SIST EN 60384-19:2016
(Main)Fixed capacitors for use in electronic equipment - Part 19: Sectional specification - Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors
Fixed capacitors for use in electronic equipment - Part 19: Sectional specification - Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors
This part of IEC 60384 is applicable to fixed surface mount capacitors for direct current, with
metallized electrodes and polyethylene-terephthalate dielectric for use in electronic
equipment. These capacitors have metallized connecting pads or soldering strips and are
intended to be mounted directly onto substrates for hybrid circuits or onto printed boards.
These capacitors may have "self-healing properties" depending on conditions of use. They are
primarily intended for applications where the a.c. component is small with respect to the rated
voltage.
Capacitors for electromagnetic interference suppression are not included, but are covered by
IEC 60384-14.
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 19: Rahmenspezifikation - Oberflächenmontierbare Gleichspannungs-Kondensatoren mit metallisierter Polyethylen-Terephtalat-Folie als Dielektrikum
Condensateurs fixes utilisés dans les équipements électroniques - Partie 19: Spécification intermédiaire: Condensateurs fixes pour montage en surface pour courant continu à diélectrique en film de polyéthylène téréphtalate métallisé
L'IEC 60384-19:2015 s'applique aux condensateurs fixes pour courant continu à électrodes métallisées et à diélectrique en polyéthylène téréphtalate destinés aux équipements électroniques. Ces condensateurs sont équipés de contacts de connexion métallisés ou de bandes de brasure et sont destinés à être montés directement sur des substrats pour circuits hybrides ou sur des cartes imprimées. Ces condensateurs peuvent avoir des propriétés "autocicatrisantes" en fonction des conditions d'utilisation. Ils sont principalement destinés à des applications dans lesquelles la composante alternative est petite par rapport à la tension assignée.
Les condensateurs d'antiparasitage ne sont pas inclus, mais ils sont couverts par l'IEC 60384-14. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) Révision de toutes les parties du document en se basant sur les Directives IEC, Partie 2 (sixième édition, 2011), dans la mesure du possible, et sur l'harmonisation d'autres types de documents.
b) Révision des tableaux et de l'Article 4 pour éviter les duplications et les contradictions.
Nespremenljivi kondenzatorji za elektronsko opremo - 19. del: Področna specifikacija - Nespremenljivi kondenzatorji za enosmerni tok za površinsko montažo s pokovinjenim polietilen-tereftalatnim dielektrikom
Ta del standarda IEC 60384 se uporablja za pritrjene kondenzatorje za površinsko namestitev za enosmerne napetosti z metaliziranimi elektrodami in polietilenskim tereftalatnim dielektrikom za uporabo v elektronski opremi. Ti kondenzatorji imajo metalizirane priključne blazinice ali varilne trakove ter so namenjeni namestitvi neposredno na podloge za hibridne tokokroge ali na tiskana vezja. Ti kondenzatorji imajo lahko »samoozdravljive lastnosti«, odvisno od pogojev uporabe. Namenjeni so predvsem uporabam, pri katerih je izmenična komponenta majhna glede na nazivno napetost.
Kondenzatorji za preprečevanje elektromagnetnih motenj niso vključeni, vendar so zajeti v standardu IEC 60384-14.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.URþQDSRYUãLQVNRFixed capacitors for use in electronic equipment - Part 19: Sectional specification - Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors31.060.10Fiksni kondenzatorjiFixed capacitorsICS:Ta slovenski standard je istoveten z:EN 60384-19:2015SIST EN 60384-19:2016en01-marec-2016SIST EN 60384-19:2016SLOVENSKI
STANDARDSIST EN 60384-19:20061DGRPHãþD
SIST EN 60384-19:2016
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 60384-19
December 2015 ICS 31.060.30
Supersedes
EN 60384-19:2006
English Version
Fixed capacitors for use in electronic equipment - Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors (IEC 60384-19:2015)
Condensateurs fixes utilisés dans les équipements électroniques - Partie 19: Spécification intermédiaire: Condensateurs fixes pour montage en surface pour courant continu à diélectrique en film de polyéthylène téréphtalate métallisé (IEC 60384-19:2015)
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 19: Rahmenspezifikation - Oberflächenmontierbare Gleichspannungs-Kondensatoren mit metallisierter Polyethylen-Terephtalat-Folie als Dielektrikum (IEC 60384-19:2015) This European Standard was approved by CENELEC on 2015-05-20. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60384-19:2015 E SIST EN 60384-19:2016
EN 60384-19:2015 (E) 2
European foreword The text of document 40/2342/FDIS, future edition 3 of IEC 60384-19, prepared by IEC/TC 40 "Capacitors and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60384-19:2015.
