ASTM D664-11ae1
(Test Method)Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
SIGNIFICANCE AND USE
5.1 New and used petroleum products, biodiesel and blends of biodiesel may contain acidic constituents that are present as additives or as degradation products formed during service, such as oxidation products. The relative amount of these materials can be determined by titrating with bases. The acid number is a measure of this amount of acidic substance in the oil, always under the conditions of the test. The acid number is used as a guide in the quality control of lubricating oil formulations. It is also sometimes used as a measure of lubricant degradation in service. Any condemning limits must be empirically established.
5.2 Since a variety of oxidation products contribute to the acid number and the organic acids vary widely in corrosion properties, the test method cannot be used to predict corrosiveness of oil or biodiesel and blends under service conditions. No general correlation is known between acid number and the corrosive tendency of biodiesel and blends or oils toward metals.
SCOPE
1.1 This test method covers procedures for the determination of acidic constituents in petroleum products, lubricants, biodiesel and blends of biodiesel.
1.1.1 Test Method A—For petroleum products and lubricants soluble or nearly soluble in mixtures of toluene and propan-2-ol. It is applicable for the determination of acids whose dissociation constants in water are larger than 10-9; extremely weak acids whose dissociation constants are smaller than 10-9 do not interfere. Salts react if their hydrolysis constants are larger than 10-9. The range of acid numbers included in the precision statement is 0.1 mg/g KOH to 150 mg/g KOH.
1.1.2 Test Method B—Developed specifically for biodiesel and biodiesel blends with low acidity and slightly different solubility. This test method requires the use of an automatic titrator with automatic endpoint seeking capability.
Note 1: In new and used oils, the constituents that may be considered to have acidic characteristics include organic and inorganic acids, esters, phenolic compounds, lactones, resins, salts of heavy metals, salts of ammonia and other weak bases, acid salts of polybasic acids, and addition agents such as inhibitors and detergents.
1.2 The test method may be used to indicate relative changes that occur in oil during use under oxidizing conditions regardless of the color or other properties of the resulting oil. Although the titration is made under definite equilibrium conditions, the test method is not intended to measure an absolute acidic property that can be used to predict performance of oil under service conditions. No general relationship between bearing corrosion and acid number is known.
Note 2: The acid number obtained by this standard may or may not be numerically the same as that obtained in accordance with Test Methods D974 and D3339. There has not been any attempt to correlate this method with other non-titration methods.
Note 3: A few laboratories have made the observation that there is a difference in Test Method D664 results when aqueous versus nonaqueous buffers are used.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D664 − 11a British Standard 4457
Designation 177/96
Standard Test Method for
Acid Number of Petroleum Products by Potentiometric
1
Titration
This standard is issued under the fixed designation D664; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Subsection 14.5 was corrected editorially in September 2016.
NOTE2—Theacidnumberobtainedbythisstandardmayormaynotbe
1. Scope*
numerically the same as that obtained in accordance with Test Methods
1.1 This test method covers procedures for the determina-
D974andD3339.Therehasnotbeenanyattempttocorrelatethismethod
tion of acidic constituents in petroleum products, lubricants, with other non-titration methods.
NOTE 3—A few laboratories have made the observation that there is a
biodiesel and blends of biodiesel.
difference in Test Method D664 results when aqueous versus nonaqueous
1.1.1 Test Method A—Forpetroleumproductsandlubricants
buffers are used.
soluble or nearly soluble in mixtures of toluene and propan-2-
1.3 The values stated in SI units are to be regarded as
ol. It is applicable for the determination of acids whose
-9
standard. No other units of measurement are included in this
dissociation constants in water are larger than 10 ; extremely
-9
standard.
weak acids whose dissociation constants are smaller than 10
do not interfere. Salts react if their hydrolysis constants are
1.4 This standard does not purport to address all of the
-9
larger than 10 . The range of acid numbers included in the safety concerns, if any, associated with its use. It is the
precision statement is 0.1 mg/g KOH to 150 mg/g KOH.
responsibility of the user of this standard to establish appro-
1.1.2 Test Method B—Developed specifically for biodiesel priate safety and health practices and determine the applica-
and biodiesel blends with low acidity and slightly different
bility of regulatory limitations prior to use.
solubility. This test method requires the use of an automatic
2. Referenced Documents
titrator with automatic endpoint seeking capability.
