SIST EN 60358-3:2014

Coupling capacitors and capacitor dividers - Part 3: AC or DC coupling capacitors for harmonic-filters applications

This part of IEC 60358 applies to AC or DC single-phase coupling capacitor, with rated voltage higher than 1000 V, connected line to ground with the low voltage terminal either permanently earthed or connected to a tuning device for harmonic-filters applications.

Kopplungskondensatoren und kapazitive Teiler – Teil 3: Kopplungskondensatoren für Wechsel- oder Gleichstrom als Oberwellenfilter

Condensateurs de couplage et diviseurs capacitifs - Partie 3: Condensateur de couplage à courant alternatif ou à courant continu pour des applications à filtres harmoniques

L'IEC 60358-3:2013 s'applique aux condensateurs de couplage monophasés à courant alternatif ou à courant continu, de tension assignée supérieure à 1 000 V, connectés entre la ligne et la terre, avec la borne basse tension connectée de manière permanente à la terre ou connectée à un dispositif d'accord pour des applications à filtres harmoniques. Il remplace l'Article 1 de la CEI 60358-1:2012. Mots clés: condensateurs de couplage monophasés à courant alternatif ou à courant continu

Sklopni kondenzatorji in kondenzatorski delilniki - 3. del: Sklopni kondenzatorji za izmenični ali enosmerni tok za filtre harmonskih frekvenc (IEC 60358-3:2013)

Ta del IEC 60358 velja za sklopne kondenzatorje za izmenični ali enosmerni tok z nazivno napetostjo nad 1000 V, ki so povezani s tlemi prek nizkonapetostnega terminala, ki je trajno ozemljen ali povezan z napravo za uglaševanje za filtre harmonskih frekvenc.

General Information

• Status: Published
• Publication Date: 29-May-2014
• ICS: 31.060.99 - Other capacitors
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 13-May-2014
• Due Date: 18-Jul-2014
• Completion Date: 30-May-2014
• Ref Project: EN 60358-3:2014 - Coupling capacitors and capacitor dividers - Part 3: AC or DC coupling capacitors for harmonic-filters applications

Relations

• Replaces: SIST HD 597 S1:2001 - Coupling capacitors and capacitor dividers
• Effective Date: 28-Jan-2023
• Replaces: SIST HD 597 S1:2001 - Coupling capacitors and capacitor dividers
• Effective Date: 01-Apr-2014
• Revised: SIST HD 597 S1:2001 - Coupling capacitors and capacitor dividers
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60358-3:2014
01-julij-2014
1DGRPHãþD
SIST HD 597 S1:2001
6NORSQLNRQGHQ]DWRUMLLQNRQGHQ]DWRUVNLGHOLOQLNLGHO6NORSQLNRQGHQ]DWRUML]D
L]PHQLþQLDOLHQRVPHUQLWRN]DILOWUHKDUPRQVNLKIUHNYHQF,(&
Coupling capacitors and capacitor dividers - Part 3: AC or DC coupling capacitors for
harmonic-filters applications
Ta slovenski standard je istoveten z: EN 60358-3:2014
ICS:
31.060.99 Drugi kondenzatorji Other capacitors
SIST EN 60358-3:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60358-3:2014

---------------------- Page: 2 ----------------------

SIST EN 60358-3:2014

EUROPEAN STANDARD
EN 60358-3

NORME EUROPÉENNE
March 2014
EUROPÄISCHE NORM

ICS 29.120.99; 29.240.99 Supersedes HD 597 S1:1992 (partially)


English version


Coupling capacitors and capacitor dividers -
Part 3: AC or DC coupling capacitors for harmonic-filters applications
(IEC 60358-3:2013)


Condensateurs de couplage et diviseurs Kopplungskondensatoren und kapazitive
capacitifs - Partie 3: Condensateur de Teiler – Teil 3: Kopplungskondensatoren
couplage à courant alternatif ou à courant für Wechsel- oder Gleichstrom als
continu pour des applications à filtres Oberwellenfilter
harmoniques (IEC 60358-3:2013)
(CEI 60358-3:2013)





This European Standard was approved by CENELEC on 2014-01-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2014 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60358-3:2014 E

---------------------- Page: 3 ----------------------

SIST EN 60358-3:2014
EN 60358-3:2014 - 2 -
Foreword
The text of document 33/510/CDV, future edition 1 of IEC 60358-3, prepared by IEC/TC 33, "Power
capacitors and their applications" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 60358-3:2014.

The following dates are fixed:
• latest date by which the document has (dop) 2014-10-01
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2017-01-01
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This document supersedes HD 597 S1:1992 (partially).
This European Standard is to be used in conjunction with EN 60358-1:2012 and its amendments.

This Part 3 supplements or modifies the corresponding clauses in EN 60358-1:2012.

When a particular subclause of Part 1 is not mentioned in this Part 3, that subclause applies as far as is
reasonable. Where this standard states “addition”, "modification" or “replacement”, the relevant text in
Part 1 is to be adapted accordingly.