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2016-06-04 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-05-20
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60384-19:2015 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60068 series NOTE
Harmonized in EN 60068 series. IEC 60384-19-1 NOTE
Harmonized in EN 60384-19-1. SIST EN 60384-19:2016
EN 60384-19:2015 (E)
3
Annex ZA (normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year IEC 60062 -
Marking codes for resistors and capacitors EN 60062 -
+ corrigendum
2007
IEC 60063 -
Preferred number series for resistors and capacitors EN 60063 -
IEC 60068-1 2013
Environmental testing -- Part 1: General and guidance EN 60068-1 2014
IEC 60384-1 2008
Fixed capacitors for use in electronic equipment -- Part 1: Generic specification EN 60384-1 2009
IEC 61193-2 2007
Quality assessment systems -- Part 2: Selection and use of sampling plans for inspection of electronic components and packages EN 61193-2 2007
ISO 3 -
Preferred numbers; Series of preferred numbers - -
SIST EN 60384-19:2016
SIST EN 60384-19:2016
IEC 60384-19 Edition 3.0 2015-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Fixed capacitors for use in electronic equipment –
Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate
film dielectric surface mount d.c. capacitors
Condensateurs fixes utilisés dans les équipements électroniques –
Partie 19: Spécification intermédiaire: Condensateurs fixes pour montage en surface pour courant continu à diélectrique en film de polyéthylène téréphtalate métallisé
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 31.060.30
ISBN 978-2-8322-2596-7
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé. SIST EN 60384-19:2016
– 2 – IEC 60384-19:2015 IEC 2015
CONTENTS FOREWORD . 5 1 General . 7 1.1 Scope . 7 1.2 Object . 7 1.3 Normative references . 7 1.4 Information to be given in a detail specification . 8 1.4.1 General . 8 1.4.2 Outline drawing and dimensions . 8 1.4.3 Mounting . 8 1.4.4 Ratings and characteristics . 8 1.4.5 Marking . 9 1.5 Terms and definitions . 9 1.6 Marking . 9 1.6.1 General . 9 1.6.2 Information for marking . 9 1.6.3 Marking of capacitors . 9 1.6.4 Marking on packaging . 10 2 Preferred ratings and characteristics . 10 2.1 Preferred characteristics . 10 2.1.1 Preferred climatic categories . 10 2.2 Preferred values of ratings . 10 2.2.1 Nominal capacitance (CN) . 10 2.2.2 Tolerance on nominal capacitance . 10 2.2.3 Rated voltage (UR) . 10 2.2.4 Category voltage (UC) . 11 2.2.5 Rated temperature . 11 3 Quality assessment procedures . 11 3.1 Primary stage of manufacture . 11 3.2 Structurally similar components . 11 3.3 Certified test records of released lots . 11 3.4 Qualification approval procedures . 11 3.4.1 General . 11 3.4.2 Qualification approval on the basis of the fixed sample size procedure . 11 3.5 Quality conformance inspection . 19 3.5.1 Formation of inspection lots . 19 3.5.2 Test schedule . 20 3.5.3 Delayed delivery . 20 3.5.4 Assessment levels . 20 4 Test and measurement procedures . 21 4.1 Mounting . 21 4.2 Visual examination and check of dimensions . 21 4.2.1 General . 21 4.2.2 Visual examination and check of dimensions . 21 4.2.3 Requirements . 21 4.3 Electrical tests . 21 4.3.1 Voltage proof . 21 SIST EN 60384-19:2016
IEC 60384-19:2015 IEC 2015 – 3 –
4.3.2 Capacitance . 22 4.3.3 Tangent of loss angle (tan δ) . 22 4.3.4 Insulation resistance . 23 4.4 Shear test . 24 4.5 Substrate bending test . 25 4.5.1 General . 25 4.5.2 Initial inspections . 25 4.5.3 Final inspections and requirements . 25 4.6 Resistance to soldering heat . 25 4.6.1 General . 25 4.6.2 Initial inspections . 25 4.6.3 Test conditions . 25 4.6.4 Recovery . 25 4.6.5 Final inspections and requirements . 25 4.7 Solderability . 25 4.7.1 General . 25 4.7.2 Test conditions . 26 4.7.3 Final inspections and requirements . 26 4.8 Rapid change of temperature . 26 4.8.1 General . 26 4.8.2 Initial inspections . 26 4.8.3 Test conditions . 26 4.8.4 Final inspections and requirements . 26 4.9 Climatic sequence. 26 4.9.1 General . 26 4.9.2 Initial inspections . 26 4.9.3 Dry heat . 26 4.9.4 Damp heat, cyclic, test Db, first cycle . 27 4.9.5 Cold. 27 4.9.6 Damp heat, cyclic, test Db, remaining cycles . 27 4.9.7 Recovery . 27 4.9.8 Final inspections and requirements . 27 4.10 Damp heat, steady state . 27 4.10.1 General . 27 4.10.2 Initial inspections . 27 4.10.3 Test conditions . 27 4.10.4 Recovery . 27 4.10.5 Final inspections and requirements . 27 4.11 Endurance . 28 4.11.1 General . 28 4.11.2 Initial inspections . 28 4.11.3 Test conditions . 28 4.11.4 Final inspections and requirements . 28 4.12 Charge and discharge . 28 4.12.1 General . 28 4.12.2 Initial inspections . 28 4.12.3 Test conditions . 28 4.12.4 Recovery . 29 4.12.5 Final inspections and requirements . 29 SIST EN 60384-19:2016
– 4 – IEC 60384-19:2015 IEC 2015
4.13 Component solvent resistance (if applicable) . 29 4.14 Solvent resistance of marking (if applicable) . 29 Bibliography . 30
Table 1 – Percentage limit of the rated voltage at a.c. voltage frequency . 11 Table 2 – Test and sampling plan for qualification approval Assessment level EZ . 13 Table 3 – Test schedule for qualification approval . 14 Table 4 – Lot-by-lot inspection . 20 Table 5 – Periodic inspection . 21 Table 6 – Test voltages . 22 Table 7 – Applicable tan δ values . 23 Table 8 – Requirements regarding insulation resistance . 24 Table 9 – Correction factor dependent on temperature. 24 Table 10 – Test conditions . 28
