EN ISO 8510-2:2010
(Main)Adhesives - Peel test for a flexible-bonded-to-rigid test specimen assembly - Part 2: 180 degree peel (ISO 8510-2:2006)
Adhesives - Peel test for a flexible-bonded-to-rigid test specimen assembly - Part 2: 180 degree peel (ISO 8510-2:2006)
ISO 8510-2:2006 specifies a 180° peel test for the determination, under specified conditions, of the peel resistance of a bonded assembly of two adherends where one adherend is flexible and the other is rigid.
Klebstoffe - Schälprüfung für flexibel/starr geklebte Proben - Teil 2: 180 Grad-Schälversuch (ISO 8510-2:2006)
Der vorliegende Teil von ISO 8510 legt einen 180°-Schälversuch unter festgelegten Bedingungen zur Bestimmung des Schälwiderstands von Klebungen aus zwei Fügeteilen, von denen einer flexibel und der andere starr ist, fest. Ein 90°-Schälversuch, der für weniger flexible Fügeteile geeignet ist, die beim 180°-Schälversuch reißen, brechen oder delaminieren, ist in ISO 8510-1 beschrieben.
Adhésifs - Essai de pelage pour un assemblage collé flexible-sur-rigide - Partie 2: Pelage à 180 degrés (ISO 8510-2:2006)
L'ISO 8510-2:2006 spécifie un essai de pelage à 180° pour la détermination, dans des conditions spécifiées, de la résistance au pelage d'un assemblage collé constitué de deux supports dont l'un est flexible et l'autre rigide.
Lepila - Lupilni preskus spoja gibkega in togega lepljenca - 2. del: Luščenje pod kotom 180° (ISO 8510-2:2006)
Ta del ISO 8510 določa lupilni preskus pod kotom 180° za določevanje odpornosti proti luščenju spoja dveh lepljencev pod določenimi pogoji, pri čemer je eden gibek in drugi tog. Lupilni preskus pod kotom 90°, primernejši za uporabo pri manj gibkih lepljencih, ki pri lupilnem preskusu pod kotom 180° pokajo, se lomijo ali razcepijo, je opisan v ISO 8510-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2011
1DGRPHãþD
SIST EN 28510-2:1998
/HSLOD/XSLOQLSUHVNXVVSRMDJLENHJDLQWRJHJDOHSOMHQFDGHO /XãþHQMHSRG
NRWRPƒ ,62
Adhesives - Peel test for a flexible-bonded-to-rigid test specimen assembly - Part 2: 180
degree peel (ISO 8510-2:2006)
Klebstoffe - Schälprüfung für flexibel/starr geklebte Proben - Teil 2: 180 Grad-
Schälversuch (ISO 8510-2:2006)
Adhésifs - Essai de pelage pour un assemblage collé flexible-sur-rigide - Partie 2: Pelage
à 180 degrés (ISO 8510-2:2006)
Ta slovenski standard je istoveten z: EN ISO 8510-2:2010
ICS:
83.180 Lepila Adhesives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 8510-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2010
ICS 83.180 Supersedes EN 28510-2:1993
English Version
Adhesives - Peel test for a flexible-bonded-to-rigid test specimen
assembly - Part 2: 180 degree peel (ISO 8510-2:2006)
Adhésifs - Essai de pelage pour un assemblage collé Klebstoffe - Schälprüfung für flexibel/starr geklebte Proben
flexible-sur-rigide - Partie 2: Pelage à 180 degrés (ISO - Teil 2: 180 Grad-Schälversuch (ISO 8510-2:2006)
8510-2:2006)
This European Standard was approved by CEN on 12 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8510-2:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 8510-2:2006 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 8510-2:2010 by
Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by AENOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at
the latest by March 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 28510-2:1993.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 8510-2:2006 has been approved by CEN as a EN ISO 8510-2:2010 without any modification.
INTERNATIONAL ISO
STANDARD 8510-2
Second edition
2006-12-01
Adhesives — Peel test for a
flexible-bonded-to-rigid test specimen
assembly —
Part 2:
180° peel
Adhésifs — Essai de pelage pour un assemblage collé
flexible-sur-rigide —
Partie 2: Pelage à 180°
Reference number
ISO 8510-2:2006(E)
©
ISO 2006
ISO 8510-2:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO 8510-2:2006(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Principle. 1
4 Apparatus . 1
5 Test specimens . 2
6 Conditioning and testing atmosphere. 3
7 Procedure . 3
8 Expression of results . 3
9 Precision. 4
10 Test report . 4
Bibliography . 6
ISO 8510-2:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 8510-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This second edition cancels and replaces the first edition (ISO 8510-2:1990), Clause 2 and Figure 1 of which
have been revised. In addition, minor editorial changes have been made in the text.
ISO 8510 consists of the following parts, under the general title Adhesives — Peel test for a flexible-bonded-
to-rigid test specimen assembly:
⎯ Part 1: 90° peel
⎯ Part 2: 180° peel
iv © ISO 2006 – All rights reserved
INTERNATIONAL STANDARD ISO 8510-2:2006(E)
Adhesives — Peel test for a flexible-bonded-to-rigid test
specimen assembly —
Part 2:
180° peel
SAFETY PRECAUTIONS — Persons using this document s
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.