ASTM D8157-19
(Guide)Standard Guide for Qualification Testing of Coatings Used in Coating Service Level I in Nuclear Power Plants
Standard Guide for Qualification Testing of Coatings Used in Coating Service Level I in Nuclear Power Plants
SIGNIFICANCE AND USE
4.1 This guide presents concise guidance and approach to developing a test document for qualifying a coating for CSLI service, whether a new or existing coating. Guidance for evaluating existing qualification test data for applicability is presented in Guide D8104.
4.2 The requirements for qualification testing can be found in Quality Assurance Criteria III (Design Control), IX (Control of Special Processes), and XI (Test Control) of 10 CFR 50, Appendix B, as implemented, respectively, by Requirements III, IX, and XI of NQA-1. A test document developed per this guide is intended to be compliant with these requirements.
4.3 This guide implements the guidance provided in Guide D5144 for qualification of coatings for use in CSLI service. Additional guidance is provided in Regulatory Guide 1.54, Revisions 0 through 3, as may be invoked by the licensee.
4.4 For plants with a license basis that predates the requirements of ANSI N5.12 and N101.2, this guide also is applicable. For these plants, the coatings or coating systems may be designated as acceptable, rather than qualified.
4.5 All qualification testing shall comply with the licensee’s approved quality assurance program.
SCOPE
1.1 This guide provides an approach to identifying the need for and development of a test document to qualify coatings for Coating Service Level I (CSLI) service in nuclear power plants.
1.2 It is the intent of this guide to provide a recommended basis for establishing a coatings qualification test document, not to mandate a singular basis for all test documents. Variations or simplifications of the process described in this guide may be appropriate for any given operating or new construction nuclear power plant depending on its licensing commitments.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D8157 −19
Standard Guide for
Qualification Testing of Coatings Used in Coating Service
1
Level I in Nuclear Power Plants
This standard is issued under the fixed designation D8157; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope the Guarded-Hot-Plate Apparatus
D3911 Test Method for Evaluating Coatings Used in Light-
1.1 This guide provides an approach to identifying the need
Water Nuclear Power Plants at Simulated Design Basis
for and development of a test document to qualify coatings for
Accident (DBA) Conditions
Coating Service Level I (CSLI) service in nuclear power
D3912 Test Method for Chemical Resistance of Coatings
plants.
and Linings for Use in Nuclear Power Plants
1.2 It is the intent of this guide to provide a recommended
D4060 Test Method for Abrasion Resistance of Organic
basis for establishing a coatings qualification test document,
Coatings by the Taber Abraser
not to mandate a singular basis for all test documents.
D4082 Test Method for Effects of Gamma Radiation on
Variations or simplifications of the process described in this
Coatings for Use in Nuclear Power Plants
guide may be appropriate for any given operating or new
D4538 Terminology Relating to Protective Coating and
construction nuclear power plant depending on its licensing
Lining Work for Power Generation Facilities
commitments.
D4541 Test Method for Pull-Off Strength of Coatings Using
Portable Adhesion Testers
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical D5139 Specification for Sample Preparation for Qualifica-
tion Testing of Coatings to be Used in Nuclear Power
conversions to SI units that are provided for information only
and are not considered standard. Plants
D5144 Guide for Use of Protective Coating Standards in
1.4 This standard does not purport to address all of the
Nuclear Power Plants
safety concerns, if any, associated with its use. It is the
D5163 Guide for Establishing a Program for Condition
responsibility of the user of this standard to establish appro-
Assessment of Coating Service Level I Coating Systems
priate safety, health, and environmental practices and deter-
in Nuclear Power Plants
mine the applicability of regulatory limitations prior to use.
D7108 Guide for Establishing Qualifications for a Nuclear
1.5 This international standard was developed in accor-
Coatings Specialist
dance with internationally recognized principles on standard-
D8104 Guide for Determining Coating Qualification Test
ization established in the Decision on Principles for the
Data Applicability
Development of International Standards, Guides and Recom-
E84 Test Method for Surface Burning Characteristics of
mendations issued by the World Trade Organization Technical
Building Materials
Barriers to Trade (TBT) Committee.
E648 Test Method for Critical Radiant Flux of Floor-
Covering Systems Using a Radiant Heat Energy Source
2. Referenced Documents
E1269 Test Method for Determining Specific Heat Capacity
2
2.1 ASTM Standards:
by Differential Scanning Calorimetry
C177 Test Method for Steady-State Heat Flux Measure-
E1461 Test Method for Thermal Diffusivity by the Flash
ments and Thermal Transmission Properties by Means of
Method
E1530 Test Method for Evaluating the Resistance to Ther-
mal Transmission by the Guarded Heat Flow Meter
1
This guide is under the jurisdiction of ASTM Committee D33 on Protective
Technique
Coating and Lining Work for Power Generation Facilities and is the direct
3
2.2 ANSI Standards:
responsibility of Subcommittee D33.04 on Quality Systems and Inspection.
Current edition approved March 1, 2019. Published March 2019. DOI: 10.1520/ ANSI N5.12 Protective Coatings (Paints) for the Nuclear
D8157-19.
Industry, 1974
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from IHS, 15 Inverness Way East, Englewood, CO 80112, http://
the ASTM website. www.global.ihs.com.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D8157−19
ANSI N101.2 Protective Coatings (Paints) for Light Water 4.3 This guide implements the guidance provided in Guide
Nuclear Reactor Containment Fa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.