IEC/SC 21A - IEC_SC_21A

IEC 63115-1:2020 specifies the marking, designation, tests and requirements for sealed nickel­metal hydride cells and batteries used in industrial applications, including stationary applications. When an IEC International Standard specifying test conditions and requirements for cells used in special applications is in conflict with this document, the former takes precedence (e.g. IEC 62675). The following are some examples of applications that utilize the cells and batteries falling under the scope of this document. • Stationary applications: telecom, uninterruptible power supplies (UPS), electrical energy storage system, utility switching, emergency power and similar applications. • Motive applications: fork-lift truck, golf cart, AGV (Automatic Guided Vehicle), railway, and marine, excluding road vehicles. Since this document covers batteries for various industrial applications, it includes those requirements that are common and minimum to the various applications. This document applies to cells and batteries. If the battery is divided into smaller units, the smaller unit can be tested as representative of the battery. The manufacturer clearly declares the tested unit. The manufacturer can add functions to the tested unit that are present in the final battery.

IEC 63057:2020 specifies safety tests and requirements for secondary lithium batteries permanently installed in road vehicles not for the propulsion. Replacement secondary batteries permanently installed in road vehicles not for propulsion are covered by this document. The following are typical applications that utilize the batteries under the scope of this document: a power source for the starting of internal combustion engines, lighting, on-board auxiliary equipment, and energy absorption for regeneration from braking. This document applies to batteries with a maximum voltage less than or equal to 60 V DC. The batteries primarily used for propulsion of electric vehicles (EVs), including battery electric vehicles (BEVs), hybrid electric vehicles (HEVs), and plug-in hybrid electric vehicles (PHEVs) are not covered by this document.

IEC 61951-2:2011 specifies marking, designation, dimensions, tests and requirements for portable sealed nickel-metal hydride, small prismatic, cylindrical and button rechargeable single cells, suitable for use in any orientation. This third edition cancels and replaces the second edition published in 2003 of which it constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - clause 4: addition of 2 parameters; - clause 5: addition of cells type 'S' and cells type 'T'; - subclause 6.1.2: addition of new cylindrical cells; - subclause 7.8: addition of a specific test for 'S' cells.

IEC 62619:2017 specifies requirements and tests for the safe operation of secondary lithium cells and batteries used in industrial applications including stationary applications. When there exists an IEC standard specifying test conditions and requirements for cells used in special applications and which is in conflict with this document, the former takes precedence (e.g., IEC 62660 series on road vehicles). The following are some examples of applications that utilize cells and batteries under the scope of this document. - Stationary applications: telecom, uninterruptible power supplies (UPS), electrical energy storage system, utility switching, emergency power, and similar applications. - Motive applications: forklift truck, golf cart, auto guided vehicle (AGV), railway, and marine, excluding road vehicles. Since this document covers batteries for various industrial applications, it includes those requirements, which are common and minimum to the various applications. Electrical safety is included only as a part of the risk analysis of Clause 8. In regard to details for addressing electrical safety, the end use application standard requirements have to be considered. This document applies to cells and batteries. If the battery is divided into smaller units, the smaller unit can be tested as the representative of the battery. The manufacturer clearly declares the tested unit. The manufacturer may add functions, which are present in the final battery to the tested unit.

IEC 61951-1:2013 specifies marking, designation, dimensions, tests and requirements for portable sealed nickel-cadmium small prismatic, cylindrical and button rechargeable single cells, suitable for use in any orientation. This third edition cancels and replaces the second edition (2003) and its amendment 1 (2005) of which it constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - addition of several new cell sizes; - introduction of a new cell type J; - creation of Annex A (informative): Capacity of batteries measurement.

