9
Annex B (informative) Graphical representation of precision data .10
Bibliography .11
© ISO 2018 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 4829-1:2018
ISO 4829-1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 1, Methods of
determination of chemical composition.
This second edition cancels and replaces the first edition (ISO 4829-1:1986), which has been technically
revised.
A list of all the parts in the ISO 4829 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 4829-1:2018
INTERNATIONAL STANDARD ISO 4829-1:2018(E)
Steel and cast iron — Determination of total silicon
contents — Reduced molybdosilicate spectrophotometric
method —
Part 1:
Silicon contents between 0,05 % and 1,0 %
1 Scope
This document specifies a spectrophotometric method for the determination of total silicon in steel and
cast iron using reduced molybdosilicate.
The method is applicable to the determination of silicon mass fraction between 0,05 % and 1,0 %.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 648, Laboratory glassware — Single-volume pipettes
ISO 1042, Laboratory glassware — One-mark volumetric flasks
ISO 3696, Water for analytical laboratory use — Specification and test methods
ISO 14284, Steel and iron — Sampling and preparation of samples for the determination of chemical
composition
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at https:// www .iso .org/ obp
4 Principle
Dissolution of a test portion in an acid mixture appropriate to the alloy composition.
Fusion of the acid-insoluble residue with sodium peroxide. Formation of the oxidized molybdosilicate
(yellow) complex in weak acid solution.
Selective reduction of the molybdosilicate complex to a blue complex with ascorbic acid, after increasing
the sulphuric acid concentration and adding oxalic acid to prevent the interference of phosphorus,
arsenic and vanadium.
Spectrophotometric measurement of the reduced blue complex at a wavelength of about 810 nm.
© ISO 2018 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 4829-1:2018
ISO 4829-1:2018(E)

5 Reagents
During the analysis, unless otherwise specified, use only reagents of recognized analytical grade and
only grade 2 water as specified in ISO 3696. Water demineralized by ion-exchange shall not be used as
it may contain significant amounts of colloidal silica.
Reagents supplied in glass bottles, once opened, can absorb moisture and become reactive to glassware.
Alkaline reagents, e.g. sodium carbonate and sodium peroxide, are particularly susceptible.
To avoid the risk of significant contamination arising from this source, it is recommended that only
freshly opened bottles of all reagents be used for the preparation of reagent solutions.
To avoid adventitious contamination, the water shall be prepared, as required, for the specific purpose
and collected in polypropylen
...