Specification for radio disturbance and immunity measuring apparatus and methods - Part 2-2: Methods of measurement of disturbances and immunity - Measurement of disturbance power

This part of CISPR 16 specifies the methods of measurement of disturbance power using the absorbing clamp in the frequency range 30 MHz to 1 000 MHz.
NOTE In accordance with IEC Guide 107, CISPR 16-2-2 is a basic EMC publication for use by product committees of the IEC. As stated in Guide 107, product committees are responsible for determining the applicability of the EMC standard. CISPR and its sub-committees are prepared to co-operate with product committees in the determination of the value of particular EMC tests for specific products.

Anforderungen an Geräte und Einrichtungen sowie Festlegung der Verfahren zur Messung der hochfrequenten Störaussendung (Funkstörungen) und Störfestigkeit - Teil 2-2: Verfahren zur Messung der hochfrequenten Störaussendung (Funkstörungen) und Störfestigkeit - Messung der Störleistung

Spécifications des méthodes et des appareils de mesure des perturbations radioélectriques et de l'immunité aux perturbations radioélectriques - Partie 2-2: Méthodes de mesure des perturbations et de l'immunité - Mesure de la puissance perturbatrice

La CISPR 16-2-2:2010 spécifie la méthode de mesure de la puissance perturbatrice, utilisant la pince absorbante, dans la gamme de fréquences de 30 MHz à 1 000 MHz. Cette deuxième édition annule et remplace la première édition (2003), son Amendement 1 (2004) et son Amendement 2 (2005). Elle constitue une révision technique. Elle contient les modifications techniques significatives suivantes par rapport à l'édition précédente: des dispositions relatives à l'utilisation d'analyseurs de spectre pour les mesures de conformité (Annexe D) et l'utilisation d'appareils d'essai à FFT (Articles 3, 6 et 8) sont désormais incluses. La CISPR 16-2-2:2010 a le statut d'une publication fondamentale en CEM conformément au Guide 107 de la CEI, Compatibilité électromagnétique - Guide pour la rédaction des publications sur la compatibilité électromagnétique.

Specifikacija za merilne naprave in metode za merjenje radijskih motenj in odpornosti - 2-2. del: Metode za merjenje radijskih motenj in odpornosti - Merjenje moči motenj (CISPR 16-2-2:2010)

Ta del CISPR 16 opredeljuje metode za merjenje moči motenj z uporabo absorpcijske sponke v frekvenčnem razponu od 30 MHz do 1000 MHz.
OPOMBA: V skladu z Vodilom IEC 107 je CISPR 16-2-2 osnovna objava EMC, ki jo uporabljajo odbori za proizvode IEC. Kot je navedeno v Vodilu 107, so odbori za proizvode odgovorni za določevanje uporabe tega standarda EMC. CISPR in njegovi pododbori so pripravljeni sodelovati z odbori za proizvode pri določevanju vrednosti posameznih preskusov EMC za nekatere proizvode.

General Information

Status
Published
Public Enquiry End Date
28-Feb-2010
Publication Date
11-May-2011
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
07-Apr-2011
Due Date
12-Jun-2011
Completion Date
12-May-2011

Relations

Buy Standard

Standard
EN 55016-2-2:2011 - BARVE
English language
49 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 55016-2-2:2011
01-junij-2011
1DGRPHãþD
SIST EN 55016-2-2:2005
SIST EN 55016-2-2:2005/A1:2005
SIST EN 55016-2-2:2005/A2:2005
6SHFLILNDFLMD]DPHULOQHQDSUDYHLQPHWRGH]DPHUMHQMHUDGLMVNLKPRWHQMLQ
RGSRUQRVWLGHO0HWRGH]DPHUMHQMHUDGLMVNLKPRWHQMLQRGSRUQRVWL0HUMHQMH
PRþLPRWHQM &,635
Specification for radio disturbance and immunity measuring apparatus and methods -
Part 2-2: Methods of measurement of disturbances and immunity - Measurement of
disturbance power
Anforderungen an Geräte und Einrichtungen sowie Festlegung der Verfahren zur
Messung der hochfrequenten Störaussendung (Funkstörungen) und Störfestigkeit - Teil
2-2: Verfahren zur Messung der hochfrequenten Störaussendung (Funkstörungen) und
Störfestigkeit - Messung der Störleistung
Spécifications des méthodes et des appareils de mesure des perturbations
radioélectriques et de l'immunité aux perturbations radioélectriques - Partie 2-2:
Méthodes de mesure des perturbations et de l'immunité - Mesure de la puissance
perturbatrice
Ta slovenski standard je istoveten z: EN 55016-2-2:2011
ICS:
17.220.20 0HUMHQMHHOHNWULþQLKLQ Measurement of electrical
PDJQHWQLKYHOLþLQ and magnetic quantities
33.100.20 Imunost Immunity
SIST EN 55016-2-2:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 55016-2-2:2011

