SIST EN 6034:2016

Aerospace series - Carbon fibre reinforced plastics - Test method - Determination of interlaminar fracture toughness energy - Mode II - GIIC

This standard specifies the procedure to determine the mode II interlaminar fracture toughness energy GIIC of carbon fibre composites manufactured from unidirectional tape or woven fabric.
This standard does not give any directions necessary to meet health and safety requirements. It is the responsibility of the user of this standard to consult and establish appropriate health and safety precautions.

Luft- und Raumfahrt - Kohlenstofffaserverstärkte Kunststoffe - Prüfverfahren - Bestimmung der interlaminaren Energiefreisetzungsrate - Mode II - GIIC

Diese Norm legt das Verfahren fest zur Bestimmung der interlaminaren Energiefreisetzungsrate GIIC, Mode II, von kohlenstofffaserverstärkten Kunststoffen, die aus gleichgerichtetem Band oder Gewebe hergestellt wurden.
Diese Norm legt keine Anleitung fest, die für das Einhalten der Gesundheits  und Sicherheitsvorschriften erforderlich ist. Es liegt in der Verantwortung des Anwenders dieser Norm, die entsprechenden Gesundheits- und Sicherheitsvorkehrungen zu treffen.

Série aérospatiale - Matières plastiques renforcées de fibres de carbone - Méthode d'essai - Détermination de l'énergie de ténacité en rupture interlaminaire - Mode II - GIIC

Aeronavtika - Z ogljikovimi vlakni ojačeni polimerni materiali - Preskusna metoda - Ugotavljanje energije pri medplastni lomni žilavosti - Način II - GIIC

Ta standard določa postopek za ugotavljanje energije GIIC pri medplastni lomni žilavosti v okviru načina II za kompozite iz ogljikovih vlaken, izdelane iz enosmernega traku ali z vlakni ojačenega materiala.
Ta standard ne vsebuje nobenih smernic, potrebnih za izpolnjevanje zdravstvenih in varnostnih zahtev. Uporabnik tega standarda se mora posvetovati in določiti ustrezne zdravstvene in varnostne ukrepe.

General Information

• Status: Published
• Publication Date: 03-Jan-2016
• ICS: 49.025.40 - Rubber and plastics
• ICS: 83.120 - Reinforced plastics
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 08-Dec-2015
• Due Date: 12-Feb-2016
• Completion Date: 04-Jan-2016
• Ref Project: EN 6034:2015 - Aerospace series - Carbon fibre reinforced plastics - Test method - Determination of interlaminar fracture toughness energy - Mode II - GIIC

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 6034:2016
01-februar-2016
$HURQDYWLND=RJOMLNRYLPLYODNQLRMDþHQLSROLPHUQLPDWHULDOL3UHVNXVQDPHWRGD
8JRWDYOMDQMHHQHUJLMHSULPHGSODVWQLORPQLåLODYRVWL1DþLQ,,*,,&
Aerospace series - Carbon fibre reinforced plastics - Test method - Determination of
interlaminar fracture toughness energy - Mode II - GIIC
Luft- und Raumfahrt - Kohlenstofffaserverstärkte Kunststoffe - Prüfverfahren -
Bestimmung der interlaminaren Energiefreisetzungsrate - Mode II - GIIC
Série aérospatiale - Matières plastiques renforcées de fibres de carbone - Méthode
d'essai - Détermination de l'énergie de ténacité en rupture interlaminaire - Mode II - GIIC
Ta slovenski standard je istoveten z: EN 6034:2015
ICS:
49.025.40 Guma in polimerni materiali Rubber and plastics
83.120 2MDþDQLSROLPHUL Reinforced plastics
SIST EN 6034:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 6034:2016

---------------------- Page: 2 ----------------------

SIST EN 6034:2016


EN 6034
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2015
EUROPÄISCHE NORM
ICS 49.025.40
English Version

Aerospace series - Carbon fibre reinforced plastics - Test
method - Determination of interlaminar fracture
toughness energy - Mode II - GIIC
Série aérospatiale - Matières plastiques renforcées de Luft- und Raumfahrt - Kohlenstofffaserverstärkte
fibres de carbone - Méthode d'essai - Détermination de Kunststoffe - Prüfverfahren - Bestimmung der
l'énergie de ténacité en rupture interlaminaire - Mode interlaminaren Energiefreisetzungsrate - Mode II - GIIC
II - GIIC
This European Standard was approved by CEN on 10 August 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6034:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 6034:2016
EN 6034:2015 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle of the method . 5
5 Designation of the method . 5
6 Apparatus . 5
7 Test specimen . 5
8 Procedure. 6
9 Presentation of the results . 8
10 Test report . 8

2

---------------------- Page: 4 ----------------------

SIST EN 6034:2016
EN 6034:2015 (E)
European foreword
This document (EN 6034:2015) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2016, and conflicting national standards shall be
withdrawn at the latest by May 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 6034:2016
EN 6034:2015 (E)
1 Scope
This standard specifies the procedure to determine the mode II interlaminar fracture toughness energy
G of carbon fibre composites manufactured from unidirectional tape or woven fabric.
IIC
This standard does not give any directions necessary to meet health and safety requirements. It is the
responsibility of the user of this standard to consult and establish appropriate health and safety
precautions.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
1)
EN 2565, Aerospace series — Preparation of carbon fibre reinforced resin panels for test purposes
EN 2743, Aerospace series — Fibre reinforced plastics — Standard procedures for conditioning prior to
testing unaged materials
EN 2823, Aerospace series — Fibre reinforced plastics — Test method for the determination of the effect of
1)
exposure to humid atmosphere on physical and mechanical characteristics
EN 6033, Aerospace series — Carbon fibre reinforced plastics — Test method — Determination of
1)
interlaminar fracture toughness energy — Mode I — G
IC
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
interlaminar fracture toughness energy
the interlaminar fracture toughness energy is the energy per unit plate width which is necessary to
produce an unit crack growth at an interlaminar crack between two plies of a laminate
3.2
mode II
the mode indicates the method by which the load is applied to produce the crack. Mode Il crack extends
as a result of shear forces at the crack tip introduced by a flexural test
3.3
G
IIC
G is the designation of the interlaminar fracture toughness energy determined by a mode II
...