IEC 62841-3-12:2017 applies to transportable threading machines. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. This Part 3-12 is to be used in conjunction with the first edition of IEC 62841-1:2014. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 4231:2016 is a supplement to ISO 2568 and ISO 4230 and specifies the dimensions of hand- and machine-operated circular screwing dies intended for production of parallel pipe threads, G series, in accordance with ISO 228‑1.
The general dimensions of these dies (diameter, thickness and fixing dimensions) are in accordance with ISO 2568 so as to permit the driving of hand-operated dies with the aid of the die stocks defined in that document.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 4230:2016 is a supplement to ISO 2568 and ISO 4231 and specifies the dimensions of hand- and machine-operated circular screwing dies intended for production of taper pipe threads, R series, in accordance with ISO 7‑1.
With the exception of the die 1/16, the general dimensions of these dies (diameter, thickness and fixing dimensions) are in accordance with ISO 2568 so as to permit the driving of hand-operated dies with the aid of the die stocks defined in that document.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 529:2017 specifies the general dimensions of short machine taps and hand taps. These dimensions, established as functions of the thread diameter and pitch, are the following: - length of thread (maximum); - overall length; - shank diameter and dimensions of driving square; - dimensions of the connecting portion between the shank and threaded part. ISO 529:2017 is applicable to taps intended for cutting the following threads: a) ISO metric threads: - coarse pitch; - fine pitch; b) ISO inch threads: - "Unified Coarse" series (UNC) and "Unified Fine" series (UNF); c) Inch threads, non-recommended: - "British Standard Whitworth" (BSW) and "British Standard Fine" (BSF); - "British Association" (BA). NOTE 1 The overall length, thread length and diameters of shank for taps whose thread diameter and pitch are not listed in tables are given in Table A.1. NOTE 2 Annex B gives an abstract from ISO 237 for shank diameters and size of driving squares, for information. NOTE 3 Technical specifications for taps covered by this document (including marking) are given in ISO 8830.

  • Standard
    26 pages
    English language
    sale 15% off
  • Standard
    26 pages
    English language
    sale 15% off
  • Standard
    26 pages
    French language
    sale 15% off
  • Standard
    26 pages
    French language
    sale 15% off

ISO 2284:2017 specifies the general dimensions and marking of hand taps for pipe threads. It is applicable to the two following types of tap: - taps for parallel threads (see Figure 1 and Table 1), - taps for taper threads (see Figure 2 and Table 2), having threads in accordance with ISO 7‑1 and ISO 228‑1. Furthermore, it gives in Annex A the bases used for calculation of the dimensions, and in Annex B the relationship between designations in this document and the ISO 13399 series.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off

This International Standard is a supplement to ISO 2568 and ISO 4230 and specifies the dimensions of
hand- and machine-operated circular screwing dies intended for production of parallel pipe threads,
G series, in accordance with ISO 228-1.
The general dimensions of these dies (diameter, thickness and fixing dimensions) are in accordance
with ISO 2568 so as to permit the driving of hand-operated dies with the aid of the die stocks defined in
that document.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard is a supplement to ISO 2568 and ISO 4231 and specifies the dimensions
of hand- and machine-operated circular screwing dies intended for production of taper pipe threads,
R series, in accordance with ISO 7-1.
With the exception of the die 1/16, the general dimensions of these dies (diameter, thickness and fixing
dimensions) are in accordance with ISO 2568 so as to permit the driving of hand-operated dies with the
aid of the die stocks defined in that document.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 4231:2016 is a supplement to ISO 2568 and ISO 4230 and specifies the dimensions of hand- and machine-operated circular screwing dies intended for production of parallel pipe threads, G series, in accordance with ISO 228‑1. The general dimensions of these dies (diameter, thickness and fixing dimensions) are in accordance with ISO 2568 so as to permit the driving of hand-operated dies with the aid of the die stocks defined in that document.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

