SIST EN 6033:2016

Aerospace series - Carbon fibre reinforced plastics - Test method - Determination of interlaminar fracture toughness energy - Mode I - GIC

This standard specifies the procedure to determine the mode I interlaminar fracture toughness energy GIC of carbon fibre composites manufactured from unidirectional tape or woven fabric.
This standard does not give any directions necessary to meet health and safety requirements. It is the responsibility of the user of this standard to consult and establish appropriate health and safety precautions.

Luft- und Raumfahrt - Kohlenstoffaserverstärkte Kunststoffe - Prüfverfahren - Bestimmung der interlaminaren Energiefreisetzungsrate - Mode I - GIC

Diese Norm legt das Verfahren zur Bestimmung der interlaminaren Energiefreisetzungsrate GIC, Mode I, von kohlenstofffaserverstärkten Kunststoffen fest, die aus gleichgerichtetem Band oder Gewebe hergestellt wurden.
Diese Norm legt keine Anleitung fest, die für das Einhalten der Gesundheits  und Sicherheitsvorschriften erforderlich ist. Es liegt in der Verantwortung des Anwenders dieser Norm, die entsprechenden Gesundheits- und Sicherheitsvorkehrungen zu treffen.

Série aérospatiale - Matières plastiques renforcées de fibres de carbone - Méthode d'essai - Détermination de l'énergie de ténacité en rupture interlaminaire - Mode I - GIC

La présente norme spécifie la procédure pour la détermination de l’énergie de ténacité en rupture interlaminaire, mode I, GIC, des composites de fibres de carbone fabriqués à base de bandes ou de fibres textiles unidirectionnelles.
La présente norme ne fournit pas d'indication nécessaire pour satisfaire les exigences d'hygiène et de sécurité. Il est de la responsabilité de l’utilisateur de la présente norme de consulter et de mettre en place les précautions d'hygiène et de sécurité appropriées.

Aeronavtika - Z ogljikovimi vlakni ojačeni polimerni materiali - Preskusna metoda - Ugotavljanje energije pri medplastni lomni žilavosti - Način I - GIC

Ta standard določa postopek za ugotavljanje energije GIC pri medplastni lomni žilavosti v okviru načina I za kompozite iz ogljikovih vlaken, izdelane iz enosmernega traku ali z vlakni ojačenega materiala.
Ta standard ne vsebuje nobenih smernic, potrebnih za izpolnjevanje zdravstvenih in varnostnih zahtev. Uporabnik tega standarda se mora posvetovati in določiti ustrezne zdravstvene in varnostne ukrepe.

General Information

• Status: Published
• Publication Date: 03-Jan-2016
• ICS: 49.025.40 - Rubber and plastics
• ICS: 83.120 - Reinforced plastics
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 08-Dec-2015
• Due Date: 12-Feb-2016
• Completion Date: 04-Jan-2016
• Ref Project: EN 6033:2015 - Aerospace series - Carbon fibre reinforced plastics - Test method - Determination of interlaminar fracture toughness energy - Mode I - GIC

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 6033:2016
01-februar-2016
$HURQDYWLND=RJOMLNRYLPLYODNQLRMDþHQLSROLPHUQLPDWHULDOL3UHVNXVQDPHWRGD
8JRWDYOMDQMHHQHUJLMHSULPHGSODVWQLORPQLåLODYRVWL1DþLQ,*,&
Aerospace series - Carbon fibre reinforced plastics - Test method - Determination of
interlaminar fracture toughness energy - Mode I - GIC
Luft- und Raumfahrt - Kohlenstoffaserverstärkte Kunststoffe - Prüfverfahren -
Bestimmung der interlaminaren Energiefreisetzungsrate - Mode I - GIC
Série aérospatiale - Matières plastiques renforcées de fibres de carbone - Méthode
d'essai - Détermination de l'énergie de ténacité en rupture interlaminaire - Mode I - GIC
Ta slovenski standard je istoveten z: EN 6033:2015
ICS:
49.025.40 Guma in polimerni materiali Rubber and plastics
83.120 2MDþDQLSROLPHUL Reinforced plastics
SIST EN 6033:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 6033:2016

---------------------- Page: 2 ----------------------

SIST EN 6033:2016


EN 6033
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2015
EUROPÄISCHE NORM
ICS 49.025.40
English Version

Aerospace series - Carbon fibre reinforced plastics - Test
method - Determination of interlaminar fracture
toughness energy - Mode I - GIC
Série aérospatiale - Matières plastiques renforcées de Luft- und Raumfahrt - Kohlenstoffaserverstärkte
fibres de carbone - Méthode d'essai - Détermination de Kunststoffe - Prüfverfahren - Bestimmung der
l'énergie de ténacité en rupture interlaminaire - Mode I interlaminaren Energiefreisetzungsrate - Mode I - GIC
- GIC
This European Standard was approved by CEN on 10 August 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6033:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 6033:2016
EN 6033:2015 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle of the method . 4
5 Designation of the method . 5
6 Apparatus . 5
7 Test specimen . 5
8 Procedure. 6
9 Presentation of the results . 7
10 Test report . 7
2

---------------------- Page: 4 ----------------------

SIST EN 6033:2016
EN 6033:2015 (E)
European foreword
This document (EN 6033:2015) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be
withdrawn at the latest by May 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 6033:2016
EN 6033:2015 (E)
1 Scope
This standard specifies the procedure to determine the mode I interlaminar fracture toughness energy
G of carbon fibre composites manufactured from unidirectional tape or woven fabric.
IC
This standard does not give any directions necessary to meet health and safety requirements. It is the
responsibility of the user of this standard to consult and establish appropriate health and safety
precautions.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
1)
EN 2565, Aerospace series — Preparation of carbon fibre reinforced resin panels for test purposes
EN 2743, Aerospace series — Fibre reinforced plastics — Standard procedures for conditioning prior to
testing unaged materials
EN 6034, Aerospace series — Carbon fibre reinforced plastics — Test method — Determination of
1)
interlaminar fracture toughness energ
...