SIST EN ISO 11299-3:2013
(Main)Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes (ISO 11299-3:2011)
Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes (ISO 11299-3:2011)
This part of ISO 11299, in conjunction with ISO 11299‑1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of gas supply networks. It is applicable to polyethylene (PE) pipes for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten Gasversorgungsnetzwerken - Teil 3: Close-Fit-Lining (ISO 11299-3:2011)
Dieser Teil der ISO 11299 legt in Verbindung mit ISO 11299-1 die Anforderungen und Prüfverfahren für Close-Fit-Lining-Systeme fest, die bei der Renovierung von Gasversorgungsnetzwerken verwendet werden.
Er gilt für Rohre aus Polyethylen (PE) sowohl für unabhängige als auch für interaktive Druck-Liner-Rohre und die dazugehörigen Formstücke und Verbindungen für den Bau des Lining-Systems.
Systèmes de canalisations en plastique pour la rénovation des réseaux de gaz enterrés - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11299-3:2011)
L'ISO 11299-3:2011, conjointement à l'ISO 11299-1, spécifie les exigences et les méthodes d'essai pour les systèmes de tubages par tuyau continu sans espace annulaire utilisés pour la rénovation des réseaux de gaz.
L'ISO 11299-3:2011 s'applique aux tuyaux en polyéthylène (PE) à la fois pour les tubages autostructurants et les tubages nécessitant le maintien de l'enveloppe, ainsi qu'aux raccords associés et aux assemblages pour la construction du système de rénovation.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo s plinom - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11299-3:2011)
Ta del standarda ISO 11299 v povezavi s standardom ISO 11299-1 določa zahteve in preskusne metode za tesno prilagodljive sisteme oblaganja, ki se uporabljajo za obnovo podzemnih omrežij za oskrbo s plinom. Uporablja se za cevi iz polietilena, ki so izdelane za neodvisne ter interaktivne obloge cevi s tlakom in povezane fitinge ter spoje za izdelavo sistema oblog.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11299-3:2013
01-april-2013
1DGRPHãþD
SIST EN 14408-3:2005
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo s
plinom - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11299-3:2011)
Plastics piping systems for renovation of underground gas supply networks - Part 3:
Lining with close-fit pipes (ISO 11299-3:2011)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten
Gasversorgungsnetzwerken - Teil 3: Close-Fit-Lining (ISO 11299-3:2011)
Systèmes de canalisations en plastique pour la rénovation des réseaux de gaz enterrés -
Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11299-3:2011)
Ta slovenski standard je istoveten z: EN ISO 11299-3:2013
ICS:
83.140.30 Cevi, fitingi in ventili iz Plastics pipes, fittings and
polimernih materialov valves
91.140.40 Sistemi za oskrbo s plinom Gas supply systems
SIST EN ISO 11299-3:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11299-3:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 11299-3:2013
EUROPEAN STANDARD
EN ISO 11299-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2013
ICS 23.040.20; 23.040.45; 75.200 Supersedes EN 14408-3:2004
English Version
Plastics piping systems for renovation of underground gas
supply networks - Part 3: Lining with close-fit pipes (ISO 11299-
3:2011)
Systèmes de canalisations en plastique pour la rénovation Kunststoff-Rohrleitungssysteme für die Renovierung von
des réseaux de gaz enterrés - Partie 3: Tubage par tuyau erdverlegten Gasversorgungsnetzwerken - Teil 3: Close-Fit-
continu sans espace annulaire (ISO 11299-3:2011) Lining (ISO 11299-3:2011)
This European Standard was approved by CEN on 5 February 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11299-3:2013: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11299-3:2013
EN ISO 11299-3:2013 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11299-3:2013
EN ISO 11299-3:2013 (E)
Foreword
The text of ISO 11299-3:2011 has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings
and valves for the transport of fluids” of the International Organization for Standardization (ISO) and has been
taken over as EN ISO 11299-3:2013 by Technical Committee CEN/TC 155 “Plastics piping systems and
ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2013, and conflicting national standards shall be withdrawn at
the latest by August 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14408-3:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11299-3:2011 has been approved by CEN as EN ISO 11299-3:2013 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11299-3:2013
---------------------- Page: 6 ----------------------
SIST EN ISO 11299-3:2013
INTERNATIONAL ISO
STANDARD 11299-3
First edition
2011-09-15
Plastics piping systems for renovation of
underground gas supply networks
Part 3:
Lining with close-fit pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux de
gaz enterrés — Partie 3: Tubage par tuyau continu sans espace annulaire
Reference number
ISO 11299-3:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 11299-3:2013
ISO 11299-3:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11299-3:2013
ISO 11299-3:2011(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 General . 1
3.2 Techniques . 2
3.3 Characteristics . 2
3.4 Materials . 2
3.5 Product stages . 2
3.6 Service conditions . 2
3.7 Joints . 2
4 Symbols and abbreviated terms . 3
4.1 Symbols . 3
4.2 Abbreviated terms . 3
5 Pipes at the “M” stage . 3
5.1 Materials . 3
5.2 General characteristics . 4
5.3 Material characteristics . 4
5.4 Geometric characteristics . 4
5.5 Mechanical characteristics . 4
5.6 Physical characteristics . 5
5.7 Jointing . 5
5.8 Marking . 5
6 Fittings at the “M” stage . 5
7 Ancillary components . 5
8 Fitness for purpose of the installed lining system at the “I” stage . 5
8.1 Materials . 5
8.2 General characteristics . 5
8.3 Material characteristics . 5
8.4 Geometric characteristics . 6
8.5 Mechanical characteristics . 6
8.6 Physical characteristics . 7
8.7 Additional characteristics . 7
8.8 Sampling . 8
9 Installation practice . 8
9.1 Preparatory work . 8
9.2 Storage, handling and transport of pipes and fittings . 8
9.3 Equipment . 8
9.4 Installation . 9
9.5 Process-related inspection and testing .10
Annex A (normative) Factory-folded heat-reverted polyethylene (PE) pipe — Determination of memory
ability . 11
Bibliography .13
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11299-3:2013
ISO 11299-3:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11299-3 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the
transport of fluids.
