SIST EN 13617-4:2005
(Main)Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
This document specifies safety requirements for the construction and performance of swivels to be fitted to delivery hose assemblies on metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l×min-1. It pays particular attention to electrical, mechanical and hydraulic characteristics of swivels.
This document applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This document also addresses electrical and mechanical hazards of swivels.
This document is not applicable to swivels for the dispensing of any compressed gas.
.
Tankstellen - Teil 4: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von Drehgelenken für Zapfsäulen und druckversorgte Zapfsäulen
Stations-service - Partie 4 : Exigences de sécurité relatives a la construction et aux performances des raccords tournants utilisés sur les distributeurs de carburants
Le présent document spécifie les exigences de sécurité relatives a la construction et aux performances des raccords tournants destinés a etre montés sur les flexibles des ensembles de mesurage et de distribution installés dans les stations-service et utilisés pour distribuer des carburants liquides dans des réservoirs de véhicules a moteur, de bateaux, d'avions légers et dans des réservoirs portables, a des débits n'excédant pas 200 l×min-1. Il accorde une attention particuliere aux caractéristiques électriques, mécaniques et hydrauliques des raccords tournants.
Le présent document traite principalement des phénomenes dangereux liés a l'inflammation des carburants liquides distribués ou de leur vapeur. Le présent document s'intéresse également aux dangers électriques et mécaniques des raccords tournants.
Le présent document ne s'applique pas aux raccords tournants destinés a la distribution de gaz comprimés.
Bencinske črpalke - 4. del: Varnostne zahteve za izdelavo in lastnosti vrtljivih delov na avtomatih za točenje goriva in razdeljevalnikih
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Tankstellen - Teil 4: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von Drehgelenken für Zapfsäulen und druckversorgte ZapfsäulenStations-service - Partie 4 : Exigences de sécurité relatives a la construction et aux performances des raccords tournants utilisés sur les distributeurs de carburantsPetrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 13617-4:2004SIST EN 13617-4:2005en01-januar-2005SIST EN 13617-4:2005SLOVENSKI
STANDARD
SIST EN 13617-4:2005
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13617-4
October 2004 ICS 75.200
English version
Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
Stations-service - Partie 4 : Exigences de sécurité relatives à la construction et aux performances des raccords tournants utilisés sur les distributeurs de carburants
Tankstellen - Teil 4: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise von Drehgelenken für Zapfsäulen und druckversorgte Zapfsäulen This European Standard was approved by CEN on 16 August 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13617-4:2004: ESIST EN 13617-4:2005
EN 13617-4:2004 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.5 4 Explosion protection measures.5 5 Construction.5 5.1 General.5 5.2 Connection threads.5 5.3 Safe breaks.6 6 Physical properties.6 7 Functional requirements.7 8 Frequency of testing.7 9 Information for use.8 9.1 General.8 9.2 Marking and instruction.8 Annex A (normative)
Testing.9 Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or other provisions of EU Directives.11
SIST EN 13617-4:2005
EN 13617-4:2004 (E) 3 Foreword This document (EN 13617-4:2004) has been prepared by Technical Committee CEN/TC 221 “Shop fabricated metallic tanks and equipment for storage tanks and for service stations”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by April 2005. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. SIST EN 13617-4:2005
EN 13617-4:2004 (E) 4 1 Scope This document specifies safety requirements for the construction and performance of swivels to be fitted to delivery hose assemblies on metering pumps and dispensers installed at filling stations and used to dispense liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l⋅min-1. It pays particular attention to electrical, mechanical and hydraulic characteristics of swivels. This document applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This document also addresses electrical and mechanical hazards of swivels. This document is not applicable to swivels for the dispensing of any compressed gas. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 228, Automotive fuels – Unleaded petrol – Requirements and test methods EN 1127–1, Explosive atmospheres — Explosion prevention and protection — Part 1: Basic concepts and methodology EN 1360, Rubber hoses and hose assemblies for measured fuels dispensing — Specification EN 13012:2001, Petrol filling stations —Construction and performance of automatic nozzles for use on fuel dispensers EN 13463-1:2001, Non-electrical equipment for potentially explosive atmospheres — Part 1: Basic method and requirements prEN 13483, Hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems — Specification EN 13617–1:2004, Petrol filling stations — Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units EN 13617–2:2004, Petrol filling stations — Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers EN 50014:1997, Electrical apparatus for potentially explosive atmospheres — General requirements EN 60079-0, Electrical apparatus for explosive gas atmospheres – Part 0: General requirements EN ISO 8031:1997, Rubber and plastics hoses and hose assemblies — Determination of electrical resistance (ISO 8031:1993) EN ISO 228–1, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) ISO 261, ISO general-purpose metric screw threads — General plan ISO 965–2, ISO general-purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality ISO 11925–3, Reaction to fire tests — Ignitability of building products subjected to direct impingement of flame — Part 3: Multi-source test SIST EN 13617-4:2005
EN 13617-4:2004 (E) 5 3 Terms and definitions For the purposes of this document, the terms and definitions according to EN 13012:2001, EN 13617–1:2004 and EN 13617–2:2004 and the following apply: 3.1 swivel a device fitted between nozzle and metering pump or dispenser to allow rotational movement 3.2 single plane swivel a swivel with one plane of rotation 3.3 dual plane swivel a swivel with two planes of rotation 4 Explosion protection measures 4.1 Explosion protection measures shall be taken in accordance with EN 1127-1 and Annex B of EN 13617-1:2004. 4.2 Equipment and components used within hazardous areas shall be suitable as a minimum requirement for Explosion Group IIA and temperature class T3 as defined in EN 60079-0 and EN 13463–1.
Inside the vapour path the requirements for equipment group II, Category 1 as defined in EN 13463-1 shall apply. 5 Construction 5.1 General All electrical and non-electrical equipment and components, intended for use in potentially explosive atmospheres, shall be designed and constructed according to good engineering practice and in conformity with the required categories for group II equipment to ensure avoidance of any ignition source. To classify the Category of the equipment it shall be subjected to an ignition hazard assessment in accordance with 5.2 of EN 13463-1:2001. Materials used in the construction shall be chemically and dimensionally stable under known service conditions. Materials likely to come into contact with fuels in both liquid and vapour phases shall be resistant to attack by these fuels. Conformity shall be demonstrated by manufacturers' declaration and by the tests detailed in Annex A. Light alloys when used shall conform to the requirements of Clause 8 of EN 13463–1:2001. If other specifications for explosion protected equipment impose more stringent requirements then the more stringent requirement shall apply.
All components shall be of corrosion resistant material or shall be provided with a corrosion resistant protective coating.
Outside surfaces likely to be handled shall be free of sharp edges. If protective covers are fitted they shall be constructed such that they allow ventilation and evaporation of fuel even if some shrinkage occurs. They shall not affect the performance of the swivels. The sealing surfaces of the connection threads shall be designed such that they are suitable for use with an enclosed O-ring or flat gasket. 5.2 Connection threads Connection threads shall be one of the following styles: SIST EN 13617-4:2005
EN 13617-4:2004 (E) 6 Style 1: Swivels without a vapour recovery path, shall use parallel threads in accordance with EN ISO 228–1. The connection thread dimensions shall be in accordance with Table 1 Table 1 — Thread specifications Nominal connect
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.