ASTM E2075/E2075M-15(2020)
(Practice)Standard Practice for Verifying the Consistency of AE-Sensor Response Using an Acrylic Rod
Standard Practice for Verifying the Consistency of AE-Sensor Response Using an Acrylic Rod
SIGNIFICANCE AND USE
3.1 Degradation in sensor performance can occur due to dropping, mechanical shock while mounted on the test structure, temperature cycles, and so forth. It is necessary and desirable to have a simple measurement procedure that will check the consistency of sensor response, while holding all other variables constant.
3.2 While test blocks of many different kinds have been used for this purpose for many years, an acrylic polymer rod offers the best all-around combination of suitable acoustic properties, practical convenience, ease of procurement and low cost.
3.3 Because the acoustic properties of the acrylic rod are known to depend on temperature, this practice requires that the rod, sensors, and couplant be stabilized at the same working temperature, prior to verifying the sensors.
3.4 Attention should be paid to storage conditions for the acrylic polymer rod. For example, it should not be left in a freezing or hot environment overnight, unless it is given time for temperature stabilization before use.
3.5 Properly applied and with proper record keeping, this practice can be used in many ways. The user organization must determine the context for its use, the acceptance standards and the actions to be taken based on the lead break results. The following uses are suggested:
3.5.1 To determine when a sensor is no longer suitable for use.
3.5.2 To check sensors that have been exposed to high-risk conditions, such as dropping, overheating, and so forth.
3.5.3 To get an early warning of sensor degradation over time. This can lead to identifying conditions of use, which are damaging sensors, and thus, to better equipment care and lower replacement costs.
3.5.4 To obtain matched sets of sensors, preamplifiers, instrumentation channels, or a combination thereof, for more uniform performance of the total system.
3.5.5 To save time and money, by eliminating the installation of bad sensors.
3.5.6 To verify sensors quickly but consistently in the fi...
SCOPE
1.1 This practice is used for routinely checking the sensitivity of acoustic emission (AE) sensors. It is intended to provide a reliable, precisely specified way of comparing a set of sensors, or telling whether an individual sensor's sensitivity has degraded during its service life, or both.
1.2 This practice is not a “calibration” nor does it give frequency response information.
1.3 Units—The values stated in SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: E2075/E2075M − 15 (Reapproved 2020)
Standard Practice for
Verifying the Consistency of AE-Sensor Response Using an
Acrylic Rod
ThisstandardisissuedunderthefixeddesignationE2075/E2075M;thenumberimmediatelyfollowingthedesignationindicatestheyear
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* E976 GuideforDeterminingtheReproducibilityofAcoustic
Emission Sensor Response
1.1 This practice is used for routinely checking the sensi-
E2374 Guide for Acoustic Emission System Performance
tivity of acoustic emission (AE) sensors. It is intended to
Verification
provide a reliable, precisely specified way of comparing a set
of sensors, or telling whether an individual sensor’s sensitivity
3. Significance and Use
has degraded during its service life, or both.
3.1 Degradation in sensor performance can occur due to
1.2 This practice is not a “calibration” nor does it give
dropping, mechanical shock while mounted on the test
frequency response information.
structure, temperature cycles, and so forth. It is necessary and
1.3 Units—The values stated in SI units or inch-pound units
desirable to have a simple measurement procedure that will
are to be regarded separately as standard. The values stated in
check the consistency of sensor response, while holding all
each system may not be exact equivalents; therefore, each
other variables constant.
system shall be used independently of the other. Combining
3.2 While test blocks of many different kinds have been
values from the two systems may result in non-conformance
used for this purpose for many years, an acrylic polymer rod
with the standard.
offers the best all-around combination of suitable acoustic
1.4 This standard does not purport to address all of the
properties, practical convenience, ease of procurement and low
safety concerns, if any, associated with its use. It is the
cost.
responsibility of the user of this standard to establish appro-
3.3 Because the acoustic properties of the acrylic rod are
priate safety, health, and environmental practices and deter-
known to depend on temperature, this practice requires that the
mine the applicability of regulatory limitations prior to use.
rod, sensors, and couplant be stabilized at the same working
1.5 This international standard was developed in accor-
temperature, prior to verifying the sensors.
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
3.4 Attention should be paid to storage conditions for the
Development of International Standards, Guides and Recom-
acrylic polymer rod. For example, it should not be left in a
mendations issued by the World Trade Organization Technical
freezing or hot environment overnight, unless it is given time
Barriers to Trade (TBT) Committee.
for temperature stabilization before use.
3.5 Properly applied and with proper record keeping, this
2. Referenced Documents
practice can be used in many ways.The user organization must
2.1 ASTM Standards:
determine the context for its use, the acceptance standards and
E650 Guide for Mounting Piezoelectric Acoustic Emission
the actions to be taken based on the lead break results. The
Sensors
following uses are suggested:
E750 Practice for Characterizing Acoustic Emission Instru-
3.5.1 To determine when a sensor is no longer suitable for
mentation
use.
3.5.2 To check sensors that have been exposed to high-risk
This practice is under the jurisdiction of ASTM Committee E07 on Nonde- conditions, such as dropping, overheating, and so forth.
structive Testing and is the direct responsibility of Subcommittee E07.04 on
3.5.3 To get an early warning of sensor degradation over
Acoustic Emission Method.
time. This can lead to identifying conditions of use, which are
CurrenteditionapprovedJune1,2020.PublishedJuly2020.Originallyapproved
damagingsensors,andthus,tobetterequipmentcareandlower
in 2000. Last previous edition approved in 2015 as E2075/E2075M – 15. DOI:
10.1520/E2075_E2075M-15R20.
replacement costs.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.5.4 To obtain matched sets of sensors, preamplifiers,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
instrumentation channels, or a combination thereof, for more
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. uniform performance of the total system.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
E2075/E2075M − 15 (2020)
3.5.5 To save time and money, by eliminating the installa- 4.5 Couplant, to be standardized and documented by the
tion of bad sensors. user of this practice.
3.5.6 To verify sensors quickly but consistently in the field
5. Procedure
and to assist trouble-shooting when a channel does not pass a
performance check.
FIG. 1 Acrylic Rod Description
3.6 All the above uses are recommended for consideration. 5.1 Ensure that the acrylic rod, sensors and couplant have
Thepurposeofthispracticeisnottocallouthowtheseusesare been allowed to stabilize to the ambient temperature of the
to be implemented, but only to state how the test itself is to be examination environment.
performed so that the results obtained will be accurate and
5.2 Place the prepared acrylic rod horizontally on a suitable
reliable.
hard, flat surface, such as a benchtop, with the reference
mark(s) facing vertically up (12 o’clock). The rod may be
4. Apparatus
secured with tape or other means no closer than 30.5 cm
4.1 Acrylic Polymer Cylindrical Rod (Fig. 1), should be
[12 in.] from the reference mark.
used. The actual material of the acrylic polymer rod is
5.3 Prepare and power-up the AE measurement system
polymethylmethacrylate.
including preamplifier (if used) and connecting cables; allow
4.1.1 The rod shall be cast, not extruded.
warm up time as necessary. Verify the system’s performance.
4.1.2 Dimensions of the rod should be 78.7 cm [31 in.] long
Verification may be accomplished on the rod using a reference
by3.8cm[1.5in.]indiameter,sensorsendcuttrueandsmooth
sensor that is dedicated to this purpose and not exposed to the
with a surface finish of 0.4 µm RMS [0.16 µin.].
hazards of field use; or, it may be accomplished by electronic
4.1.3 Other lengths of rod are acceptable
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.