---------------------- Page: 2 ----------------------

SIST EN 55016-2-2:2011

EUROPEAN STANDARD
EN 55016-2-2

NORME EUROPÉENNE
April 2011
EUROPÄISCHE NORM

ICS 33.100.10; 33.100.20 Supersedes EN 55016-2-2:2004 + A1:2005 + A2:2005


English version


Specification for radio disturbance and immunity measuring apparatus
and methods -
Part 2-2: Methods of measurement of disturbances and immunity -
Measurement of disturbance power
(CISPR 16-2-2:2010)


Spécifications des méthodes et des Anforderungen an Geräte und
appareils de mesure des perturbations Einrichtungen sowie Festlegung der
radioélectriques et de l'immunité aux Verfahren zur Messung der
perturbations radioélectriques - hochfrequenten Störaussendung
Partie 2-2: Méthodes de mesure des (Funkstörungen) und Störfestigkeit -
perturbations et de l'immunité - Teil 2-2: Verfahren zur Messung der
Mesure de la puissance perturbatrice hochfrequenten Störaussendung
(CISPR 16-2-2:2010) (Funkstörungen) und Störfestigkeit -
Messung der Störleistung
(CISPR 16-2-2:2010)


This European Standard was approved by CENELEC on 2011-01-02. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 55016-2-2:2011 E

---------------------- Page: 3 ----------------------

SIST EN 55016-2-2:2011
EN 55016-2-2:2011 - 2 -
Foreword
The text of document CISPR/A/877/CDV, future edition 2 of CISPR 16-2-2, prepared by CISPR SC A,
Radio-interference measurements and statistical methods, was submitted to the IEC-CENELEC parallel
vote and was approved by CENELEC as EN 55016-2-2 on 2011-01-02.
This European Standard supersedes EN 55016-2-2:2004 + A1:2005 + A2:2005.
This EN 55016-2-2:2011 includes the following significant technical changes with respect to
EN 55016-2-2:2004 + A1:2005 + A2:2005: provisions for the use of spectrum analyzers for compliance
measurements (Annex D) and the use of FFT-based test instrumentation (Clauses 3, 6 and 8) are now
included.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-10-02
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2014-01-02
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard CISPR 16-2-2:2010 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
[1] CISPR 13 NOTE  Harmonized as EN 55013.
[2] CISPR 14-1:2005 NOTE  Harmonized as EN 55014-1:2006 (not modified).
[3] CISPR 16-2-1:2008 NOTE  Harmonized as EN 55016-2-1:2009 (not modified).
__________

---------------------- Page: 4 ----------------------

SIST EN 55016-2-2:2011
- 3 - EN 55016-2-2:2011
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

CISPR 16-1-1 2010 Specification for radio disturbance and EN 55016-1-1 2010
immunity measuring apparatus and methods -
Part 1-1: Radio disturbance and immunity
measuring apparatus - Measuring apparatus


CISPR 16-1-3 2004 Specification for radio disturbance and EN 55016-1-3 2006
immunity measuring apparatus and methods -
Part 1-3: Radio disturbance and immunity
measuring apparatus - Ancillary equipment -
Disturbance power


1) 2)
CISPR 16-1-4 - Specification for radio disturbance and EN 55016-1-4 2010
immunity measuring apparatus and methods -
Part 1-4: Radio disturbance and immunity
measuring apparatus - Antennas and test
sites for radiated disturbance measurements


1) 2)
CISPR 16-4-2 - Specification for radio disturbance and EN 55016-4-2 2004
immunity measuring apparatus and methods -
Part 4-2: Uncertainties, statistics and limit
modelling - Uncertainty in EMC
measurements


IEC 60050-161 1990 International Electrotechnical Vocabulary - -
(IEV) -
Chapter 161: Electromagnetic compatibility






1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 5 ----------------------

SIST EN 55016-2-2:2011

---------------------- Page: 6 ----------------------

SIST EN 55016-2-2:2011

CISPR 16-2-2
®
Edition 2.0 2010-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES
BASIC EMC PUBLICATION
PUBLICATION FONDAMENTALE EN CEM
Specification for radio disturbance and immunity measuring apparatus
and methods –
Part 2-2: Methods of measurement of disturbances and immunity –
Measurement of disturbance power

