SIST EN 840-3:2020
(Main)Mobile waste and recycling containers - Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices - Dimensions and design
Mobile waste and recycling containers - Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices - Dimensions and design
This European Standard specifies dimensions and design requirements of mobile waste and recycling containers with 4 wheels, with dome lid(s) and capacity up to 1 300 l to be used by trunnion and/or comb lifting device.
Fahrbare Abfall- und Wertstoffbehälter - Teil 3: Behälter mit 4 Rädern und einem Nennvolumen bis 1 300 l mit Schiebedeckel(n), für Schüttungen mit Zapfenaufnahme und/oder für Kammschüttungen - Maße und Formgebung
Dieses Dokument legt Maße und Anforderungen an die Gestaltung von fahrbaren Abfall- und Wertstoffbehältern mit 4 Rädern, mit Schiebedeckel(n) und einem Nennvolumen bis 1 300 l für Schüttungen für Zapfenaufnahme und/oder Kammschüttungen fest.
Conteneurs roulants à déchets et de recyclage - Partie 3 : Conteneurs à 4 roues de capacité inférieure ou égale à 1 300 l à couvercle(s) bombé(s), pour lève-conteneurs par tourillon et/ou à peigne - Dimensions et conception
Le présent document spécifie les dimensions et les exigences de conception pour les conteneurs roulants à déchets et de recyclage à 4 roues à couvercle(s) bombé(s) dont la capacité est inférieure ou égale à 1 300 l, pour lève-conteneurs à tourillon et/ou à peigne.
Premični zabojniki za odpadke in za recikliranje - 3. del: Zabojniki na štirih kolesih s prostornino do 1300 l in izbočenim(-i) pokrovom(-i) za iztresalnike z rokama in/ali glavnikom - Mere in oblika
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 840-3:2020
01-junij-2020
Nadomešča:
SIST EN 840-3:2014
Premični zabojniki za odpadke in za recikliranje - 3. del: Zabojniki na štirih kolesih
s prostornino do 1300 l in izbočenim(-i) pokrovom(-i) za iztresalnike z rokama in/ali
glavnikom - Mere in oblika
Mobile waste and recycling containers - Part 3: Containers with 4 wheels with a capacity
up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices - Dimensions and
design
Fahrbare Abfall- und Wertstoffbehälter - Teil 3: Behälter mit 4 Rädern und einem
Nennvolumen bis 1 300 l mit Schiebedeckel(n), für Schüttungen mit Zapfenaufnahme
und/oder für Kammschüttungen - Maße und Formgebung
Conteneurs roulants à déchets et de recyclage - Partie 3 : Conteneurs à 4 roues de
capacité inférieure ou égale à 1 300 l à couvercle(s) bombé(s), pour lève-conteneurs par
tourillon et/ou à peigne - Dimensions et conception
Ta slovenski standard je istoveten z: EN 840-3:2020
ICS:
13.030.40 Naprave in oprema za Installations and equipment
odstranjevanje in obdelavo for waste disposal and
odpadkov treatment
SIST EN 840-3:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 840-3:2020
---------------------- Page: 2 ----------------------
SIST EN 840-3:2020
EN 840-3
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2020
EUROPÄISCHE NORM
ICS 13.030.40 Supersedes EN 840-3:2012
English Version
Mobile waste and recycling containers - Part 3: Containers
with 4 wheels with a capacity up to 1 300 l with dome
lid(s), for trunnion and/or comb lifting devices -
Dimensions and design
Conteneurs roulants à déchets et de recyclage - Partie 3 Fahrbare Abfall- und Wertstoffbehälter - Teil 3:
: Conteneurs à 4 roues de capacité inférieure ou égale à Behälter mit 4 Rädern und einem Nennvolumen bis 1
1 300 l à couvercle(s) bombé(s), pour lève-conteneurs 300 l mit Schiebedeckel(n), für Schüttungen mit
par tourillon et/ou à peigne - Dimensions et Zapfenaufnahme und/oder für Kammschüttungen -
conception Maße und Formgebung
This European Standard was approved by CEN on 7 October 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 840-3:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 840-3:2020
EN 840-3:2020 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Volumes . 5
5 Dimensions and design . 5
6 Nominal mass . 6
7 Safety and health requirements . 6
8 Testing . 6
9 Marking . 6
10 Designation. 7
Bibliography . 18
2
---------------------- Page: 4 ----------------------
SIST EN 840-3:2020
EN 840-3:2020 (E)
European foreword
This document (EN 840-3:2020) has been prepared by Technical Committee CEN/TC 183 “Waste
management”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards shall
be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 840-3:2012.
