ASTM F3182-23

Standard Practice for the Application of Spray-Applied Polymeric Liners Inside Pipelines for Potable Water

SIGNIFICANCE AND USE
5.1 This practice is for use by water utilities or other owners, contractors, specifiers, regulatory agencies, inspection organizations or other users who are involved in the rehabilitation of potable water pipelines and wish to specify or permit the use of spray-applied polymeric liners.
SCOPE
1.1 This practice describes the procedures for the rehabilitation of potable water pipes using spray-applied polymeric coatings for pipelines constructed of iron, steel, or asbestos cement using resin materials that have been certified in accordance with NSF/ANSI 61 for the in-situ lining of potable water mains.  
1.2 This practice applies to potable water pipelines constructed of metallic or non-metallic piping in the diameter ranges of 4 in. (10 cm) to 36 in. (90 cm). Specialist advice should be sought from the product manufacturer for polymeric linings applied to other nonmetallic surfaces and for applied linings outside of these diametric limitations.  
1.3 This practice applies to in-situ pipes requiring AWWA Class I (nonstructural) linings through Class III (semi-structural) linings (see AWWA M28).  
1.4 This practice does not address lining system design. Assistance with lining system design is available from lining system manufacturers and operators who have been professionally trained and experienced in polymeric liner design.  
1.5 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 14-Feb-2023
• ICS: 91.140.60 - Water supply systems
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.67 - Trenchless Plastic Pipeline Technology

Relations

• Refers: ASTM F412-20 - Standard Terminology Relating to Plastic Piping Systems
• Effective Date: 01-Apr-2020