2
NOTE 1—In new and used oils, the constituents that may be considered
2.1 ASTM Standards:
to have acidic characteristics include organic and inorganic acids, esters,
D974Test Method for Acid and Base Number by Color-
phenolic compounds, lactones, resins, salts of heavy metals, salts of
Indicator Titration
ammoniaandotherweakbases,acidsaltsofpolybasicacids,andaddition
D1193Specification for Reagent Water
agents such as inhibitors and detergents.
D3339TestMethodforAcidNumberofPetroleumProducts
1.2 The test method may be used to indicate relative
by Semi-Micro Color Indicator Titration
changesthatoccurinoilduringuseunderoxidizingconditions
D4057Practice for Manual Sampling of Petroleum and
regardless of the color or other properties of the resulting oil.
Petroleum Products
Although the titration is made under definite equilibrium
D4177Practice for Automatic Sampling of Petroleum and
conditions, the test method is not intended to measure an
Petroleum Products
absolute acidic property that can be used to predict perfor-
E177Practice for Use of the Terms Precision and Bias in
mance of oil under service conditions. No general relationship
ASTM Test Methods
between bearing corrosion and acid number is known.
3. Terminology
3.1 Definitions:
1
This test method is under the jurisdiction of ASTM Committee D02 on
3.1.1 acid number, n—the quantity of a specified base,
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
Subcommittee D02.06 on Analysis of Liquid Fuels and Lubricants. expressed in milligrams of potassium hydroxide per gram of
Current edition approved July 15, 2011. Published August 2011. Originally
approved in 1942. Last previous edition approved in 2011 as D664 – 11. DOI:
2
10.1520/D0664-11AE01. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
This test method was adopted as a jointASTM-IPstandard in 1964.ASTM Test contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Method D4739 has been developed as an alternative to the base number portion of Standards volume information, refer to the standard’s Document Summary page on
D664. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D664 − 11a
sample, required to titrate a sample in a specified sol
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D664 − 11a D664 − 11a British Standard 4457
Designation 177/96
Standard Test Method for
Acid Number of Petroleum Products by Potentiometric
1
Titration
This standard is issued under the fixed designation D664; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Subsection 14.5 was corrected editorially in September 2016.
1. Scope*
1.1 This test method covers procedures for the determination of acidic constituents in petroleum products, lubricants, biodiesel
and blends of biodiesel.
1.1.1 Test Method A—For petroleum products and lubricants soluble or nearly soluble in mixtures of toluene and propan-2-ol.
-9
It is applicable for the determination of acids whose dissociation constants in water are larger than 10 ; extremely weak acids
-9 -9
whose dissociation constants are smaller than 10 do not interfere. Salts react if their hydrolysis constants are larger than 10 . The
range of acid numbers included in the precision statement is 0.1 mg/g KOH to 150 mg/g KOH.
1.1.2 Test Method B—Developed specifically for biodiesel and biodiesel blends with low acidity and slightly different solubility.
This test method requires the use of an automatic titrator with automatic endpoint seeking capability.
NOTE 1—In new and used oils, the constituents that may be considered to have acidic characteristics include organic and inorganic acids, esters,
phenolic compounds, lactones, resins, salts of heavy metals, salts of ammonia and other weak bases, acid salts of polybasic acids, and addition agents
such as inhibitors and detergents.
1.2 The test method may be used to indicate relative changes that occur in oil during use under oxidizing conditions regardless
of the color or other properties of the resulting oil. Although the titration is made under definite equilibrium conditions, the test
method is not intended to measure an absolute acidic property that can be used to predict performance of oil under service
conditions. No general relationship between bearing corrosion and acid number is known.
NOTE 2—The acid number obtained by this standard may or may not be numerically the same as that obtained in accordance with Test Methods D974
and D3339. There has not been any attempt to correlate this method with other non-titration methods.
NOTE 3—A few laboratories have made the observation that there is a difference in Test Method D664 results when aqueous versus nonaqueous buffers
are used.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D974 Test Method for Acid and Base Number by Color-Indicator Titration
D1193 Specification for Reagent Water
D3339 Test Method for Acid Number of Petroleum Products by Semi-Micro Color Indicator Titration
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.06 on Analysis of Liquid Fuels and Lubricants.
Current edition approved July 15, 2011. Published August 2011. Originally approved in 1942. Last previous edition approved in 2011 as D664–11. DOI:
10.1520/D0664-11A. – 11. DOI: 10.1520/D0664-11AE01.
This test method was adopted as a joint ASTM-IP standard in 1964. ASTM Test Method D4739 has been developed as an alternative to the base number portion of D664.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, P
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.