ISO/TC 41 - Pulleys and belts (including veebelts)

This document specifies the principal dimensional characteristics of V-ribbed pulley groove profiles, together with the corresponding endless V-ribbed belts of PK profile which are used predominantly for automotive accessory drive applications. This document does not apply to the complete array of V-ribbed belts and pulleys of PH, PJ, PK, PL and PM profile for industrial and other non-automotive applications which are covered by ISO 9982. PK belt profile dimensions and tolerances are the same in both International Standards. 6.2 and 6.3 of this document do not apply to elastic belts.

This document specifies the requirements for belts and pulleys for V-belt drives used for driving auxiliaries of internal combustion engines for the automotive industry.

This document specifies test methods for determining the electrical resistances of light conveyor belts according to ISO 21183‑1. The resistances are surface resistance, volume resistance perpendicular to the belt plane, and longitudinal and transverse volume resistance parallel to the belt plane. This document also specifies two test methods for determining the surface resistivity and the volume resistivity.

This document specifies the characteristics of synchronous endless belts and their related pulleys for use in automotive applications such as engine camshaft drives. The characteristics include: — belt pitch spacing; — belt nominal tooth dimensions; — belt width and width tolerance; — belt pitch length and pitch length tolerance; — pulley groove dimensions and tolerances; — pulley tolerances and quality specifications. Test methods for measuring belt pitch length and lateral runout are also included.

This document specifies the limiting values for the adjustment of centres of two transmission pulleys. It is applicable to: — crowned pulleys for flat belts; — grooved pulleys for V-belts, either single, multiple or joined; — grooved pulleys for V-ribbed belts; — toothed pulleys for synchronous belts.

This document establishes a list of equivalent terms relating to light conveyor belts. NOTE In addition to terms used in the three official ISO languages (English, French and Russian), this document gives the equivalent terms in German, Spanish, Italian and Japanese; these are published under the responsibility of the member bodies for Germany (DIN), Spain (AENOR), Italy (UNI) and Japanese (JISC). However, only the terms given in the official languages can be considered as ISO terms.

This document specifies the main dimensions of endless hexagonal belts intended for use on agricultural machinery (and, in particular, harvester-thresher machines), together with the groove section of the corresponding fixed-diameter pulleys.

This document specifies three methods for the measurement of total belt thickness and the thickness of covers of steel cord conveyor belts. Methods A1 and A2 (micrometer methods) can be used for all steel cord conveyor belts for the measurement of both total belt thickness and cover thickness. Method B (optical method) is intended for the measurement of cover thickness only. It is not suitable if there is a textile or metal weft, nor if the ends of the steel cords become twisted when cut.

ISO 20238:2018 specifies a method of testing to determine the propensity of a conveyor belt to generate heat flame or glow when held stationary, under a given tension, in surface contact around a rotating driven steel drum. ISO 20238:2018 describes means of varying the conveyor belt tension. NOTE For conveyor belts containing steel reinforcement, it may not be possible to conduct this test in full due to the inability of the conveyor belt to comply with the requirements of 7.2. In this case, premature termination according to 7.3 can be necessary.

ISO 5288:2017 specifies the terms and definitions related to the use of synchronous belt drives for mechanical power transmission and where positive indexing or synchronization is required.

ISO 17396:2017 specifies the principal characteristics of synchronous endless and open belts and pulleys of the profile systems T and AT for use in synchronous belt drives for mechanical power transmission and where positive indexing or synchronization can be required. NOTE Synchronous belt drives have been known by various titles in the past: for example, timing belt drives, positive belt drives, gear belt drives. The principal belt and pulley characteristics include a) nominal belt tooth dimensions, b) belt tooth pitch spacing, c) belt length and width dimensions, d) belt length measurement specifications, e) pulley groove dimensions and tolerances, f) pulley diameter and width dimensions and tolerances, and g) pulley quality specification. The belts of the profile systems T and AT are made of polyurethane with high-tension fine steel cord tension members in most cases. As far as certain forces are given in this document, these values are only valid for these kinds of belt. For polyurethane belts with different tensile cords, i.e. aramid or rubber belts reinforced with glass fibre, the values can be different. It is intended that the user and the manufacturer agree about suitable values. Open belts made of thermoplastic polyurethane can be spliced to work as endless belts in conveyor applications. In this case, the tolerances are not valid for the splicing area of the endless spliced belt.