For additional clauses, subclauses, figures, tables or annexes, the following numbering system is used:
– subclauses, tables and figures which are additional to those in Part 1 are numbered starting from 300;
– additional tables or annexes are lettered AA, BB etc.
– as the notes are integrated into the clauses, their numbering starts from 1 as usual.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 60358-3:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60633 NOTE  Harmonized as EN 60633.

---------------------- Page: 4 ----------------------

SIST EN 60358-3:2014
- 3 - EN 60358-3:2014

Annex ZA
(normative)
Normative references to i nternational publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Replace Annex ZA of EN 60358-1:2012 with the following:
Publication Year Title EN/HD Year
IEC 60060-1 2010 High-voltage test techniques - EN 60060-1 2010
Part 1: General definitions and test
requirements


IEC 60060-2 - High-voltage test techniques - EN 60060-2 -
Part 2: Measuring systems


IEC 60358-1 2012 Coupling capacitors and capacitor dividers - EN 60358-1 2012
+ corr. July 2013 Part 1: General rules + AC:2013 2013


IEC 60358-2 - Coupling capacitors and capacitor dividers - EN 60358-2 -
Part 2: AC or DC single-phase coupling
capacitor connected between line and ground
for power line carrier-frequency (PLC)
application


IEC 60481 - Coupling devices for power line carrier - -
systems


IEC 61869-5 - Instrument transformers - EN 61869-5 -
Part 5: Additional requirements for capacitor
voltage transformers

---------------------- Page: 5 ----------------------

SIST EN 60358-3:2014

---------------------- Page: 6 ----------------------

SIST EN 60358-3:2014




IEC 60358-3

®


Edition 1.0 2013-11





INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Coupling capacitors and capacitor dividers –

Part 3: AC or DC coupling capacitor for harmonic-filters applications




Condensateurs de couplage et diviseurs capacitifs –

Partie 3: Condensateur de couplage à courant alternatif ou à courant continu

pour des applications à filtres harmoniques















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX N


ICS 29.120.99; 29.240.99 ISBN 978-2-8322-1274-5



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60358-3:2014
– 2 – 60358-3 © IEC:2013
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions. 6
4 Service conditions . 7
5 Ratings . 7
6 Design requirements . 7
7 Test conditions . 7
8 Classification of tests . 7
9 Routine tests . 8
10 Type tests . 10
11 Special tests – Mechanical strength test . 11
12 Marking of the equipment . 11
Annex AA Typical diagram of a filter capacitor . 12
Annex BB (informative) High-frequency characteristics of filter capacitors . 13
Bibliography . 15

Figure 300 – Connection for voltage test of tuning device . 9
Figure AA.1 – Example of a diagram for a filter capacitor (with and without low voltage
terminal) . 12
Figure AA.2 – Example of a diagram for a filter capacitor with tuning device . 12
Figure BB.1 – Wiring diagram of the measuring circuit for the high frequency
capacitance and equivalent series resistance of a coupling capacitor . 14
Figure BB.2 – Relation between length and capacitance where capacitive deviation –
20/+50 % can be fulfilled up to 500 kHz . 14

Table 300 – Marking of the rating plate . 11

---------------------- Page: 8 ----------------------

SIST EN 60358-3:2014
60358-3 © IEC:2013 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

COUPLING CAPACITORS AND CAPACITOR DIVIDERS –

Part 3: AC or DC coupling capacitor
for harmonic-filters applications

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60358-3 has been prepared by IEC technical committee 33: Power
capacitors and their applications.
The text of this standard is based on the following documents:
CDV Report on voting
33/510/CDV 33/526/RVC

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 9 ----------------------

SIST EN 60358-3:2014
– 4 – 60358-3 © IEC:2013
A list of all parts in the IEC 60358 series, published under the general title Coupling
capacitors and capacitor dividers, can be found on the IEC website.
This standard is Part 3 of IEC 60358, published under the general title Coupling capacitor
and capacitor dividers.
This International Standard is to be used in conjunction with the latest edition of
IEC 60358-1:2012 and its amendments. It was established on the basis of the first edition
(2012) of that standard.
This Part 3 supplements or modifies the corresponding clauses in IEC 60358-1:2012.
When a particular subclause of Part 1 is not mentioned in this Part 3, that subclause applies
as far as is reasonable. When this standard states “addition”, “modification” or “replacement”,
the relevant text in Part 1 is to be adapted accordingly.
For additional clauses, subclauses, figures, tables or annexes, the following numbering
system is used:
 subclauses, tables and figures which are additional to those in Part 1 are numbered
starting from 300;
 additional tables or annexes are lettered AA, BB, etc.
 as the notes are integrated into the clauses, their numbering starts from 1 as usual.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
 reconfirmed,
 withdrawn,
 replaced by a revised edition, or
 amended.

IMPORTANT – The “colour inside” logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this publication using a
colour printer.

---------------------- Page: 10 ----------------------

SIST EN 60358-3:2014
60358-3 ©
...