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F3182 − 23
Standard Practice for
the Application of Spray-Applied Polymeric Liners Inside
1
Pipelines for Potable Water
This standard is issued under the fixed designation F3182; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This practice describes the procedures for the rehabili-
2.1 ASTM Standards:
tation of potable water pipes using spray-applied polymeric
D883 Terminology Relating to Plastics
coatings for pipelines constructed of iron, steel, or asbestos
D1600 Terminology for Abbreviated Terms Relating to Plas-
cement using resin materials that have been certified in
tics
accordance with NSF/ANSI 61 for the in-situ lining of potable
D3359 Test Methods for Rating Adhesion by Tape Test
water mains.
D4541 Test Method for Pull-Off Strength of Coatings Using
1.2 This practice applies to potable water pipelines con- Portable Adhesion Testers
D6677 Test Method for Evaluating Adhesion by Knife
structed of metallic or non-metallic piping in the diameter
ranges of 4 in. (10 cm) to 36 in. (90 cm). Specialist advice D7091 Practice for Nondestructive Measurement of Dry
should be sought from the product manufacturer for polymeric Film Thickness of Nonmagnetic Coatings Applied to
linings applied to other nonmetallic surfaces and for applied Ferrous Metals and Nonmagnetic, Nonconductive Coat-
linings outside of these diametric limitations. ings Applied to Non-Ferrous Metals
F412 Terminology Relating to Plastic Piping Systems
1.3 This practice applies to in-situ pipes requiring AWWA
3
Class I (nonstructural) linings through Class III (semi- 2.2 AWWA Documents:
structural) linings (see AWWA M28).
AWWA C651 Disinfecting Water Mains
AWWA M28 Rehabilitation of Water Mains
1.4 This practice does not address lining system design.
AWWA C222 Polyurethane coatings for the Interior and
Assistance with lining system design is available from lining
Exterior of Steel Water Pipe and Fittings
system manufacturers and operators who have been profession-
4
ally trained and experienced in polymeric liner design.
2.3 NSF Standards:
NSF/ANSI 61 Drinking Water System Components – Health
1.5 Units—The values stated in inch-pound units are to be
Effects
regarded as standard. The values given in parentheses are
NSF/ANSI 14 Plastic Piping System Components and Re-
mathematical conversions to SI units that are provided for
lated Materials
information only and are not considered standard.
NSF/ANSI 372 Drinking Water System Components – Lead
1.6 This standard does not purport to address all of the
Content
safety concerns, if any, associated with its use. It is the
5,6
2.4 Society of Protective Coating/NACE Standards:
responsibility of the user of this standard to establish appro-
SSPC-SP 6 /NACE NO. 3 Commercial Blast Cleaning
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use. SSPC-SP 7 /NACE NO. 4 Brush-off Blast Cleaning
1.7 This international standard was developed in accor-
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Development of International Standards, Guides and Recom-
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
mendations issued by the World Trade Organization Technical
the ASTM website.
Barriers to Trade (TBT) Committee.
3
Available from American Water Works Association (AWWA), 6666 W. Quincy
Ave., Denver, CO 80235, http://www.awwa.org.
1 4
This practice is under the jurisdiction of ASTM Committee F17 on Plastic Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann
Piping Systems and is the direct responsibility of Subcommittee F17.67 on Arbor, MI 48105, http://www.nsf.org.
th
5
Trenchless Plastic Pipeline Technology. Available from The Society for Protective Coatings, 40 24 Street, Sixth Floor,
Current edition approved Feb. 15, 2023. Published March 2023. Originally Pittsburgh, PA 15222
6
approved in 2016. Last previous edition approved in 2016 as F3182–16. DOI: Available from NACE International (NACE), 15835 Park Ten Pl., Houston, TX
10.1520/F3182–23 77084, http://www.nace.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM Internation
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F3182 − 16 F3182 − 23
Standard Practice for
the Application of Spray-Applied Polymeric Liners Inside
1
Pipelines for Potable Water
This standard is issued under the fixed designation F3182; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This practice describes the procedures for the rehabilitation of potable water pipes using spray-applied polymeric coatings for
pipelines constructed of iron, steel, or asbestos cement using resin materials that have been certified in accordance with NSF/ANSI
Standard 61 for the in-situ lining of potable water mains.
1.2 This practice applies to potable water pipelines constructed of metallic or asbestos cement non-metallic piping in the diameter
ranges of 4 in. (10 cm) to 36 in. (90 cm). Specialist advice should be sought from the product manufacturer for polymeric linings
applied to other nonmetallic surfaces and for applied linings outside of these diametric limitations.
1.3 This practice applies to in-situ pipes requiring AWWA Class I (nonstructural) linings through Class III (semi-structural) linings
(see AWWA M28).
1.4 This practice does not address lining system design. Assistance with lining system design is available from lining system
manufacturers and operators who have been professionally trained and experienced in polymeric liner design.
1.5 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and healthsafety, health, and environmental practices and determine
the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D883 Terminology Relating to Plastics
D1600 Terminology for Abbreviated Terms Relating to Plastics
D3359 Test Methods for Rating Adhesion by Tape Test
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.67 on Trenchless Plastic
Pipeline Technology.
Current edition approved June 1, 2016Feb. 15, 2023. Published June 2016March 2023. Originally approved in 2016. Last previous edition approved in 2016 as F3182–16.
DOI: 10.1520/F3182–1610.1520/F3182–23
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F3182 − 23
D4541 Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
D6677 Test Method for Evaluating Adhesion by Knife
D7091 Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals
and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals
F412 Terminology Relating to Plastic Piping Systems
3
2.2 AWWA Documents:
AWWA C651 Disinfecting Water Mains
AWWA M28 Rehabilitation of Water Mains
AWWA C222 Polyurethane coatings for the Interior and Exterior of Steel Water Pipe and Fittings
4
2.3 NSF Standards:
NSF/ANSI 61 Drinking Water System Components – Health Effects
NSF/ANSI 14 Plastic Piping System Components and Related Materials
NSF/ANSI 372 Drinking Water System Components – Lead Content
5,6
2.4 Society of Protective Coating/NACE Standards:
SSPC-SP 6 /NACE NO. 3 Commercial Blast Cleaning
SSPC-SP 7 /NACE NO. 4 Brush-off Blast Cleaning
3. Terminology
3.1 Definitions: Definitions are in accordance with Terminology F412 and a
...