ASTM B819-19
(Specification)Standard Specification for Seamless Copper Tube for Medical Gas Systems
Standard Specification for Seamless Copper Tube for Medical Gas Systems
ABSTRACT
This specification establishes the requirements for two wall thickness schedules of specially cleaned, straight lengths of seamless copper tube, identified as Types K and L, suitable for medical gas systems. The product shall be manufactured by such hot working necessary to convert the billet to a tubular shape and cold worked to the finished size. Seamless copper tube for medical gas systems shall be furnished in the H58 (Drawn General Purpose) temper. Tension test and Rockwell hardness test shall be performed to determine the tube's tensile strength and hardness, respectively. Eddy-current test, a nondestructive test, shall be performed as well. The tubes used for medical gas systems shall be cleaned by any of the following recommended methods: alkaline washing, steam solvent washing, steam detergent washing, steam washing, vapor degreasing, and refrigerant degreasing.
SIGNIFICANCE AND USE
17.1 For purpose of determining compliance with the specified limits for requirements of the properties listed in Table 9, an observed value or calculated value shall be rounded as indicated in accordance with the rounding of Practice E29.
SCOPE
1.1 This specification establishes the requirements for two wall thickness schedules of specially cleaned, straight lengths of seamless copper tube, identified as Types K and L, suitable for medical gas systems. The tube shall be installed in conformance with the requirements of the National Fire Protection Association (NFPA) Standard 99, Gas and Vacuum Systems (NFPA) Standard 99C, Standard for Hypobaric Facilities (NFPA) Standard 99B, and Canadian Standards Association (CSA) Standard Z 305.1/Z 7396.1, Nonflammable Medical Gas Piping Systems.
Note 1: Types K and L tube are defined in Specification B88.
Note 2: Drawn temper tube is suitable for use with capillary (solder joint) fittings for brazing.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazard caveat pertains only to the test method portion of Section 12 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.2
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:B819 −19
Standard Specification for
1
Seamless Copper Tube for Medical Gas Systems
This standard is issued under the fixed designation B819; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This specification establishes the requirements for two
wall thickness schedules of specially cleaned, straight lengths
2. Referenced Documents
of seamless copper tube, identified as Types K and L, suitable
3
2.1 ASTM Standards:
for medical gas systems. The tube shall be installed in
B88Specification for Seamless Copper Water Tube
conformance with the requirements of the National Fire
B601ClassificationforTemperDesignationsforCopperand
Protection Association (NFPA) Standard99, Gas and Vacuum
Copper Alloys—Wrought and Cast
Systems(NFPA)Standard99C,StandardforHypobaricFacili-
B846Terminology for Copper and Copper Alloys
ties (NFPA) Standard 99B, and Canadian Standards Associa-
E8/E8MTest Methods for Tension Testing of Metallic Ma-
tion (CSA) Standard Z305.1⁄Z7396.1, Nonflammable Medi-
terials
cal Gas Piping Systems.
E18Test Methods for Rockwell Hardness of Metallic Ma-
NOTE 1—Types K and L tube are defined in Specification B88.
terials
NOTE 2—Drawn temper tube is suitable for use with capillary (solder
E29Practice for Using Significant Digits in Test Data to
joint) fittings for brazing.
Determine Conformance with Specifications
1.2 Thevaluesstatedininch-poundunitsaretoberegarded
E53Test Method for Determination of Copper in Unalloyed
as standard. The values given in parentheses are mathematical
Copper by Gravimetry
conversions to SI units that are provided for information only
E62Test Methods for Chemical Analysis of Copper and
and are not considered standard. 4
CopperAlloys(PhotometricMethods)(Withdrawn2010)
1.3 The following safety hazard caveat pertains only to the E243PracticeforElectromagnetic(EddyCurrent)Examina-
test method portion of Section 12 of this specification. This
tion of Copper and Copper-Alloy Tubes
standard does not purport to address all of the safety concerns,
E255Practice for Sampling Copper and Copper Alloys for
if any, associated with its use. It is the responsibility of the user
the Determination of Chemical Composition
of this standard to establish appropriate safety, health, and
E527Practice for Numbering Metals and Alloys in the
environmental practices and determine the applicability of
Unified Numbering System (UNS)
2
regulatory limitations prior to use.