IEC 61960-3:2017 specifies performance tests, designations, markings, dimensions and other requirements for secondary lithium single cells and batteries for portable applications. The objective of this document is to provide the purchasers and users of secondary lithium cells and batteries with a set of criteria with which they can judge the performance of secondary lithium cells and batteries offered by various manufacturers. Portable applications comprise hand-held equipment, transportable equipment and movable equipment. This first edition cancels and replaces the second edition of IEC 61960 published in 2011. It is a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - adding definition of portable applications (Scope), - update of examples of cells (Table 1 and 2), - adding “Dimensions of the cell with a laminate film case” (Annex A), - adding “Capacity after storage” (from the date of manufacture) (Annex B).

IEC 62133-2:2017 specifies requirements and tests for the safe operation of portable sealed secondary lithium cells and batteries containing non-acid electrolyte, under intended use and reasonably foreseeable misuse. This first edition cancels and replaces the second edition of IEC 62133 published in 2012. It constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 62133:2012: - separation of nickel systems into a separate Part 1; - inclusion of coin cell requirements; - update of assembly of cells into batteries (5.6); - mechanical tests [vibration, shock] (7.3.8.1, 7.3.8.2); - insertion of IEC TR 62914 within the Bibliography. Key words: lithium, li-ion

IEC 62133-1:2017 specifies requirements and tests for the safe operation of portable sealed secondary nickel cells and batteries containing alkaline electrolyte, under intended use and reasonably foreseeable misuse. This first edition cancels and replaces the second edition of IEC 62133 published in 2012. It constitutes a technical revision. This edition includes the following significant technical changes with respect to IEC 62133:2012: - separation of lithium systems into a separate Part 2; - inclusion of button cell requirements.

NEW!IEC 60623:2017 is available as IEC 60623:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60623:2017 specifies marking, designation, dimensions, tests and requirements for vented nickel-cadmium prismatic secondary single cells. When there exists an IEC standard specifying test conditions and requirements for cells used in special applications and which is in conflict with this document, the former takes precedence. This edition includes the following significant technical changes with respect to the previous edition: - optional characterization of cells designed for performances at very low and/or very high temperature; - optional characterization of cells tested with CCCV charge; - optional characterization of cells designed for rapid charge; - optional characterization of cells designed for high cycling.

IEC 62620:2014 specifies marking, tests and requirements for lithium secondary cells and batteries used in industrial applications including stationary applications. When there exists an IEC standard specifying test conditions and requirements for cells used in special applications and which is in conflict with this standard, the former takes precedence. (e.g. IEC 62660 series on road vehicles). The following are some examples of applications that utilize the cells and batteries under the scope of this standard. - Stationary applications: telecom, uninterruptible power supplies (UPS), electrical energy storage system, utility switching, emergency power and similar applications. - Motive applications: fork-lift truck, golf cart, AGV, railway, and marine, excluding road vehicles. This standard applies to cells and batteries. If the battery is divided into smaller units, the smaller unit can be tested as the representative of the battery. The manufacturer clearly declares the tested unit. The manufacturer may add functions, which are present in the final battery, to the tested unit.

IEC 62675:2014 specifies marking, designation, dimensions, tests and requirements for sealed nickel-metal hydride prismatic secondary single cells.

IEC 61960-4:2020 specifies performance tests, designations, markings, dimensions and other requirements for coin secondary lithium cells and batteries for portable applications and backup power supply such as memory backup applications. The objective of this document is to provide the purchasers and users of coin secondary lithium cells and batteries with a set of criteria with which they can assess the performance of coin secondary lithium cells and batteries offered by various manufacturers. This document defines a minimum required level of performance and a standardized methodology by which testing is performed and the results of this testing reported to the user. Hence, users will be able to establish the viability of commercially available cells and batteries via the declared specification and thus be able to select the cell or battery best suited for their intended application. This document covers coin secondary lithium cells and batteries with a range of chemistries. Each electrochemical couple has a characteristic voltage range over which, during discharge, it releases its electrical capacity, a characteristic nominal voltage and a characteristic end-of-discharge voltage. Users of coin secondary lithium cells and batteries are requested to consult the manufacturer for advice. This document also provides guidelines for designers of equipment using lithium batteries.

