M/439 - EuPs

IEC 62301:2011 specifies methods of measurement of electrical power consumption in standby mode(s) and other low power modes (off mode and network mode), as applicable. It is applicable to electrical products with a rated input voltage or voltage range that lies wholly or partly in the range 100 V a.c. to 250 V a.c. for single phase products and 130 V a.c. to 480 V a.c. for other products. The objective of this standard is to provide a method of test to determine the power consumption of a range of products in relevant low power modes (see 3.4), generally where the product is not in active mode (i.e. not performing a primary function). This standard does not specify safety requirements. It does not specify minimum performance requirements nor does it set maximum limits on power or energy consumption. This second edition cancels and replaces the first edition published in 2005 and constitutes a technical revision. The main changes from the previous edition are as follows: - greater detail in set-up procedures and introduction of stability requirements for all measurement methods to ensure that results are as representative as possible; - refinement of measurement uncertainty requirements for power measuring instruments, especially for more difficult loads with high crest factor and/or low power factor; - updated guidance on product configuration, instrumentation and calculation of measurement uncertainty; - inclusion of definitions for low power modes as requested by TC59 and use of these new definitions and more rigorous terminology throughout the standard; - inclusion of specific test conditions where power consumption is affected by ambient illumination.

This part of IEC 60704 applies to electric appliances (including their accessories or components) for household and similar use, supplied from mains or from batteries. By similar use is understood the use in similar conditions as in households, for example in inns, coffee-houses, tea-rooms, hotels, barber or hairdresser shops, launderettes, etc., if not otherwise specified in part 2. This standard does not apply to - appliances, equipment or machines designed exclusively for industrial or professional purposes; - appliances which are integrated parts of a building or its installations, such as equipment for air conditioning, heating and ventilating (except household fans, cooker hoods and free standing heating appliances), oil burners for central heating, pumps for water supply and for sewage systems; - separate motors or generators; - appliances for outdoor use.

2022-01-12: This A11 is replaced by 2021 edition but will stay active, as 2021 edition is published without DOW, further to  BT Decision D169/C126

IEC 62301:2011 specifies methods of measurement of electrical power consumption in standby mode(s) and other low power modes (off mode and network mode), as applicable. It is applicable to electrical products with a rated input voltage or voltage range that lies wholly or partly in the range 100 V a.c. to 250 V a.c. for single phase products and 130 V a.c. to 480 V a.c. for other products. The objective of this standard is to provide a method of test to determine the power consumption of a range of products in relevant low power modes (see 3.4), generally where the product is not in active mode (i.e. not performing a primary function). This standard does not specify safety requirements. It does not specify minimum performance requirements nor does it set maximum limits on power or energy consumption. This second edition cancels and replaces the first edition published in 2005 and constitutes a technical revision. The main changes from the previous edition are as follows:  - greater detail in set-up procedures and introduction of stability requirements for all measurement methods to ensure that results are as representative as possible;  - refinement of measurement uncertainty requirements for power measuring instruments, especially for more difficult loads with high crest factor and/or low power factor;  - updated guidance on product configuration, instrumentation and calculation of measurement uncertainty;  - inclusion of definitions for low power modes as requested by TC59 and use of these new definitions and more rigorous terminology throughout the standard;  - inclusion of specific test conditions where power consumption is affected by ambient illumination.

This standard applies to electric dishwashers for household use that are supplied with hot and/or cold water.
The object is to state and define the principal performance characteristics of electric dishwashers for household use and to describe the standard methods of measuring these characteristics.
This standard is concerned neither with safety nor with performance requirements.

This standard applies to electric dishwashers for household use that are supplied with hot and/or cold water. The object is to state and define the principal performance characteristics of electric dishwashers for household use and to describe the standard methods of measuring these characteristics. This standard is concerned neither with safety nor with performance requirements.