ISO 4230:2016 is a supplement to ISO 2568 and ISO 4231 and specifies the dimensions of hand- and machine-operated circular screwing dies intended for production of taper pipe threads, R series, in accordance with ISO 7‑1. With the exception of the die 1/16, the general dimensions of these dies (diameter, thickness and fixing dimensions) are in accordance with ISO 2568 so as to permit the driving of hand-operated dies with the aid of the die stocks defined in that document.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

ISO 8051:2016 specifies the dimensions for full-diameter shank taps with recess with nominal diameters from M3 to M10 and thus complements ISO 2283, which concerns relieved shank taps. It applies to long shank machine taps. Technical specifications for taps covered by ISO 8051:2016 (including marking) are given in ISO 8830.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

IEC 61029-2-12:2010 applies to machines for creating external threads that either rotate the work piece or the cutting head.

  • Standard
    25 pages
    English and French language
    sale 15% off

Is valid for the short taps specified in ISO 529 as well as for any other kind of ground thread taps with the same diameters and pitches. The internal threads produced with those taps are conventionally designated by the simplified denomination of "nut" in agreement with the word used in ISO 965 for the general designation of all internal threads.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Specifies how to prepare detail specifications for power
transformers. Includes a blank detail specification, which shows
the format, and indicates which tests are considered to be
appropriate to this type of component.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Gives terms in the three official languages of ISO (English, French and Russian) and in addition to these the equivalent terms in German and Italian. ISO 5967 serves as a reference for tap users and manufacturers. The diagramms given, however, are only to illustrate the terminilogy as tap design can vary according to the manufacturer. Includes nomenclature of the main types of taps,styles of threaded portion, sets of taps, dimansional charcteristics and thread profiles.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off

Describes material and hardness, cutting geometry, run-out tolerances, and the marking. Applies to standard taps in accordance with ISO 529, ISO 2283, ISO 2284, and ISO 2857.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Gives terms in the three official languages of ISO (English, French and Russian) and in addition to these the equivalent terms in German and Italian. ISO 5967 serves as a reference for tap users and manufacturers. The diagramms given, however, are only to illustrate the terminilogy as tap design can vary according to the manufacturer. Includes nomenclature of the main types of taps,styles of threaded portion, sets of taps, dimansional charcteristics and thread profiles.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Specifies how to prepare detail specifications for power
transformers. Includes a blank detail specification, which shows
the format, and indicates which tests are considered to be
appropriate to this type of component.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Is valid for the short taps specified in ISO 529 as well as for any other kind of ground thread taps with the same diameters and pitches. The internal threads produced with those taps are conventionally designated by the simplified denomination of "nut" in agreement with the word used in ISO 965 for the general designation of all internal threads.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off
  • Standard
    11 pages
    French language
    sale 15% off

This second edition cancels and replaces the first edition (ISO 7226:1985), of which it constitutes a minor revision. Specifies the general dimensions of hexagonal for certain suze ofISO metric threads, ISO inch threads and pipe threads, as well as the non-preferred thread series BSW, BSF and BA. Gives the marking of these dienuts.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    3 pages
    French language
    sale 15% off
  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English, French and Russian language
    sale 15% off

Gives terms in the three official languages of ISO (English, French and Russian) and in addition to these the equivalent terms in German and Italian. ISO 5967 serves as a reference for tap users and manufacturers. The diagramms given, however, are only to illustrate the terminilogy as tap design can vary according to the manufacturer. Includes nomenclature of the main types of taps,styles of threaded portion, sets of taps, dimansional charcteristics and thread profiles.

  • Standard
    26 pages
    English language
    sale 15% off

Specifies the deviations and tolerances on the major diameter and the pitch diameter together with the limits of these diameters for ground thread taps intended for production of these pipe threads acoording to ISO 228-1 and ISO 7-1 respectively. the internal threads produced with the ground thread taps are conventionally designated by the simplified denomination od "nut".