IEC 63056:2020 specifies requirements and tests for the product safety of secondary lithium cells and batteries used in electrical energy storage systems (Figure 2) with a maximum DC voltage of 1 500 V (nominal). Basic safety requirements for the secondary lithium cells and batteries used in industrial applications are included in IEC 62619. This document provides additional or specific requirements for electrical energy storage systems. Since this document covers batteries for various electrical energy storage systems, it includes those requirements which are common and minimum to the electrical energy storage systems. Examples of appliances that are within the scope of this document are: • telecommunications, • central emergency lighting and alarm systems, • stationary engine starting, • photovoltaic systems, • home (residential) energy storage systems (HESS), and • large energy storage: on-grid/off-grid. This document applies to cells and batteries for uninterruptible power supplies (UPS). This document does not apply to portable systems 500 Wh or below, which are covered by IEC 61960-3.

IEC-63115-2:2021 specifies designations, tests and requirements for the safe operation of sealed nickel-metal hydride cells and batteries used in industrial applications excluding road vehicles. Since this document covers batteries for various industrial applications, it includes those requirements which are common and minimum to the various applications.

This International standard specifies tests and requirements for verifying the mechanical behaviour of sealed portable secondary cells and batteries during handling and normal use

This International Standard specifies marking, designation, dimensions, tests and require-ments for vented nickel-cadmium prismatic secondary single cells where special provisions have been made in order to have partial or, under very specific conditions, full gas recombination.

Specifies tests and requirements for sealed nickel-cadmium prismatic rechargeable single cells.

Applies to electrolytes and their components when used in vented nickel-cadmium cells.

Applies to secondary cells and batteries containing alkaline or other non-acid electrolytes. It proposes a mathematically correct method of current designation which shall be used in future secondary cell and battery standards.

IEC 61951-1:2013 specifies marking, designation, dimensions, tests and requirements for portable sealed nickel-cadmium small prismatic, cylindrical and button rechargeable single cells, suitable for use in any orientation. This third edition cancels and replaces the second edition (2003) and its amendment 1 (2005) of which it constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - addition of several new cell sizes; - introduction of a new cell type J; - creation of Annex A (informative): Capacity of batteries measurement.

IEC 62133:2012 specifies requirements and tests for the safe operation of portable sealed secondary cells and batteries (other than button) containing alkaline or other non-acid electrolyte, under intended use and reasonably foreseeable misuse. This edition includes the following significant technical changes with respect to the previous edition: - update of assembly of cells into batteries (5.5); - addition of design recommendations for lithium system only (5.6.2); - separation of nickel systems and lithium systems (Clause 6); - addition of specific requirements and tests for lithium systems (Clause 8); - addition of charging of secondary lithium-ion cells for safe use (Annex A).

IEC 61960:2011 specifies performance tests, designations, markings, dimensions and other requirements for secondary lithium single cells and batteries for portable applications. The objective of this standard is to provide the purchasers and users of secondary lithium cells and batteries with a set of criteria with which they can judge the performance of secondary lithium cells and batteries offered by various manufacturers. This second edition cancels and replaces the first edition published in 2003. It is a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - 7.6 Endurance in cycles: addition of an accelerated test procedure.

IEC 61951-2:2011 specifies marking, designation, dimensions, tests and requirements for portable sealed nickel-metal hydride, small prismatic, cylindrical and button rechargeable single cells, suitable for use in any orientation. This third edition cancels and replaces the second edition published in 2003 of which it constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - clause 4: addition of 2 parameters; - clause 5: addition of cells type 'S' and cells type 'T'; - subclause 6.1.2: addition of new cylindrical cells; - subclause 7.8: addition of a specific test for 'S' cells.

Specifies tests and requirements for sealed nickel-cadmium rechargeable monobloc batteries in button cell design, suitable for use in any orientation.