Spécifications des méthodes et des appareils de mesure des perturbations
radioélectriques et de l'immunité aux perturbations radioélectriques –
Partie 2-2: Méthodes de mesure des perturbations et de l'immunité –
Mesure de la puissance perturbatrice

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
X
CODE PRIX
ICS 33.100.10; 33.100.20 ISBN 978-2-88912-097-0
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 55016-2-2:2011
– 2 – CISPR 16-2-2 © IEC:2010
CONTENTS
FOREWORD.5
1 Scope.7
2 Normative references.7
3 Terms and definitions .7
4 Types of disturbance to be measured.12
4.1 General .12
4.2 Types of disturbance .12
4.3 Detector functions .12
5 Connection of measuring equipment .13
5.1 General .13
5.2 Connection of ancillary equipment.13
6 General measurement requirements and conditions .13
6.1 General .13
6.2 Disturbance not produced by the equipment under test .13
6.2.1 General .13
6.2.2 Compliance testing .13
6.3 Measurement of continuous disturbance .13
6.3.1 Narrowband continuous disturbance.13
6.3.2 Broadband continuous disturbance.14
6.3.3 Use of spectrum analyzers and scanning receivers.14
6.4 Operating conditions of the EUT .14
6.4.1 General .14
6.4.2 Normal load conditions.14
6.4.3 The time of operation.14
6.4.4 Running-in time .14
6.4.5 Supply .14
6.4.6 Mode of operation.14
6.5 Interpretation of measuring results.14
6.5.1 Continuous disturbance .14
6.5.2 Discontinuous disturbance .15
6.5.3 Measurement of the duration of disturbances .15
6.6 Measurement times and scan rates for continuous disturbance .15
6.6.1 General .15
6.6.2 Minimum measurement times .15
6.6.3 Scan rates for scanning receivers and spectrum analyzers .16
6.6.4 Scan times for stepping receivers .17
6.6.5 Strategies for a spectrum overview using the peak detector.18
6.6.6 Timing considerations using FFT-based instruments .21
7 Measurements using the absorbing clamp.23
7.1 Introduction to ACMM .23
7.2 Application of the absorbing clamp measurement method .24
7.2.1 General .24
7.2.2 Frequency range.24
7.2.3 EUT unit dimensions.24
7.2.4 LUT requirements .24
7.3 Requirements for measurements instrumentation and test site .24

---------------------- Page: 8 ----------------------

SIST EN 55016-2-2:2011
CISPR 16-2-2 © IEC:2010 – 3 –
7.3.1 General .24
7.3.2 Measuring receiver .24
7.3.3 Absorbing clamp assembly.24
7.3.4 Absorbing clamp test site requirements .25
7.4 Ambient requirements.26
7.5 EUT leads requirements .26
7.5.1 General .26
7.5.2 Lead under test.26
7.5.3 Leads not under test .27
7.6 Test set-up requirements .27
7.6.1 General .27
7.6.2 EUT set-up .27
7.6.3 LUT set-up.28
7.6.4 Absorbing clamp .29
7.6.5 Measurement cable.29
7.7 Operating conditions of the EUT .29
7.8 Measurement procedure .29
7.8.1 Ambient measurement procedure.29
7.8.2 EUT measurement procedure .29
7.9 Determination of disturbance power .31
7.10 Determination of the measurement uncertainty.31
7.11 Compliance criteria.31
8 Automated measurement of emissions.32
8.1 Precautions for automating measurements.32
8.2 Generic measurement procedure .32
8.3 Prescan measurements .33
8.3.1 Purpose.33
8.3.2 Determination of the required measurement time .33
8.3.3 Defining the prescan measurement .33
8.4 Data reduction .34
8.5 Emission maximization and final measurement .34
8.6 Post processing and reporting.34
8.7 Emission measurement strategies with FFT-based measuring instruments .34
Annex A (informative) Historical background to the method of measurement of the
interference power produced by electrical household and similar appliances in the VHF
range (see 7.1) .35
Annex B (informative) Use of spectrum analyzers and scanning receivers (see Clause 6) .38
Annex C (informative) Scan rates and measurement times for use with the average
detector .41
Annex D (normative) Determination of suitability of spectrum analyzers for compliance
tests.45
Bibliography .46

Figure 1 – Measurement of a combination of a CW signal (“NB”) and an impulsive
signal (“BB”) using multiple sweeps with maximum hold.18
Figure 2 – Example of a timing analysis.19
Figure 3 – A broadband spectrum measured with a stepped receiver .20
Figure 4 – Intermittent narrowband disturbances measured using fast short repetitive
sweeps with maximum hold function to obtain an overview of the emission spectrum .20