SIST EN 60384-19:2016
IEC 60384-19:2015 IEC 2015 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 19: Sectional specification:
Fixed metallized polyethylene-terephthalate film
dielectric surface mount d.c. capacitors
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-19 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This third edition cancels and replaces the second edition published in 2006 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Revised all parts of the document based on the IEC Directives Part 2:2011 (sixth edition) to the extent practicable, and harmonization between other similar kind of documents. b) Revised tables and Clause 4 so as to prevent duplications and contradictions. SIST EN 60384-19:2016
– 6 – IEC 60384-19:2015 IEC 2015
The text of this standard is based on the following documents: FDIS Report on voting 40/2342/FDIS 40/2373/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The list of all parts of the IEC 60384 series, under the (new) general title Fixed capacitors for use in electronic equipment, can be found on the IEC web site. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be
• reconfirmed, • withdrawn, • replaced by a revised edition, or • amended.
SIST EN 60384-19:2016
IEC 60384-19:2015 IEC 2015 – 7 –
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 19: Sectional specification:
Fixed metallized polyethylene-terephthalate film
dielectric surface mount d.c. capacitors
1 General 1.1 Scope This part of IEC 60384 is applicable to fixed surface mount capacitors for direct current, with metallized electrodes and polyethylene-terephthalate dielectric for use in electronic equipment. These capacitors have metallized connecting pads or soldering strips and are intended to be mounted directly onto substrates for hybrid circuits or onto printed boards. These capacitors may have "self-healing properties" depending on conditions of use. They are primarily intended for applications where the a.c. component is small with respect to the rated voltage. Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14. 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60384-1:2008, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification shall be of equal or higher performance level, because lower performance levels are not permitted. 1.3 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60062, Marking codes for resistors and capacitors IEC 60063, Preferred number series for resistors and capacitors IEC 60068-1:2013, Environmental testing – Part 1: General and guidance IEC 60384-1:2008, Fixed capacitors for use in electronic equipment – Part 1: Generic specification IEC 61193-2:2007, Quality assessment systems – Part 2: Selection and use of sampling plans for inspection of electronic components and packages ISO 3, Preferred numbers – Series of preferred numbers SIST EN 60384-19:2016
– 8 – IEC 60384-19:2015 IEC 2015
1.4 Information to be given in a detail specification 1.4.1 General Detail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example by an asterisk. The information given in 1.4.2 may, for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause of this sectional specification. 1.4.2 Outline drawing and dimensions There shall be an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect inter-changeability and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimetres, however, when the original dimensions are given in inches, the converted metric dimensions in millimetres shall be added. The numerical values of the body shall be given as follows: – width, length and height. The numerical values of the terminals shall be given as follows: – width, length and spacing. When necessary, for example when a number of items (sizes and capacitance/voltage ranges) is covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. 1.4.3 Mounting The detail specification shall give guidance on methods of mounting for normal use. Mounting for test and measurement purposes (when required) shall be in accordance with 4.1. 1.4.4 Ratings and characteristics 1.4.4.1 General The ratings and characteristics shall be in accordance with the relevant clauses of this standard, together with the following. 1.4.4.2 Nominal capacitance range See 2.2.1. When products approved to the detail specification have different nominal capacitance ranges, the following statement should be added: “The nominal capacitance range available in each voltage range is given on the IEC online service, www.iecq.org/certificates." SIST EN 60384-19:2016
IEC 60384-19:2015 IEC 2015 – 9 –
1.4.4.3 Particular characteristics Additional characteristics may be listed, when they are considered necessary to specify adequately the component for design and application purposes. 1.4.4.4 Soldering The detail specification shall prescribe the test methods, severities and requirements applicable for the solderability and the resistance to soldering heat tests. 1.4.5 Marking The detail specification shall specify the content of the marking on the capacitor and on the packaging. Deviations from 1.6 shall be specifically stated. 1.5 Terms and definitions For the purposes of this document, and in addition to the applicable terms and definitions given in IEC 60384-1:2008, the following definitions apply. 1.5.1
performance grade 1 capacitors capacitors for long-life applications with stringent require
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.