ISO 11299 consists of the following parts, under the general title Plastics piping systems for renovation of
underground gas supply networks:
— Part 1: General
— Part 3: Lining with close-fit pipes
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11299-3:2013
ISO 11299-3:2011(E)
Introduction
This part of ISO 11299 is part of a system standard for plastics piping systems of various materials used for the
renovation of existing pipelines in a specified application area. System standards for renovation deal with the
following applications:
— plastics piping systems for renovation of underground non-pressure drainage and sewerage networks;
— plastics piping systems for renovation of underground drainage and sewerage networks under pressure;
— plastics piping systems for renovation of underground water supply networks;
— plastics piping systems for renovation of underground gas supply networks (this application).
These system standards are distinguished from those for conventionally installed plastics piping systems
because they set requirements for certain characteristics in the as-installed condition, after site processing.
This is in addition to verification of characteristics of plastics piping systems as manufactured.
This system standard comprises a Part 1: General and all applicable parts relating to the renovation technique
family, from the following:
— Part 2: Lining with continuous pipes
— Part 3: Lining with close-fit pipes (this document)
— Part 4: Lining with cured-in-place pipes
— Part 6: Lining with adhesive-backed hoses
The requirements for any given renovation technique family are specified in this part of ISO 11299 and are
applied in conjunction with the relevant other part. For example, both ISO 11299-1 and this part of ISO 11299
specify the requirements relating to lining with close-fit pipes. For complementary information, see ISO 11295.
Not all technique families are pertinent to every area of application and this is reflected in the part numbers
included in each system standard.
A consistent structure of clause headings has been adopted for all parts of ISO 11299, in order to facilitate
direct comparisons across renovation technique families.
Figure 1 illustrates the common part and clause structure and the relationship between ISO 11299 and the
system standards for other application areas.
© ISO 2011 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 11299-3:2013
ISO 11299-3:2011(E)
Figure 1 — Format of the renovation system standards
vi © ISO 2011 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 11299-3:2013
INTERNATIONAL STANDARD ISO 11299-3:2011(E)
Plastics piping systems for renovation of underground gas
supply networks
Part 3:
Lining with close-fit pipes
1 Scope
This part of ISO 11299, in conjunction with ISO 11299-1, specifies requirements and test methods for close-fit
lining systems intended to be used for the renovation of gas supply networks.
It is applicable to polyethylene (PE) pipes for both independent and interactive pressure pipe liners as well as
associated fittings and joints for the construction of the lining system.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
ISO 4437:2007, Buried polyethylene (PE) pipes for the supply of gaseous fuels — Metric series — Specifications
ISO 8085-3, Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels — Metric
series — Specifications — Part 3: Electrofusion fittings
ISO 11299-1:2011, Plastics piping systems for renovation of underground gas supply networks — Part 1: General
ISO 12176-1, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
ISO 12176-2, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2:
Electrofusion
3 Terms and definitions
For the purposes of this document, the terms, definitions, symbols and abbreviations given in ISO 11299-1 and
the following apply.
3.1 General
3.1.1
close fit
situation of the outside of the installed liner relative to the inside of the existing pipeline, which may either be an
interference fit or include a small annular gap resulting from shrinkage and tolerances only
3.1.2
close-fit pipe
continuous lining pipe of thermoplastic material reshaped or otherwise expanded after insertion to achieve a
close fit to the existing pipeline
© ISO 2011 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 11299-3:2013
ISO 11299-3:2011(E)
3.2 Techniques
No additional definitions apply.
3.3 Characteristics
3.3.1
maximum mean outside diameter
d
em,max
maximum value of the mean outside diameter as specified for a given nominal size
3.4 Materials
No additional definitions apply.
3.5 Product stages
No additional definitions apply.
3.6 Service conditions
3.6.1
maximum operating pressure
MOP
maximum effective pressure of the fluid in the piping system which is allowed in continuous use
5 2
NOTE 1 MOP is expressed in bar, where 1 bar = 0,1 MPa = 10 Pa; 1 MPa = 1 N/mm.
NOTE 2 It takes into account the physical and the mechanical characteristics of the components of a piping system.
NOTE 3 It is calculated using the following equation:
20× MRS
( )
MOP =
C×(SDR−1)
3.7 Joints
3.7.1
electrofusion joint
joint between a PE socket or saddle electrofusion fitting and a pipe or fitting with spigotted ends, made by
heating the electrofusion fittings by the Joule effect of the heating element incorporated at their jointing
surfaces, causing the material adjacent to them to melt and pipe and fitting surfaces to fuse
3.7.2
butt fusion joint
joint made by heating the planed ends of matching surfaces by holding them against a flat heating plate until
the PE material reaches fusion temperature, quickly removing the heating plate and pushing the two softened
ends against one another
3.7.3
mechanical joint
joint made by assembling a PE pipe to another PE pipe, or any other element of the piping system that generally
includes a compression part, to provide for pressure integrity, leaktightness and resistance to end loads
NOTE A support sleeve inserted into the pipe bore can be used to provide a permanent support for the PE pipe to
prevent creep in the pipe wall under radial compressive forces.
2 © ISO 2011 – All rights reserved
----------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.