SIST EN ISO 2247:2003
(Main)Packaging - Complete, filled transport packages and unit loads - Vibration tests at fixed low frequency (ISO 2247:2000)
Packaging - Complete, filled transport packages and unit loads - Vibration tests at fixed low frequency (ISO 2247:2000)
This specifies methods to carry out vibration tests on complete filled transport packages or unit load using sinusoidal excitation at fixed frequency.
Verpackung - Versandfertige Packstücke und Ladeeinheiten - Schwingprüfung mit niedriger Festfrequenz (ISO 2247:2000)
In dieser Internationalen Norm werden Verfahren zur Durchführung von Schwingprüfungen an versandferti-gen Packstücken oder Ladeeinheiten festgelegt, bei denen durch Anwendung einer Festfrequenz Sinus-schwingungen erzeugt werden. Diese Prüfungen dienen dazu, die Festigkeit von Packstücken und Ladeein-heiten oder den Schutz zu beurteilen, den sie dem Packstoff bieten, wenn sie Schwingungen mit niedriger Frequenz ausgesetzt werden. Sie dürfen entweder als Einzelprüfungen durchgeführt werden, um die Auswir-kungen von Schwingungen mit niedriger Frequenz zu untersuchen oder als Teil einer Prüffolge zur Ermittlung der Widerstandsfähigkeit einer Verpackung oder Ladeeinheit im Rahmen eines bestimmten Verteilungs-systems (Transportkette), das Bean-spruchungen durch Schwingungen mit niedriger Frequenz oder wieder-holte Stöße einschließt.
Emballages - Emballages d'expédition complets et pleins et charges unitaires - Essais de vibration a basse fréquence fixe (ISO 2247:2000)
La présente Norme internationale spécifie deux méthodes d'essai de vibration sur un emballage d'expédition
complet et plein ou une charge unitaire en utilisant une excitation sinusoïdale à fréquence fixe. De tels essais
peuvent être utilisés pour évaluer les caractéristiques des emballages et des charges unitaires en fonction de leur
résistance ou de la protection qu'ils offrent à leur contenu lorsqu'il sont soumis à des vibrations à basse fréquence.
Chacun de ces essais peut être effectué comme essai simple dans le but d'examiner les effets de telles vibrations,
ou il peut faire partie d'une série d'essais destinés à mesurer la résistance d'un emballage ou d'une charge unitaire
dans un système de distribution qui comprend un risque de vibration à basse fréquence ou lors de chocs répétitifs.
Embalaža - Celovita, napolnjena transportna embalaža - Vibracijski preskusi pri določeni nizki frekvenci (ISO 2247:2000)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 2247:2003
01-januar-2003
1DGRPHãþD
SIST EN 22247:1996
(PEDODåD&HORYLWDQDSROQMHQDWUDQVSRUWQDHPEDODåD9LEUDFLMVNLSUHVNXVLSUL
GRORþHQLQL]NLIUHNYHQFL ,62
Packaging - Complete, filled transport packages and unit loads - Vibration tests at fixed
low frequency (ISO 2247:2000)
Verpackung - Versandfertige Packstücke und Ladeeinheiten - Schwingprüfung mit
niedriger Festfrequenz (ISO 2247:2000)
Emballages - Emballages d'expédition complets et pleins et charges unitaires - Essais
de vibration a basse fréquence fixe (ISO 2247:2000)
Ta slovenski standard je istoveten z: EN ISO 2247:2002
ICS:
55.180.40 Celovita, napolnjena Complete, filled transport
transportna embalaža packages
SIST EN ISO 2247:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 2247:2003
---------------------- Page: 2 ----------------------
SIST EN ISO 2247:2003
EUROPEAN STANDARD
EN ISO 2247
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2002
ICS 55.180.40 Supersedes EN 22247:1992
English version
Packaging - Complete, filled transport packages and unit loads -
Vibration tests at fixed low frequency (ISO 2247:2000)
Emballages - Emballages d'expédition complets et pleins Verpackung - Versandfertige Packstücke und
et charges unitaires - Essais de vibration à basse Ladeeinheiten - Schwingprüfung mit niedriger Festfrequenz
fréquence fixe (ISO 2247:2000) (ISO 2247:2000)
This European Standard was approved by CEN on 26 August 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2247:2002 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 2247:2003
EN ISO 2247:2002 (E)
Foreword
The text of the International Standard from Technical Committee ISO/TC 122 "Packaging" of the
International Organization for Standardization (ISO) has been taken over as a European
Standard by Technical Committee CEN/TC 261 "Packaging", the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2003, and conflicting national
standards shall be withdrawn at the latest by March 2003.
This document supersedes EN 22247:1992.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of the International Standard ISO 2247:2000 has been approved by CEN as a
European Standard without any modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 2247:2003
EN ISO 2247:2002 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 2206 1987 Packaging - Complete, filled transport EN 22206 1992
packages - Identification of parts when
testing
ISO 2233 2000 Packaging - Complete, filled transport EN ISO 2233 2001
packages and unit loads - Conditioning
for testing
ISO 2234 1985 Packaging - Complete, filled transport EN 22234 1992
packages - Stacking test using static load
3
---------------------- Page: 5 ----------------------
SIST EN ISO 2247:2003
---------------------- Page: 6 ----------------------
SIST EN ISO 2247:2003
INTERNATIONAL ISO
STANDARD 2247
Third edition
2000-03-01
Packaging — Complete, filled transport
packages and unit loads — Vibration tests
at fixed low frequency
Emballages — Emballages d'expédition complets et pleins et charges
unitaires — Essais de vibration à basse fréquence fixe
Reference number
ISO 2247:2000(E)
©
ISO 2000
---------------------- Page: 7 ----------------------
SIST EN ISO 2247:2003
ISO 2247:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading
this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in
this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 2247:2003
ISO 2247:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 2247 was prepared by Technical Committee ISO/TC 122, Packaging, Subcommittee
SC 3, Performance requirements and tests for means of packaging, packages and unit loads (as required by
ISO/TC 122).
This third edition cancels and replaces the second edition (ISO 2247:1985), which has been technically revised.
Annex A forms a normative part of this International Standard.
© ISO 2000 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 2247:2003
ISO 2247:2000(E)
Introduction
It is the responsibility of the user of this International Standard to establish appropria
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.