This International Standard specifies performance tests, designations, markings, dimensions and other requirements for secondary lithium single cells and batteries for portable applications. The objective of this standard is to provide the purchasers and users of secondary lithium cells and batteries with a set of criteria with which they can judge the performance of secondary lithium cells and batteries offered by various manufacturers.

This part of EN 61951 specifies marking, designation, dimensions, tests and require-ments for portable sealed nickel-metal hydride, small prismatic, cylindrical and button rechargeable single cells, suitable for use in any orientation

This part of EN 61951 specifies marking, designation, dimensions, tests and requirements for portable sealed nickel-cadmium small prismatic, cylindrical and button rechargeable single cells, suitable for use in any orientation.

This International Standard specifies requirements and tests for the safe operation of portable sealed secondary cells and batteries (other than button) containing alkaline or other non-acid electrolyte, under intended use and reasonably foreseeable misuse.

Specifies tests and requirements for vented nickel-cadmium prismatic secondary single cells.

This International Standard specifies performance and safety tests, designations, markings, dimensions and other requirements for secondary lithium batteries. The objective of this standard is to provide the purchasers and users of secondary lithium batteries with a set of criteria with which they can judge the performance and safety of various secondary lithium batteries offered by various manufacturers. This standard defines a minimum required level of performance and safety, and a standardized methodology by which testing is performed and the results of this testing reported to the user. Hence, users will be able to establish the viability of commercially available batteries via the declared specification and thus be able to select the battery best suited for their intended application.

specifies marking, designation, dimensions, tests and requirements for portable sealed nickel-metal hydride, small prismatic, cylindrical and button rechargeable single cells, suitable for use in any orientation. This International Standard is an amalgamation of all currently valid standards for portable sealed nickel-metal hydride secondary single cells: EN 61436, 1998 and EN 61808 , 1999. It complies with the objective to reduce the number of valid standards, and does not introduce technical modifications in the original standards. If, in the future, this standard is amended, the relevant original standards will be cancelled.

specifies marking, designation, dimensions, tests and requirements for portable sealed nickel-cadmium small prismatic, cylindrical and button rechargeable single cells, suitable for use in any orientation. This International Standard is an amalgamation of all currently valid standards for portable sealed nickel-cadmium secondary single cells: EN 60285, 1999, EN 60509, 1988 and EN 61440, 1997. It complies with the objective, which was to reduce the number of valid standards.

This International Standard specifies performance and safety tests, designations, markings, dimensions and other requirements for secondary lithium single cells. The objective of this standard is to provide the purchasers of secondary lithium cells with a set of criteria with which they can judge the performance and safety of various secondary lithium cells offered by various manufacturers.

Specifies tests and requirements for portable sealed alakline secondary cells and batteries (other than button) for their safe operation under intended use and reasonably foreseable misuse.

Specifies tests and requirements for sealed nickel-metal hydride button rechargeable single cells, suitable for use in any orientation.

EN following parallel vote * Superseded by EN 61951-1:2003

Specifies tests and requirements for sealed nickel-metal hydride rechargeable single cells, suitable for use in any orientation.

Specifies marking, designation, dimensions, tests and requirements for sealed nickel-cadmium small prismatic rechargeable single cells, suitable for use in any orientation.

Specifies tests and requirements for vented nickel-cadmium prismatic secondary single cells.

Specifies tests and requirements for sealed nickel-cadmium prismatic rechargeable single cells.

EN following parallel vote * Superseded by EN 61951-1:2003

Specifies tests and requirements for sealed nickel-cadmium cylindrical rechargeable single cells, suitable for use in any orientation. Specific tests and requirements for cells intended for use in permanent charge at elevated temperatures are also included.

Applies to electrolytes and their components when used in vented nickel-cadmium cells.

Specifies tests and requirements for sealed nickel-cadmium rechargeable single button cells, suitable for use in any position