278/2009 - Commission Regulation (EC) No 278/2009 implementing Directive 2005/32/EC of the European Parliament and of the Council with regard to ecodesign requirements for no-load condition electric power consumption and average active efficiency of external power supplies

This European Standard specifies a procedure for obtaining a migration water to determine odour and flavour for products made from organic materials intended to come in contact with water for human consumption (drinking water) and used in piping systems. Such products include pipes, fittings, ancillaries and coatings.
This standard is applicable to products to be used under various conditions for the transport, storage and distribution of water intended for human consumption and raw water used for the manufacture of water intended for human consumption.
This standard specifies a test method comprising of a set of procedures. The use may be dependent on the relevant national regulations and/or the system or product standards.

This European standard specifies a procedure for obtaining a migration water to determine odour and flavour for products made from organic materials intended to come in contact with water for human consumption (drinking water) and used in piping systems. Such products include pipes, fittings, ancillaries and coatings.
This standard is applicable to products to be used under various conditions for the transport, storage and distribution of water intended for human consumption and raw water used for the manufacture of water intended for human consumption.
This standard specifies a test method comprising of a set of procedures. The use may be dependent on the relevant national regulations and/or the system or product standards.

This European Standard specifies the requirements for factory made expanded perlite and exfoliated vermiculite products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately 0 °C to + 1 100 °C.Expanded perlite and exfoliated vermiculite products can be used below 0 °C but special tests regarding the suitability of the product in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer¿s advice should be heeded in all cases.The products are manufactured in the form of boards, pipe sections, segments, prefabricated ware and special ware.This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.Products covered by this European Standard are also used in prefabricated thermal insulation systems and composite panels; the structural performance of systems incorporating these products is not covered.This European Standard does not specify the required level of a given property that is achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.Products with a declared thermal conductivity greater than 0,6 W/(mK) at 10 °C are not covered by this European Standard.This European Standard does not cover products intended to be used for the insulation of the building structure.The European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact transmission noise index.

This European Standard specifies the requirements for factory made expanded perlite and exfoliated vermiculite products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately 0 °C to + 1 100 °C.
Expanded perlite and exfoliated vermiculite products can be used below 0 °C but special tests regarding the suitability of the product in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer’s advice should be heeded in all cases.
The products are manufactured in the form of boards, pipe sections, segments, prefabricated ware and special ware.
This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
Products covered by this European Standard are also used in prefabricated thermal insulation systems and composite panels; the structural performance of systems incorporating these products is not covered.
This European Standard does not specify the required level of a given property that is achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.
Products with a declared thermal conductivity greater than 0,6 W/(mK) at 10 °C are not covered by this European Standard.
This European Standard does not cover products intended to be used for the insulation of the building structure.
The European Standard does not cover the following acoustical aspects: direct airborne sound insulation and impact transmission noise index.

This European Standard specifies methods of measurement of electrical power consumption, and the reporting of results, for external power supplies. This standard is applicable to external power supplies with a rated input voltage within the range 100 V ac to 250 V ac having a single output with a rated output power not exceeding 250 W and a rated output voltage not exceeding 230 V a.c. or 325 V d.c. The output voltage may be either at a fixed voltage, or at a voltage which is user selectable, or at a voltage that is automatically selectable by the external power supply so as to be compatible with one or more product-loads.

2013-08-27: Publication allocated to cpalagi@cencenelec.eu
2021: CLC legacy converted by DCLab NISOSTS

This European Standard specifies methods of measurement of electrical power consumption, and the reporting of results, for external power supplies. This standard is applicable to external power supplies with a rated input voltage within the range 100 V ac to 250 V ac having a single output with a rated output power not exceeding 250 W and a rated output voltage not exceeding 230 V a.c. or 325 V d.c. The output voltage may be either at a fixed voltage, or at a voltage which is user selectable, or at a voltage that is automatically selectable by the external power supply so as to be compatible with one or more product-loads.

This European Standard specifies methods of measurement of electrical power consumption, and the reporting of results, for external power supplies. This standard is applicable to external power supplies with a rated input voltage within the range 100 V ac to 250 V ac having a single output with a rated output power not exceeding 250 W and a rated output voltage not exceeding 230 V a.c. or 325 V d.c. The output voltage may be either at a fixed voltage, or at a voltage which is user selectable, or at a voltage that is automatically selectable by the external power supply so as to be compatible with one or more product-loads.

This European Standard provides a framework for specifying a range of properties and relevant test methods for bitumens, which are suitable for use in the construction and maintenance of roads, airfields and other paved areas, together with requirements for assessment and verification of constancy of performance.
This European Standard does not directly address ‘cohesion, adhesion and setting ability’ (see Introduction).
NOTE   Although industrial bitumens are specified according to EN 13305, it is underlined that paving grade bitumens, specified according to this European Standard, can also be used for industrial applications.

This European Standard provides a framework for specifying a range of properties and relevant test methods for bitumens, which are suitable for use in the construction and maintenance of roads, airfields and other paved areas, together with requirements for evaluation of conformity. This European Standard does not directly address ‘cohesion, adhesion and setting ability’ (see Introduction). NOTE Although industrial bitumens are specified according to EN 13305, it should be underlined that paving grade bitumens, specified according to this European Standard, can also be used for industrial applications.