ISO 433:2017 specifies the marking of conveyor belts, i.e. - the indications to be marked; - the dimensions of the marks; - the position of the marks. ISO 433:2017 does not apply to light conveyor belts as described in ISO 21183‑1.

ISO 505:2017 specifies a method of test for the measurement of the propagation resistance of an initial tear in textile conveyor belts, either in full thickness or of the carcass only. This test is intended for application to textile belts in installations where there is a risk of longitudinal tearing.

ISO 5295:2017 establishes formulae for the calculation of power rating and centre distance of standard synchronous belts on two pulley drives. It is applicable to trapezoidal belts only. It does not apply to curvilinear synchronous belts. The numerical values of certain parameters used in the calculations depend upon the pitch and the construction of the belt and are specified by the belt manufacturer.

ISO 15236-3:2017 specifies the performance and constructional requirements applicable to conveyor belts for underground mining having steel cords in the longitudinal direction as reinforcement. The requirements for design and construction apply to the design of single belts, as well as the design of complete type series such as those covered in ISO 15236‑2. Steel cord belts in accordance with this document are intended for use underground in coal mines and in other applications where the highest demands for safety against fire and explosion hazards have to be complied with. NOTE At present, the requirements can only be met by the use of compounds based on chloroprene rubber for the covers, as well as for the bonding rubber.

ISO 15236-2:2017 specifies preferred types of conveyor belts with steel cords in the longitudinal direction as reinforcement. The belt type series in this document are based on the general requirements for construction given in ISO 15236‑1.

ISO 703:2017 specifies a test method for determining the transverse flexibility (troughability) of a conveyor belt, expressed as a ratio, F/L. The method is not suitable or valid for light conveyor belts as described in ISO 21183‑1.

ISO 15236-1:2016 specifies the performance and constructional requirements applicable to conveyor belts having steel cords in the longitudinal direction as reinforcement. The requirements for construction given in Clause 6 apply to the design of single belts, as well as the design of complete type series such as those covered in ISO 15236‑2.

ISO 9856:2016 specifies a method for determining the elastic and permanent elongation of a conveyor belt and the calculation of the elastic modulus. It is not applicable or valid for light conveyor belts as described in ISO 21183‑1.

ISO 283:2015 specifies a test method for the determination of the full thickness tensile strength in the longitudinal direction and the elongation at the reference force and breaking point of conveyor belts having a textile carcass. The method can also be used for the determination of full thickness tensile strength in the transverse direction and the elongation at the breaking point, for use when the manufacturer is requested by the purchaser to state values for these properties. ISO 283:2015 is not suitable or valid for light conveyor belts as described in ISO 21183‑1.

ISO 7622-2:2015 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts. It applies exclusively to conveyor belts with a steel carcass. NOTE A method for the determination of elongation is specified in ISO 7622‑1.

ISO 7623:2015 specifies a method for determining the bond strength of metal cords to their surrounding coating, either in the initial state or after thermal treatment. It applies exclusively to metal-carcass conveyor belts.

ISO 19347:2015 specifies the principal characteristics of synchronous endless belts and pulleys for use in synchronous endless belt drives[1] for mechanical power transmission and where positive indexing or synchronization is required. The principal characteristics includes the following: a) belt nominal tooth dimensions; b) belt length and width dimensions and tolerances; c) belt length-measurement specifications; d) pulley grooves dimensions and tolerances; e) pulley dimensions and tolerances; f) pulley quality specification. [1] These drives have been known under various names in the past, for example: timing belt drives, positive belt drives, gear belt drives.