---------------------- Page: 9 ----------------------

SIST EN 55016-2-2:2011
– 4 – CISPR 16-2-2 © IEC:2010
Figure 5 – FFT scan in segments .22
Figure 6 – Frequency resolution enhanced by FFT-based measuring instrument .23
Figure 7 – Schematic drawing of the absorbing clamp measurement method .25
Figure 8 – Side view of the absorbing clamp measurement set-up for table top EUTs .28
Figure 9 – Side view of the absorbing clamp measurement set-up for floor standing
EUTs .28
Figure 10 – Process for reduction in measurement time.32
Figure C.1 – Weighting function of a 10 ms pulse for peak (“PK”) and average
detections with (“CISPR AV”) and without (“AV”) peak reading; meter time constant
160 ms.43
Figure C.2 – Weighting functions of a 10 ms pulse for peak (“PK”) and average
detections with (“CISPR AV”) and without (“AV”) peak reading; meter time constant
100 ms.43
Figure C.3 – Example of weighting functions (of a 1 Hz pulse) for peak (“PK”) and
average detections as a function of pulse width: meter time constant 160 ms.44
Figure C.4 – Example of weighting functions (of a 1 Hz pulse) for peak (“PK”) and
average detections as a function of pulse width: meter time constant 100 ms.44

Table 1 – Minimum measurement times for the four CISPR bands .16
Table 2 – Minimum scan times for the three CISPR bands with peak and quasi-peak
detectors.16
Table 3 – Sample scheme for an absorbing clamp measurement with an upper
frequency bound of 300 MHz.30
Table 4 – Sample scheme for an absorbing clamp measurement with an upper
frequency bound of 1 000 MHz .31
Table B.1 – Minimum sweep time/fastest scan rates.39
Table C.1 – Pulse suppression factors and scan rates for a 100 Hz video bandwidth.42
Table C.2 – Meter time constants and the corresponding video bandwidths and
maximum scan rates .42
Table D.1 – Maximum amplitude difference between peak and quasi-peak detected
signals .45

---------------------- Page: 10 ----------------------

SIST EN 55016-2-2:2011
CISPR 16-2-2 © IEC:2010 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
____________

SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY
MEASURING APPARATUS AND METHODS –

Part 2-2: Methods of measurement of disturbances and immunity –
Measurement of disturbance power


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard CISPR 16-2-2 has been prepared by CISPR subcommittee A: Radio-
interference measurements and statistical methods, in cooperation with CISPR subcommittee
D: Electromagnetic disturbances related to electric/electronic equipment on vehicles and
internal combustion engine powered devices.
This second edition cancels and replaces the first edition (2003), its Amendment 1 (2004) and
Amendment 2 (2005). It constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition: provisions for the use of spectrum analyzers for compliance measurements (Annex D)
and the use of FFT-based test instrumentation (Clauses 3, 6 and 8) are now included.

---------------------- Page: 11 ----------------------

SIST EN 55016-2-2:2011
– 6 – CISPR 16-2-2 © IEC:2010
It has the status of a basic EMC publication in accordance with IEC Guide 107,
Electromagnetic compatibility – Guide to the drafting of electromagnetic compatibility
publications.
The text of this standard is based on the following documents:
CDV Report on voting
CISPR/A/877/CDV CISPR/A/896/RVC

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the CISPR 16 series can be found on the IEC website under the general
title Specification for radio disturbance and immunity measuring apparatus and methods.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this publication using a colour printer.

---------------------- Page: 12 ----------------------

SIST EN 55016-2-2:2011
CISPR 16-2-2 © IEC:2010 – 7 –
SPECIFICATION FOR RADIO DISTURBANCE AND IMMUNITY
MEASURING APPARATUS AND METHODS –

Part 2-2: Methods of measurement of disturbances and immunity –
Measurement of disturbance power



1 Scope
This part of CISPR 16 specifies the methods of measurement of disturbance power using the
absorbing clamp in the frequency range 30 MHz to 1 000 MHz.
NOTE In accordance with IEC Guide 107, CISPR 16-2-2 is a basic EMC publication for use by product
committees of the IEC. As stated in Guide 107, product committees are responsible for determining the
applicability of the EMC standard. CISPR and its sub-committees are prepared to co-operate with product
committees in the determination of the value of particular EMC tests for specific products.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
CISPR 16-1-1:2010, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 1-1: Radio disturbance and immunity measuring apparatus – Measuring
ap
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.