ASTM A623-02

Standard Specification for Tin Mill Products, General Requirements

SCOPE
1.1 This specification covers a group of common requirements which, unless otherwise specified in the purchase order or in an individual specification, shall apply to tin mill products.
1.2 In case of any conflict in requirements, the requirements of the purchase order, the individual material specification, and this general specification shall prevail in the sequence named.
Note 1—A complete metric companion to Specification A 623 has been developed-Specification A 623M; therefore no metric equivalents are presented in this specification.
1.3 The following safety caveat pertains to through of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-May-2002
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.20 - Tin Mill Products

Relations

• Replaces: ASTM A623-00 - Standard Specification for Tin Mill Products, General Requirements
• Effective Date: 10-May-2002
• Replaced By: ASTM A623-02a - Standard Specification for Tin Mill Products, General Requirements
• Effective Date: 10-Nov-2002
• Referred By: ASTM A623M-22 - Standard Specification for Tin Mill Products, General Requirements [Metric]
• Effective Date: 10-May-2002
• Referred By: ASTM A657/A657M-18 - Standard Specification for Tin Mill Products, Black Plate Electrolytic Chromium-Coated, Single and Double Reduced
• Effective Date: 10-May-2002
• Referred By: ASTM A624/A624M-22 - Standard Specification for Tin Mill Products, Electrolytic Tin Plate, Single Reduced
• Effective Date: 10-May-2002
• Referred By: ASTM A625/A625M-13(2018) - Standard Specification for Tin Mill Products, Black Plate, Single-Reduced
• Effective Date: 10-May-2002
• Referred By: ASTM D5833-12(2020) - Standard Guide for Source Reduction Reuse, Recycling, or Disposal of Steel Cans
• Effective Date: 10-May-2002
• Referred By: ASTM A599/A599M-07(2017) - Standard Specification for Tin Mill Products, Electrolytic Tin-Coated, Cold-Rolled Sheet
• Effective Date: 10-May-2002
• Referred By: ASTM A987/A987M-19 - Standard Practice for Measuring Shape Characteristics of Tin Mill Products
• Effective Date: 10-May-2002
• Referred By: ASTM A650/A650M-18 - Standard Specification for Tin Mill Products, Black Plate, Double Reduced
• Effective Date: 10-May-2002
• Referred By: ASTM A370-23 - Standard Test Methods and Definitions for Mechanical Testing of Steel Products
• Effective Date: 10-May-2002
• Referred By: ASTM A626/A626M-22 - Standard Specification for Tin Mill Products, Electrolytic Tin Plate, Double Reduced
• Effective Date: 10-May-2002
• Referred By: ASTM E18-22 - Standard Test Methods for Rockwell Hardness of Metallic Materials
• Effective Date: 10-May-2002
• Referred By: ASTM B545-22 - Standard Specification for Electrodeposited Coatings of Tin
• Effective Date: 10-May-2002

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: A 623 – 02
Standard Specification for
1
Tin Mill Products, General Requirements
This standard is issued under the fixed designation A 623; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 2.2 U.S. Military Standards:
7
MIL-STD-129 Marking for Shipment and Storage
1.1 This specification covers a group of common require-
MIL-STD-163 Steel Mill Products, Preparation for Marking
ments which, unless otherwise specified in the purchase order
7
and Storage
or in an individual specification, shall apply to tin mill
2.3 U.S. Federal Standard:
products.
7
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
1.2 In case of any conflict in requirements, the requirements
of the purchase order, the individual material specification, and
3. Terminology
this general specification shall prevail in the sequence named.
3.1 Definitions:
NOTE 1—A complete metric companion to Specification A 623 has
3.1.1 base box, n—a unit of area equivalent to 112 sheets 14
been developed—Specification A 623M; therefore no metric equivalents
2 2
by 20 in. or 31 360 in. (217.78 ft ) (see Annex A1).
are presented in this specification.
3.1.2 base weight, n—a term used to describe the thickness
1.3 The following safety caveat pertains to Annex A3
of tin mill products. The designated base weight multiplied by
through Annex A10 of this specification: This standard does
a factor of 0.00011 is the nominal decimal thickness, in inches
not purport to address all of the safety concerns, if any,
of the material. Although it is customary industry-wide to use
associated with its use. It is the responsibility of the user of this
the term “pound” (for example, 75 lb), following the base
standard to establish appropriate safety and health practices
weight designation, base weight is correctly used only to define
and determine the applicability of regulatory limitations prior
material thickness, and is not a measure of the weight of a base
to use.
box.
3.1.3 black plate, n—light-gage, low-carbon, cold-reduced
2. Referenced Documents
steel intended for use in the untinned state or for the production
2.1 ASTM Standards:
of other tin mill products. It is supplied only in a dry or oiled
A 370 Test Methods and Definitions for Mechanical Testing
condition.
2
of Steel Products
3.1.4 box annealing, n—a process involving slow heating of
A 700 Practices for Packaging, Marking, and Loading
coils to a subcritical temperature, holding, and cooling there-
3
Methods for Steel Products for Domestic Shipment
from, to soften the strip and relieve stresses produced during
A 987 Test Method for Measuring Shape Characteristics of
cold reduction. It is accomplished in a sealed container. By
4
Tin Mill Products
introducing and maintaining an inert or slightly reducing
D 1125 Test Methods for Electrical Conductivity and Re-
atmosphere during the cycle, a relatively bright surface is
5
sistivity of Water
obtained.
E 18 Test Methods for Rockwell Hardness and Rockwell
3.1.5 bright finish, n—a surface that has a melted tin
6
Superficial Hardness of Metallic Materials
coating.
E 112 Test Methods for Determining the Average Grain
3.1.6 bundle, n—a unit containing two or more packages of
6
Size
a cut size, supported by a platform, generally consisting of ten
or more packages. (Also commonly referred to as a multiple-
package lift containing two or more packages.)
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
3.1.7 burr, n—metal displaced beyond the plane of the
Stainless Steel, and Related Alloys and is the direct responsibility of Subcommittee
surface by slitting or shearing (see 9.1.7 and 9.2.6).
A01.20 on Tin Mill Products.
Current edition approved May 10, 2002. Published July 2002. Originally 3.1.8 camber, n—the greatest deviation of a coil edge from
published as A 623 – 68. Last previous edition A 623 – 00.
a straight line. The measurement is taken on the concave side
2
Annual Book of ASTM Standards, Vol 01.03.
3
Annual Book of ASTM Standards, Vol 01.05.
4
Annual Book of ASTM Standards, Vol 01.06.
5 7
Annual Book of ASTM Standards, Vol 11.01. Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700
6
Annual Book of ASTM Standards, Vol 03.01. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by
...