ISO 9563:2015 specifies the maximum and minimum electrical resistance of antistatic endless and open ended synchronous belts. This International Standard provides guidelines to allow testing of synchronous belts to prove their static conductive (dissipative) properties as well as a corresponding production control test method. The application of this International Standard is limited to new belts intended to be used in an explosive atmosphere or in situations where there is a fire risk. The test is intended to ensure that the belt is sufficiently conductive to dissipate charges of electricity which may form on it in service. In the case of a production control test, the decision is left to national standards or agreement between interested parties as to whether the test shall be carried out on each belt in a batch or on only a percentage of belts in a batch. For each proof test, the belt manufacturer shall determine which type of electrode and conductive coating material shall be used.

ISO 13050:2014 specifies the principal characteristics of metric pitch curvilinear synchronous endless belts and pulleys in G, H, R, and S profile systems for use in synchronous belt drives (also known in the past as timing belt drives, positive belt drives, gear belt drives) for mechanical power transmission and where positive indexing or synchronization might be required. The principal belt and pulley characteristics include the following: nominal belt tooth dimensions; belt tooth pitch spacing; belt length and width dimensions and tolerances; belt length measurement specifications; pulley groove dimensions and tolerances; pulley diameter and width dimensions and tolerances; pulley quality specification.

ISO 24035:2014 provides dimensional details of the V-drive belts used on agricultural machinery. It is intended to reflect practice in the design of such drives and to provide, where practicable, links to International Standards for similar belts used on industrial machinery.

ISO 1813:2014 specifies the maximum electrical resistance of antistatic endless V-ribbed belts, joined V-belts, and single V-belts including wide section belts and hexagonal belts, as well as corresponding production control and individual proof methods of measurements. The application of ISO 1813:2014 is limited to new belts intended to be used in an explosive atmosphere or in situations where there is a fire risk. The test is intended to ensure that the belt is sufficiently conductive to dissipate charges of electricity which can form on it in service.

ISO 11749:2014 specifies a dynamic test method for the quality control of V-ribbed belts (PK profile) which are used predominantly for accessory drive applications in the automotive industry.

ISO 1081:2013 specifies the terms and definitions, in English and French, relating to V-belt drives, V-belts, hexagonal belts, joined V-belts and the corresponding V-grooved pulleys, V-ribbed belt drives, V-ribbed belts and V-ribbed pulleys, as well as the corresponding symbols.The general definitions are valid irrespective of the system describing the pulleys. The dimensions of pulley grooves can be defined either on the basis of the datum width or on the basis of the effective width. As a result, two systems for the definition and description of the dimensions of pulleys and belts have been developed. The two systems are independent of each other.

ISO 8094:2013 specifies a test method for determining the adhesion strength of the cover to the core layer. It applies exclusively to steel cord conveyor belts.

ISO 7622-1:2013 specifies a method for the determination of the elongation of steel cords constituting the carcass of conveyor belts, when subjected to a force corresponding to 10 % and 60 % of the specified tensile strength. It applies exclusively to conveyor belts with a steel carcass.

ISO 340:2013 specifies a method for assessing, on a small scale, the reaction of a conveyor belt to an ignition flame source. It is applicable to conveyor belts having a textile carcass as well as steel cord conveyor belts.

ISO 21179:2013 specifies a test method for the determination of the electrostatic field generated by a running light conveyor belt according to ISO 21183-1.

ISo 21181:2013 specifies a test method for the determination of the relaxed elastic modulus of light conveyor belts according to ISO 21183-1 or other conveyor belts where ISO 9856 is not applicable.

ISO 21182:2013 specifies test methods for determining the dynamic and static coefficients of friction for light conveyor belts according to ISO 21183-1.