The main changes compared to the previous edition are listed below:
a) Figure 2 "System dimensions design B (type plastic)" and Figure 3 "System dimensions design C
(type metal)" have been updated;
b) Figure 9 "Handles above trunnion (type metal)" and Figure 10 "Functional dimension for frontal
receivers" have been added;
c) former Annex A "Recommendations for manufacturers of lifting devices" has been deleted;
d) document has been editorially revised and adapted to the new design rules.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 840-3:2020
EN 840-3:2020 (E)
1 Scope
This document specifies dimensions and design requirements of mobile waste and recycling containers
with 4 wheels, with dome lid(s) and capacity up to 1 300 l to be used by trunnion and/or comb lifting
device.
These containers are only approved for the before explicitly mentioned lifting devices.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 840-5, Mobile waste and recycling containers — Part 5: Performance requirements and test methods
EN 840-6, Mobile waste and recycling containers — Part 6: Safety and health requirements
1
EN 1501-5:— , Refuse collection vehicles — General requirements and safety requirements — Part 5:
Lifting devices for refuse collection vehicles
EN ISO 11469, Plastics - Generic identification and marking of plastics products (ISO 11469)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
NOTE Terms for components of mobile waste containers and lifting devices in three languages are given in
Annex A of EN 840-1:2020.
3.1
mobile waste container
appropriately designed container fitted with wheels intended to temporarily store waste
3.2
lifting device
structure which picks-up, tilts and empties containers
3.3
comb lifting device
lifting device in which the picking-up system consists of a row of teeth and a locking system to retain
the container during emptying
1
Under preparation. Stage at the time of publication: FprEN 1501-5.
4
---------------------- Page: 6 ----------------------
SIST EN 840-3:2020
EN 840-3:2020 (E)
3.4
trunnion lifting device
lifting device in which the picking-up system consists of a pair of arms with automatic locking
mechanism to fit the trunnion to retain the container during emptying
3.5
volume
total space inside the container when the lid is closed
3.6
nominal volume
capacity
volume stated by the manufacturer
Note 1 to entry: See Table 1 without tolerances.
Note 2 to entry: The English term “capacity” and the French term “capacité” are translated in the German
version by the term “Nennvolumen”.
3.7
nominal mass
mass, which is calculated as given in Clause 6
3.8
total permissible mass
mass of the container plus the nominal load
3.9
functional and safety dimension
essential dimensions which ensure the functionality and interchangeability of the container with the
compatible lifting device and which are necessary for the operator's safety and health
4 Volumes
This part of EN 840 identifies the two classes of containers:
— Class I - small size (nominal volume up to 1 000 l);
— Class II - large size (nominal volume between 1 000 l and 1 300 l).
Within the two above-mentioned classes of containers the following volumes are identified: 770 l,
1 000 l, 1 100 l and 1 300 l. Nominal volumes different from those referenced can be used by agreement
between user and manufacturer. The tolerance of the volumes shall be ± 5 % maximum measured
according to EN 840-5.
5 Dimensions and design
5.1 The design of the containers need not correspond to the drawings given in Figures 1 to 3. The
functional dimensions given in Table 1 shall be respected. Recommendations for manufacturers of
lifting devices are given in EN 1501-5:—.
5.2 The container shall be constructed so that when it is unloaded or loaded wit
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.