SIST EN ISO 15613:2004
(Main)Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004)
Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004)
This European Standard is a part of a series of standards, details of this series are given in prEN ISO 15607:2000, annex A.
This standard specifies how a preliminary welding procedure specification is qualified based on pre-production welding tests.
This standard is applicable to arc welding, gas welding, beam welding, resistance welding, stud welding and friction welding of metallic materials.
The use of this standard can be restricted by an application standard or specification.
Anforderung und Anerkennung von Schweißverfahren für metaltallische Werkstoffe - Qualifizierung aufgrund einer vorgezogenen Arbeitsprüfung (ISO 15613:2004)
Diese Norm legt die Bedingungen für die Anerkennung eines Schweißverfahrens aufgrund von Schweißverfahrensprüfungen vor Fertigungsbeginn in Übereinstimmung mit prEN ISO 15607 fest. Zusätzlich sind der Geltungsbereich und die Gültigkeitsdauer angegeben. Diese Norm ist Teil einer Normenreihe. Anhang A gibt die Einzelheiten dieser Normenreihe wieder. Diese Norm ist anwendbar für das Schweißen von metallischen Werkstoffen. Irgendwelche anderen Schweißprozesse können durch Vereinbarung zwischen den Vertragspartnern anerkannt werden.
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Qualification sur la base d'un assemblage soudé de préproduction (ISO 15613:2004)
La présente norme européenne spécifie les conditions de qualification d'un mode opératoire de soudage par exécution d'assemblages soudés particuliers préalables a la production conformément au prEN ISO 15607. De plus, elle précise le domaine de qualification et les limites de validité. La présente norme fait partie d'une série de normes. L'annexe A fournit des détails sur cette série de normes. La présente norme européenne est applicable au soudage par fusion des matériaux métalliques. D'autres procédés de soudage peuvent etre acceptés par accord entre les parties contractantes.
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Razvrščanje na podlagi predproizvodnega preskusa varjenja (ISO 15613:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15613:2004
01-september-2004
1DGRPHãþD
SIST EN 288-8:1996
3RSLVLQNYDOLILNDFLMDYDULOQLKSRVWRSNRY]DNRYLQVNHPDWHULDOH5D]YUãþDQMHQD
SRGODJLSUHGSURL]YRGQHJDSUHVNXVDYDUMHQMD ,62
Specification and qualification of welding procedures for metallic materials - Qualification
based on pre-production welding test (ISO 15613:2004)
Anforderung und Anerkennung von Schweißverfahren für metaltallische Werkstoffe -
Qualifizierung aufgrund einer vorgezogenen Arbeitsprüfung (ISO 15613:2004)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Qualification sur la base d'un assemblage soudé de préproduction (ISO
15613:2004)
Ta slovenski standard je istoveten z: EN ISO 15613:2004
ICS:
25.160.10
SIST EN ISO 15613:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 15613
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2004
ICS 25.160.10
English version
Specification and qualification of welding procedures for metallic
materials - Qualification based on pre-production welding test
(ISO 15613:2004)
Descriptif et qualification d'un mode opératoire de soudage Anforderung und Anerkennung von Schweißverfahren für
pour les matériaux métalliques - Qualification sur la base metaltallische Werkstoffe - Qualifizierung aufgrund einer
d'un assemblage soudé de préproduction (ISO vorgezogenen Arbeitsprüfung (ISO 15613:2004)
15613:2004)
This European Standard was approved by CEN on 7 May 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15613:2004: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 15613:2004 (E)
Contents
page
Foreword.3
Introduction .4
1 Scope.5
2 Normative references.5
3 Terms and definitions.6
4 Preliminary welding procedure specifications (pWPS) .6
5 Qualification of the welding procedure .6
6 Welding of test pieces.6
7 Testing.6
7.1 Fusion welding.6
7.2 Resistance welding.7
7.2.1 General.7
7.2.2 Overlap welding.7
7.2.3 Butt welding.7
8 Range of qualification .7
9 Validity.7
10 Welding procedure qualification record (WPQR) .8
Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other
provisions of EU directives .9
2
---------------------- Page: 3 ----------------------
EN ISO 15613:2004 (E)
Foreword
This document (EN ISO 15613:2004) has been prepared by Technical Committee CEN/TC 121 "Welding", the
secretariat of which is held by DS, in collaboration with Technical Committee ISO/TC 44 "Welding and allied
processes".
This European Standard EN ISO 15613:2003 shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by December 2004, and conflicting national standards shall be
withdrawn at the latest by December 2004.
This document supersedes EN 288-8:1995.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
3
---------------------- Page: 4 ----------------------
EN ISO 15613:2004 (E)
Introduction
In EN ISO 15607, one of the methods of welding procedure qualification is based on pre-production welding test.
Qualification based on a pre-production welding test can be used where the shape and dimensions of the standard
test pieces (e.g. those of prEN ISO 15614) do not adequately represent the joint to be welded.
In such cases, one or more special test pieces can be made to simulate the production joint in all essential
features, e.g. dimensions, restraint, heat sink effects, limited access. In the case of resistance welding, actual
components have to be used for the pre-production test.
4
---------------------- Page: 5 ----------------------
EN ISO 15613:2004 (E)
1 Scope
This European Standard is a part of a series of standards, details of this series are given in EN ISO 15607:2003,
annex A.
This standard specifies how a preliminary welding procedure specification is qualified based on pre-production
welding tests.
The principles of this standard may be applied to other welding processes.
This standard is applicable to arc welding, gas welding, beam welding, resistance welding, stud welding and friction
welding of metallic materials.
The use of this standard can be restricted by an application standard or specification.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN ISO 15607:2003, Specification and qualification of welding procedures for metallic materials - General rules
(ISO 15607:2003).
CR ISO 15608:2000, Welding - Gui
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.