ISO 14890:2013 specifies requirements for rubber and/or plastics covered conveyor belting of textile construction for general surface use on flat or troughed idlers. ISO 14890:2013 is not suitable or valid for light conveyor belts as described in ISO 21183-1. Items that are not requirements of ISO 14890:2013, but need to be agreed between the manufacturer and the purchaser, as well as a list of the details intended to be supplied by the purchaser of belting with an enquiry are included in the annexes.

ISO 284:2012 specifies the maximum electrical resistance of a conveyor belt and the corresponding test method. The test is intended to ensure that the belt is sufficiently conductive to avoid the accumulation of electrical static charge which can be developed during service use. ISO 284:2012 is not suitable or applicable to light conveyor belts as described in ISO 21183-1, the static electrical properties of which are measured by ISO 21178.

ISO 16851:2012 specifies a method for determining the net length of an endless (spliced) conveyor belt. It applies to all types of construction of conveyor belting with the exception of belts containing steel cord reinforcement. It is not suitable or valid for light conveyor belts described in ISO 21183-1.

ISO 15147:2012 specifies methods for the measurement of widths and lengths of cut light conveyor belts as described in ISO 21183-1 and specifies the tolerances on the dimensions.

ISO 9980:2012 specifies the methods of checking the regularity of the grooves and pulleys for V-belts specified in the system based on effective width. The grooved pulleys can be designed for use with classical or narrow V-belts. The V-belts can be either single or joined units.

ISO 18573:2012 specifies the temperature, humidity and time conditions used for the conditioning and testing of all types of conveyor belt, irrespective of whether they have plastics or rubber covers. It also specifies the requirements for the time interval to be observed between production and testing of conveyor belt test pieces. Special conditions applicable to a particular test or material or simulating a particular climatic environment are not included.

ISO 4195:2012 specifies requirements and test methods for the relative level of heat resistance of conveyor belt covers made of rubber. It gives the permissible variations of hardness, elongation at break and tensile strength after exposure to heat. It is applicable only to those conveyor belts having a cover thickness greater than or equal to 4 mm. It is not suitable or valid for light conveyor belts as described in ISO 21183-1.

ISO 5285:2012 gives guidelines for creating the most suitable conditions for the storage and handling of conveyor belts. It is not applicable to light conveyor belts, as described in ISO 21883-1.

This International Standard specifies the widths and lengths of conveyor belts with a textile carcass. It also specifies the corresponding tolerances. It is not applicable to light conveyor belts as described in ISO 21183-1, as tolerances on the widths and lengths of cut light conveyor belts are given in ISO 15147.

ISO 1120:2012 specifies a static test method for measuring the strength of a conveyor belt mechanical fastening; the mechanical joints can be either of the type employing a connecting rod or of a type which does not employ a connecting rod.

This International Standard specifies test methods for determining the physical properties of synchronous belts used in driving engine parts, such as camshafts, fuel injection pumps, balancing shafts. These test methods are intended to provide a means of characterizing synchronous belt properties for belts which are evaluated and qualified by dynamic laboratory and field testing. NOTE The dimensional characteristics of these belts are the subject of ISO 9010.

ISO 5291:2011 specifies the principal characteristics of grooved pulleys (for groove sections AJ, BJ, CJ and DJ), intended to take joined classical V-belts for industrial power transmission drives.

This International Standard specifies the characteristics of quality which are common to all transmission pulleys. It establishes specific quality levels for the finish and balance of transmission pulleys and test pulleys. This International Standard is applicable to transmission pulleys for V-belts, V-ribbed belts, flat or synchronous belts; it does not apply to those pulleys for variable speed drives that have one or more moving flanges. The other characteristics of transmission pulleys can be found in the relevant International Standards.

This International Standard specifies the formula for calculating conveyor belt transition distances and details its application and derivation. This International Standard is not suitable or valid for light conveyor belts as described in ISO 21183-1.