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off
  • Standard
    7 pages
    French language
    sale 15% off

Gives the terminology of the designs of hardmetal heading dies (see table 1) and heading and extruding dies (see table 2) as well as the symbols and corresponding terms for the principal dimensions used for description of these tools (see table 3). In addition to the terms in two of the three official ISO languages (English and French), ISO 5396 gives the equivalent terms in German, Italian, Swedish and Dutch.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English and French language
    sale 15% off

Is valid for the short taps specified in ISO 529 as well as for any other kind of ground thread taps with the same diameters and pitches. The internal threads produced with those taps are conventionally designated by the simplified denomination of "nut" in agreement with the word used in ISO 965 for the general designation of all internal threads.

  • Standard
    13 pages
    English language
    sale 15% off
  • Standard
    13 pages
    French language
    sale 15% off
  • Standard
    13 pages
    French language
    sale 15% off

IEC 62841-2-9:2015 applies to hand-held tappers and threaders. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools is given in Annex K. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3. The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.
Key words: Tapper, Threader, Internal Screw Threads, External Screw Threads
This publication is to be read in conjunction with

  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Deals with the safety of hand-held motor-operated or  magnetically driven tools, specific requirements for tappers.  The rated voltage being not more than 250 V for single-phase  a.c. or d.c. and 440 V for three-phase a.c. tools.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This secind edition cancels and replaces the first edition (ISO 4231:1977). Is a supplement to ISO 2568 and ISO 4230 and lys down the diemensions of these screwing dies intended for production of parallel pipe threads in accordance with ISO 228-1. Diameter, thickness and fixing dimensions are accordance with ISO 2568 so as to permit the driving of and-oprated dies with the aid of the die stocks defined in that document.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This secind edition cancels and replaces the first edition (ISO 4231:1977). Is a supplement to ISO 2568 and ISO 4230 and lys down the diemensions of these screwing dies intended for production of parallel pipe threads in accordance with ISO 228-1. Diameter, thickness and fixing dimensions are accordance with ISO 2568 so as to permit the driving of and-oprated dies with the aid of the die stocks defined in that document.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This second edition cancels and replaces the first edition (ISO 4230:1977). Is a supplement to ISO 2568 and ISO 4231 and lys down the dimensions of these screwing dies intended for production of taper pipe threads in accordance with ISO 7-1. With the exception of the die 1/16, the diameter, thickness and fixing dimensions are in accordance with ISO 2568 so as to permit the driving of hand-operated dies with the aid of the die stocks defined in that document.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This second edition cancels and replaces the first edition (ISO 4230:1977). Is a supplement to ISO 2568 and ISO 4231 and lys down the dimensions of these screwing dies intended for production of taper pipe threads in accordance with ISO 7-1. With the exception of the die 1/16, the diameter, thickness and fixing dimensions are in accordance with ISO 2568 so as to permit the driving of hand-operated dies with the aid of the die stocks defined in that document.

  • Standard
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61029-2-12:2010 applies to machines for creating external threads that either rotate the work piece or the cutting head.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Deals with the safety of hand-held motor-operated or magnetically driven tools, specific requirements for tappers. The rated voltage being not more than 250 V for single-phase a.c. or d.c., and 440 V for three-phase a.c.tools.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Superseded by EN 60745-2-9:2009

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

To be ratified as EN 60745-2-9:2003/A11:200X

  • Amendment
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This clause of Part 1 is applicable except as follows:     1.1 Addition: This standard applies to tappers.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    French language
    sale 15% off

This clause of Part 1 is applicable except as follows: 1.1 Addition: This standard applies to tappers.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Superseded by EN 50144-2-9:1996

  • Standardization document
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Specifies the general dimensions: length of thread (maximum), overall length, shank diameter and dimensions of driving square, dimensions of the connecting portion between the shank and threaded part. Applies to taps intended for cutting the following threads: ISO metric threads (coarse and fine pitch), ISO inch threads ("Unified Coarse" series (UNC) and "Unified Fine" series (UNF)), and non-recommended inch threads ("British Standard Whitworth" (BSW) and "British Standard Fine" (BSF), "British Association" (BA)).

  • Standard
    25 pages
    English language
    sale 15% off
  • Standard
    25 pages
    French language
    sale 15% off
  • Standard
    25 pages
    French language
    sale 15% off