2.2 Other Standards:
1.4 This international standard was developed in accor-
National Fire Protection Association (NFPA) 99,Gas and
dance with internationally recognized principles on standard-
Vacuum Systems (NFPA) 99C and Standard for Hypo-
5
ization established in the Decision on Principles for the baric Facilities (NFPA) 99B
Development of International Standards, Guides and Recom-
CompressedGasAssociation(CGA)G-4.1,CleaningEquip-
6
ment for Oxygen Service
1 3
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper For referenced ASTM standards, visit the ASTM website, www.astm.org, or
and CopperAlloys and is the direct responsibility of Subcommittee B05.04 on Pipe contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and Tube. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Oct. 1, 2019. Published October 2019. Originally the ASTM website.
4
approved in 1992. Last previous edition approved in 2018 as B819–18. DOI: The last approved version of this historical standard is referenced on
10.1520/B0819–19. www.astm.org.
2 5
The UNS system for copper and copper alloys (see Practice E527) is a simple Available from National Fire Protection Association (NFPA), 1 Batterymarch
expansion of the former standard system accomplished by the addition of a prefix Park, Quincy, MA 02169, http://www.nfpa.org.
6
“C”andasuffix“00.”Thesuffixcanbeusedtoaccommodatecompositionvariation Available from Compressed Gas Association (CGA), 14501 George Carter
of the base alloy. Way, Suite 103, Chantilly VA 20151-2923, http://www.cganet.com.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B819−19
Canadian Standards Association (CSA)
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B819 − 18 B819 − 19
Standard Specification for
1
Seamless Copper Tube for Medical Gas Systems
This standard is issued under the fixed designation B819; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification establishes the requirements for two wall thickness schedules of specially cleaned, straight lengths of
seamless copper tube, identified as Types K and L, suitable for medical gas systems. The tube shall be installed in conformance
with the requirements of the National Fire Protection Association (NFPA) Standard 99, Gas and Vacuum Systems (NFPA) Standard
99C, Standard for Hypobaric Facilities (NFPA) Standard 99B, and Canadian Standards Association (CSA) Standard
Z 305.1 ⁄Z 7396.1, Nonflammable Medical Gas Piping Systems.
NOTE 1—Types K and L tube are defined in Specification B88.
NOTE 2—Drawn temper tube is suitable for use with capillary (solder joint) fittings for brazing.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazard caveat pertains only to the test method portion of Section 12 of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory
2
limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
B88 Specification for Seamless Copper Water Tube
B280 Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
B601 Classification for Temper Designations for Copper and Copper Alloys—Wrought and Cast
B846 Terminology for Copper and Copper Alloys
E8/E8M Test Methods for Tension Testing of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
4
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)
E243 Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
E255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
1
This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.04 on Pipe and
Tube.
Current edition approved March 1, 2018Oct. 1, 2019. Published March 2018October 2019. Originally approved in 1992. Last previous edition approved in 20112018 as
B819 – 00 (2011).B819–18. DOI: 10.1520/B0819-18.10.1520/B0819–19.
2
The UNS system for copper and copper alloys (see Practice E527) is a simple expansion of the former standard system accomplished by the addition of a prefix “C”
and a suffix “00.” The suffix can be used to accommodate composition variation of the base alloy.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B819 − 19
2.2 Other Standards:
National Fire Protection Association (NFPA) 99, Gas and Vacuum Systems (NFPA) 99C and Standard for Hypobaric Facilities
5
(NFPA) 99B
6
Compress
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.